3M G5, XT-1 operating instructions Fitting the Headset

Page 37

 

 

 

 

Operation

 

 

 

 

 

Flashing in this sequence

The Base Station you are trying to register your headset to, has more than 20

 

 

Red

4sec blank

headsets registered already

 

 

Red

4sec blank……..

Follow the steps below to remove any registered headsets that are not in use any

 

 

 

 

 

 

 

 

more.

 

 

 

 

1.

Log into the Base Station

 

 

 

 

2.

Press the Mode key till you see the System Menu

 

 

 

 

3.

Select 04 Registration

 

 

 

 

4.

Select 02 Remove Headsets.

 

 

 

 

5.

Scroll to the number of the headset you want to un-register.

 

 

 

 

6.

Press Enter.

 

 

 

 

 

 

Blue (at Mic Boom tip)

Solid blue, when holding the Volume touch zone, indicates that the headset is

 

 

 

 

listening for a special key sequence (e.g. for headset deregistration)

 

 

 

 

Blue flash when vehicle arrives in a lane (in addition to the vehicle present beep

 

 

 

 

(single beep on Lane1 or double beep on Lane 2).

 

 

 

 

 

 

 

Fitting the Headset

Make the following adjustments to the headset to make it comfortable, less likely to fall off and easy for you to hear and speak clearly:

1.Adjust the size of the headband until the ear pad rests against one ear and the comfort pad cushion rests just above the other ear.

2.To create a tighter fit, hold the headset with one hand on the Pod area and the other hand on the Comfort Pad area. Gently bring the two hands close to one another, then past one another. Slowly move one end back and forth.

This ensures pressure is applied equally along the length of the headband. Applying excessive force in one area alone will create a crease on the headband.

3.Rotate the microphone boom up or down so its tip is in line with the corner of your mouth. Do not bend the boom.

Adjustment

Slide

3M™ Drive-Thru Systems Model G5 and Model XT-1

November 6 2014 – Revision 2.1

Operating Instructions

Page 37 of 77

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Operating Instructions 3M Commercial Solutions Division Table of Contents Assembling a 3M Drive Thru Headset G5 Maintenance Index Alert Message External Trigger InputsOverview Safety InformationImportant Notes and Notes Other ConventionsImportant Note FCC and Industry Canada InformationFCC and IC Identifiers FCC NoteRecycling / Disposal Notice to European Union customers Enter Configuration Mode ConfigurationNavigating the Base Station Display Buttons Interpreting Display InformationConfiguring with a Computer Logging into the Base Station with a PC ∙ Cycle the power to the base stationInbound Microphone Volume Change Basic Volume SettingsOutbound Talk Volume Vehicle Alert VolumeInbound Listen Change the Monitor VolumeOutbound Talk Vehicle PresentVehicle Approach Change the Night VolumeMessages Greeter MessagesAdd Headsets Registering HeadsetsRemove Headsets Resetting Inactive Days List All HeadsetsChange Noise Reduction Level Checking Headset Software RevisionAcoustic Echo Canceller Change Global SettingsDrive Thru Audio Duplex Mode Set System Date and TimeNumber of Base Stations at this Site Channel Heard by Order TakerStore is Now Closed Prompt Customer Order Point Prompt Language Pull Ahead PromptOrder Point Talk with No Vehicle Order Takers and Page Messages in Cross Lane ModeDetector Type Important Notes Kitchen Noise ReductionXT-1 Basestation Software Update Kit XT-1 Order Taking Modes SetupHaptics Vibration Alerts on Headsets Blue LED Alerts on HeadsetsRegular Site Schedule Change Site SchedulingHoliday/Exception Schedule Change Self Monitoring Change Site InformationChange Passcodes User PasscodesInstaller Setup Two Base Station SetupLoad Installation Settings Save Installation SettingsReboot System Factory Setup Restore Factory DefaultsActivate the Backup Intercom Create and Load TemplatesPage 3M Drive Thru Headset G5 OperationNovember 6 2014 Revision Operation 3M Drive-Thru Systems Model G5 and Model XT-1 ∙ T1 and T2 Talkbuttons Connect you to the order point Component Identification and DescriptionG5 Battery Indicator Light Modes Indicator Light ModesG5 Headset Indicator Light Modes Fitting the Headset Replace the Battery Cleaning XT-1 HeadsetsOut of Range Component Identification and Description Headset Replace the Battery Out of Range Navigating in the Base Station in Run Mode Base Station SetupChange Order Taking Mode Listen Auto, Manual, and Always On Explanation of Order Taking ModesTalk Manual Latching, Push to Talk, Automatic Change Lane Mode Which Order Taking Mode to SelectSplit Lane Cross Lane Change Volume ModeG5 Headset MaintenanceReplacing the Carrier Disassembling the Carrier from the PodRefitting the headset with the new Carrier G5 Headset ChargerReplacing the Ear and Headband Pads LocationLow Battery Message Cleaning the Contacts in the Headset Charger wellsG5 Batteries Care, Handling and StorageMaking Sure Batteries are Ready for Use Disposing of BatteriesImportant Information about Rechargeable Batteries Cleaning the Contacts XT-1 Battery ChargerXT-1 Headset XT-1 BatteriesCharging Status Indicator Important Information about Rechargeable Batteries Headset Indicator Lights TroubleshootingG5 Headset Indicator Light Modes Problem Possible Cause Solution General TroubleshootingPress the other button into the correct XT-1 Battery and Battery Charger Battery and Battery Charger TroubleshootingAppendix Declaration of Conformity Physical Appendix Base Station SpecificationsElectrical FunctionalAppendix G5 Charger Specifications Enter the Greeter Configuration Menu Greeter SetupAppendix Greeter Module Record Message Message ActivationChoose Headsets Messages Playback To NameBreakfast Service=StartMessage Daypart Definitions Change Playback Delay TimeGreeter Message Properties Set Greeter Playback through Headsets Change Playback ModeTurn on Tone to Headsets During Greeter Playback Set Playback through MonitorTurn on External Detector Playback Message Turn on Restaurant Closed Playback MessageGreeter Revision Alert & Reminder Message Properties Alert & Reminder Message PropertiesDual Lane Systems Lane Message NamesTandem Pull Ahead Playback Message Delay Count Greeter Setup System DefaultsStart Time Alert & Reminder Properties Greeter Setup Customer SettingsGreeter Setup Example Settings 66, 67, 68, 69 IndexTalk 3M, Thinsulate, Tufcote and ScotchBrite are trademarks of 3M
Related manuals
Manual 8 pages 46.54 Kb

G5, XT-1 specifications

The 3M G5 XT-1 is a cutting-edge respirator designed for professionals who require advanced protection in various hazardous environments. With its innovative features, this respirator stands out in the market, providing users with an optimal balance of safety, comfort, and performance.

One of the main features of the 3M G5 XT-1 is its advanced filtration technology. Equipped with highly efficient particulate filters, these respirators are designed to capture airborne particles, including dust, smoke, and other harmful contaminants. This effectiveness is further enhanced by the use of activated carbon in certain filter models, which provides an additional layer of protection against gases and odors. The filters are easy to replace, ensuring that users can maintain their equipment without hassle.

Another key characteristic of the G5 XT-1 is its ergonomic design. The respirator is engineered to provide an excellent fit, reducing the likelihood of leakage and ensuring that users receive optimal protection. The adjustable straps and customizable nose bridge allow for a snug fit on various face shapes and sizes, enhancing comfort during prolonged use. This is particularly important for professionals in fields such as construction, healthcare, and manufacturing, who may wear respirators for extended periods.

The G5 XT-1 also features a lightweight construction, which contributes to user comfort. This lightweight design, combined with features such as breathing valves, enhances airflow, reducing breathing resistance. This means that users can perform their tasks more efficiently while experiencing less fatigue.

Another notable technology integrated into the G5 XT-1 is its dual mode of operation. Users can switch between disposable and reusable options, which is particularly advantageous for those who want to balance cost and sustainability. The reusable aspect of the respirator also encourages environmental friendliness by reducing waste.

In conclusion, the 3M G5 XT-1 respirator is a comprehensive solution for those seeking high-performance respiratory protection. With its advanced filtration technologies, user-centric design, and flexible operation modes, the G5 XT-1 meets the diverse needs of professionals working in challenging environments. Its focus on safety, comfort, and adaptability secures its place as a top choice for respiratory protection in various industries.
Top Page Image Contents