Zebra Technologies 110PAX4 manuals
Computer Equipment > Printer Accessories
When we buy new device such as Zebra Technologies 110PAX4 we often through away most of the documentation but the warranty.
Very often issues with Zebra Technologies 110PAX4 begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Printer Accessories Zebra Technologies 110PAX4 is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Printer Accessories on our side using links below.
Zebra Technologies 110PAX4 Manual
164 pages 6.25 Mb
2 © 2011 ZIH Corp(17 U.S.C.506). Copyright violators may be subject to civil liability Proprietary Statement Product Improvements Liability Disclaimer Limitation of Liability FCC Radiation Exposure Statement (for printers with radios or RFID encoders) Part Number: 57512L-004 3 Zebra PAX4 SeriesPAX Applicable Directives and Supporting Standards: 89/336/EEC EMC Directive, EN55022:1998 Class A, EN61000-6-2 EN61000-3-2, EN61000-3-3W/Amendment 73/23/EEC LVD Directive, EN60950-1:03,CB Scheme FCC Part 15, Subpart B, Class A, ICES-003 NOM 019-SCFI-1998 C-TICK,VCCI Manufactured By: Zebra Technologies Corporation Manufactured By: Effective Date: 1 Jan 4 Compliance InformationFCC Compliance Statement Canadian DOC Compliance Statement 5 Contents9 About This Document15 Introduction21 Print Engine Setup39 Operations57 Configuration58 Setup Mode60 Change Password-ProtectedParametersDefault Password Value Disable the Password Protection Feature 61 Print a Configuration Label62 Print a Network Configuration Label63 Control Panel ParametersHow to View or Modify Parameters Additional Parameters 64 Standard Print Engine Parameters65 Table 7 • Print Engine Parameters (Page 2 of 25)Adjust Backfeed Speed BACKFEED SPEED Default: 2 IPS Adjust the Tear-OffPosition TEAR OFF +000 Figure 21 • Tear-OffPosition Adjustment Default: +0 66 ^LLxxxx67 Set Print WidthPRINT WIDTH - 168 0/8 MM 68 Table 7 • Print Engine Parameters (Page 5 of 25)Set Maximum Label Length MAXIMUM LENGTH 39.0IN Figure 22 • Label Length 69 Table 7 • Print Engine Parameters (Page 6 of 25)Set Early Warning for Media EARLY WARNING When this parameter is enabled, the print engine provides warnings when MEDIA DISABLED labels are running low Note • Update the number of labels per roll when beginning use of the Early Warning System. The print engine does not make any adjustments when power is turned off and on Default: MEDIA DISABLED Selections: MEDIA DISABLED, MEDIA ENABLED To change the Early Warning settings: 1. When the LCD displays EARLY WARNING MEDIA, press the left or right oval to toggle between ENABLED and DISABLED. (If you are Change Password-ProtectedParameters on page 60.) 2. If you enable the Early Warning System, do the following: a. Exit Setup mode and save changes to enable additional parameters b. Enter Setup mode again. The media and ribbon parameters (LABELS PER ROLL, MEDIA REPLACED, RIBBON LENGTH, and RIBBON REPLACED) appear , and ) appear c. Adjust the settings as necessary (descriptions of each of these parameters follows) Set Number of Labels Per Roll for Early Warning LABELS PER ROLL This parameter appears only when Early Warning for Media is enabled This value should correspond to the number of labels per roll of the media that you are using Range: 100 to WARNING MEDIA LOW MEDIA REPLACED 3.If you replaced the media, press the right oval to select YES to clear 70 Table 7 • Print Engine Parameters (Page 7 of 25)Reset Media Counter for Early Warning MEDIA REPLACED Set Ribbon Length for Early Warning RIBBON LENGTH - 450M 1476 FT WARNING RIBBON LOW RIBBON REPLACED Reset Ribbon Counter for Early Warning RIBBON REPLACED 71 Set Early Warning for MaintenanceMAINT. OFF EARLY WARNING MAINTENANCE OFF Set Printhead Cleaning Interval for Early Warning HEAD CLEANING WARNING CLEAN PRINTHEAD with HEAD CLEANED Reset Printhead Cleaning Counter for Early Warning HEAD CLEANED 72 Table 7 • Print Engine Parameters (Page 9 of 25)Set Printhead Life for Early Warning HEAD LIFE 1000000 IN WARNING REPLACE HEAD NEW PRINTHEAD YES Reset Printhead Life Counter for Early Warning NEW PRINTHEAD NO List Fonts LIST FONTS PRINT List Bar Codes LIST BAR CODES 73 Table 7 • Print Engine Parameters (Page 10 of 25)List Images LIST IMAGES List Formats LIST FORMATS List Setup LIST SETUP List Network Settings LIST NETWORK List All LIST ALL 74 Table 7 • Print Engine Parameters (Page 11 of 25)Format Memory Card FORMAT CARD: This option erases all previously stored information from the optional PCMCIA card or Compact Flash card To format a memory card: 1.Press the left oval to select A: or the right oval to select B: Enter the password. For instructions, see Change Password-Protected Parameters ARE YOU SURE 4.Do you wish to continue •Press the left oval to select NO to cancel the request and return to FORMAT CARD prompt prompt •Press the right oval to select YES and begin initialization CHECKING B: MEMORY PRINTER IDLE 75 Table 7 • Print Engine Parameters (Page 12 of 25)Initialize Flash Memory INIT FLASH MEM This option erases all previously stored information from Flash memory To initialize Flash memory: 1.Press the right oval to select YES The display shows INITIALIZE FLASH 3.Press the right oval to select YES The display shows ARE YOU SURE •Press the left oval to select NO to cancel the request and return to the INITIALIZE FLASH prompt CHECKING E: MEMORY 76 Table 7 • Print Engine Parameters (Page 13 of 25)Print Sensor Profile SENSOR PROFILE Figure 23 • Sensor Profile 77 Table 7 • Print Engine Parameters (Page 14 of 25)Calibrate Media and Ribbon Sensor Sensitivity MEDIA AND RIBBON CALIBRATE LOAD BACKING REMOVE RIBBON The message CALIBRATING PLEASE WAIT displays RELOAD ALL 78 Table 7 • Print Engine Parameters (Page 15 of 25)Set Parallel Communications PARALLEL COMM -BIDIRECTIONAL Set Serial Communications SERIAL COMM -RS232 Default: RS232 Set Baud BAUD Set Data Bits DATA BITS - 8 BITS Default: 8 BITS 79 Table 7 • Print Engine Parameters (Page 16 of 25)Set Parity PARITY Default: NONE Set Host Handshake HOST Default: XON/XOFF Set Protocol PROTOCOL ZEBRA ACK_NAK DTR/DSR Set Network ID NETWORK ID 80 Table 7 • Print Engine Parameters (Page 17 of 25)Set Communications Mode COMMUNICATIONS - NORMAL MODE Set Control Prefix Character CONTROL PREFIX >7EH Set Format Prefix Character FORMAT PREFIX <^>5EH 81 Table 7 • Print Engine Parameters (Page 18 of 25)Set Delimiter Character DELIMITER CHAR <,>2CH Select ZPL Mode ZPL MODE ZPL Default: ZPL Selections: ZPL II, ZPL Select Media Power-UpOption MEDIA POWER UP - CALIBRATION+ Feed Calibration Length Short Cal Motion 82 Table 7 • Print Engine Parameters (Page 19 of 25)Select Head Close Option HEAD CLOSE Select Backfeed Sequence BACKFEED Adjust Label Top Position LABEL TOP +000 Default: +000 83 Table 7 • Print Engine Parameters (Page 20 of 25)Adjust Left Position LEFT POSITION ±0000 Set the Printhead Resistor Value HEAD RESISTOR 0500 OHMS Initial Value: Default Value: 84 Table 7 • Print Engine Parameters (Page 21 of 25)Set Applicator Port Mode APPLICATOR PORT Default: OFF OFF: MODE 1: MODE 2: MODE 3: MODE 4: Set Applicator Error Signal When Print Engine Pauses ERROR ON PAUSE - ENABLED Default: ENABLED 85 Table 7 • Print Engine Parameters (Page 22 of 25)Select Start Print Signal START PRINT SIG - PULSE MODE PULSE MODE LEVEL Select Resynch Mode RESYNCH MODE FEED MODE Default: FEED MODE Error Condition Feed Label Head Close 86 Table 7 • Print Engine Parameters (Page 23 of 25)Set Ribbon Low Mode RIBBON LOW MODE 25M LOW RIBBON RIBBON LOW RIBBON LOW OUTPUT Default: 25M Set Ribbon Low Output RIB LOW OUTPUT ACTIVE HIGH Set Reprint Mode REPRINT MODE DISABLED Default: DISABLED 87 Table 7 • Print Engine Parameters (Page 24 of 25)WEB S MEDIA S RIBBON S MARK S MARK MED S MEDIA LED RIBBON LED MARK LED Adjust LCD Display LCD ADJUST +10 Select Format Convert FORMAT CONVERT - NONE Set RTS Take-UpDancer Arm Calibration Value RTS TAKEUP ARM 88 Table 7 • Print Engine Parameters (Page 25 of 25)Set RTS Supply Dancer Arm Calibration Value RTS SUPPLY ARM Select Idle Display IDLE DISPLAY - FW VERSION Set Real-TimeClock (RTC) Date RTC DATE - 01/31/01 in IDLE DISPLAY Set RTC Time RTC TIME 14:55 Select the Display Language LANGUAGE ENGLISH Default: ENGLISH 89 Routine Maintenance101 Troubleshooting131 Data Ports147 Specifications157 Index
Also you can find more Zebra Technologies manuals or manuals for other Computer Equipment.