82Configuration

Control Panel Parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table 7 • Print Engine Parameters (Page 19 of 25)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parameter

 

Action/Explanation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select Head Close Option

 

HEAD CLOSE

 

 

 

This parameter sets the action of the media when you close the printhead.

 

- CALIBRATION+

 

Default: CALIBRATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Selections: FEED, CALIBRATION, LENGTH, SHORT CAL, and NO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MOTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Feed—feeds the labels to the first registration point.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Calibration—determines the length of the label and adjusts the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

sensor settings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Length—In continuous mode, feeds the last stored label length. In

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

noncontinuous mode, calibrates based on the maximum label length

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

setting (see Set Maximum Label Length on page 68).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Short Cal—calibrates label length using the current sensor settings.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• No Motion—the media does not move. You must press FEED to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cause the print engine to resynch to the start of the next label.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To change the value shown:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Press the left or right oval to scroll through the options.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Select Backfeed Sequence

 

BACKFEED

 

 

 

This parameter establishes when label backfeed occurs after a label is

 

-

 

 

 

 

 

 

 

 

BEFORE

+

removed in applicator mode. It has no effect in Rewind mode. This setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

is superseded by ~JS when received as part of a label format. See the ZPL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

II Programming Guide for more information.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Default: BEFORE for non-RFID print engine, AFTER for print engine

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

with RFID reader installed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Selections: DEFAULT, AFTER, BEFORE, OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To change the value shown:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Press the left or right oval to scroll through the options.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Adjust Label Top Position

 

LABEL TOP +000

 

 

 

This parameter adjusts the print position vertically on the label. Positive

 

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

+

numbers adjust the label top position farther down the label (away from the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

printhead); negative numbers adjust the position up the label (toward the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

printhead). The displayed value represents dots.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Default: +000

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Range: –120 to +120 dots

To change the value shown:

1.Press the right oval to increase the value.

2.Press the left oval to decrease the value.

57512L-004 Rev. A

110PAX4/R110PAX4 User Guide

6/29/11