Response Adjustment | A&D GH-120/GH-200/GH-300/GH-202/GH-252

7.Response Adjustment

This function stabilizes the weight value, reducing the influence on weighing that is caused by drafts and/or vibration at the place where the balance is installed. This function adjusts by automatically analyzing the environment or by hand-operation. The function has three stages as follows :

Indicator	Parameter		Response	Stability
FAST	Cond 0		Fast response,	Sensitive value
MID.	Cond	1	Slow response, Stable value
SLOW	Cond	2	Slow response, Stable value

Response indicator

7.1.Automatic Response Adjustment

This function automatically updates the response adjustment by analyzing the influence of the environment using the internal mass.

1 Press and hold the MODE key until RESPONSE is displayed, then release the key.

2The balance automatically sets the response characteristic.

Caution Do not allow vibration or drafts to affect the balance during adjustment.

3After automatic adjustment, the balance displays end , returns to the weighing mode and displays the updated response indicator for about thirty seconds.

Press and hold

Release

Result

Note

If the automatic response adjustment fails, the balance displays CH ng . Check the ambient

conditions such as breeze and vibration, also check the weighing pan. Then, perform the


adjustment again. To return to the weighing mode, press the						key.
adjustment again. To return to the weighing mode, press the				CAL		key.
If there is matter on the weighing pan, the balance displays						. Remove them from the
				CH 0		. Remove them from the
pan. To return to the weighing mode, press the		key.
pan. To return to the weighing mode, press the	CAL	key.

Advise

If the automatic response adjustment is not helpful, try "7.2. Manual Response Adjustment".

21

Image 23

A&D GH-120/GH-200/GH-300/GH-202/GH-252 manual Automatic Response Adjustment, Advise

Contents

1WMPD4000891C GH-120 GH-200 GH-300 GH-202 GH-252Page Contents Interface And Communication Underhook Density Measurement About This Manual Introduction Compliance With EMC Directives FeaturesCompliance Compliance With FCC RulesPage Unpacking the Balance Before Use PrecautionsInstalling the Balance Shock During Use After Use Power Supply Key operation Display Symbols and Key OperationKey When pressed and released When pressed and held Display Units Weighing Units 101 00001 Balance displays Counting mode Pcs Percent mode Densitymode Press the PrintChanging the Units Examples Unit Display Gram Unit setting example Weighing Precautions for the weighing operationBasic Operation Gram Mode Read . Display symbols and Key operation before operation 1mg Dual RangeWeighing range Available minimum display 01mg Counting operation Counting Mode PCSStoring a sample unit mass Weighing input mode Mark turns off after Unit mass is improved Repeat Counting mode using the Acai function Reading the percentage Percent Mode %Selecting the percent mode Storing the 100% reference mass Advise Response AdjustmentAutomatic Response Adjustment Press Key again quickly Manual Response AdjustmentKey until Displayed, then release the key Calibration Group Calibration Mark Automatic self calibration due to changes in temperatureAutomatic Self Calibration One-Touch Calibration Press and hold the CAL Key until is CC Calibration Test Using the Internal Mass Calibration Using an External Weight Even if the AC adapter is removed, Calibration Test Using an External WeightKey................. The key To cancel the operation Key ..............The key to store the new mass value Correcting the Internal Mass Value Permit or Inhibit Function Switch and Initialization Key to display Press the Print key To cancel this operation, pressInitializing the Balance Function Table Setting the Function Table Display symbol and keys Key to enter the class Key to select a item Press Setting procedureFunction table is displayed Press Key to select a class Press Setting example Details of the Function Table ID number output Factory settingsInt Data output Time/Date output Interface Ct5 5if TimeoutAK, Error code ErCd Description of the Class Environment, Display Auto print modes a and B Description of the Item Data Output ModeKey mode Stream mode DP Dump print format Interval memory modeDescription of the Item Data Format Standard format Data Unit Terminator Stable value Unstable value KF formatMT format NU numerical format Time CSV formatData number Date Stable Unstable Overload Positive errorNegative error Space Data Format Examples Units Confirming the time Setting the timeClock and Calendar Function Operation Set the date Store Setting the dateQuitting the operation ID Number and GLP Report Setting the ID Number Key operation Calibration report using the internal massGLP Report Commad Calibration test report using an internal massBalance returns to weighing mode after this test Calibration report using an external weight When using preset target value, proceed to step Calibration test report using an external weight Weighing data Title block and end blockTitle block Press and hold the Print key until the key Returns to the weighing modeData Memory Releasing Clr or err Interval memory Data Memory for Weighing DataStoring the weighing data Memory full Enabling the data memory function Setting the function tableParameter settings for each output mode are as follows Additional parameter settings, as follows Deleting all memory data at one time Recalling the memory dataTransmitting all memory data at one time Deleting data stored in memory Data Memory for Calibration and Calibration TestStoring the calibration and calibration test data Transmitting the memory data Underhook Density of a liquid Density MeasurementFormula to obtain the density Prior to measurement Changing the function table Entering the density of a liquid Relation between the water temperature and density Key to proceed to other Measuring the densityOutput or store Density display Turns off. lights Press the modes Sub 25 pin assignments Standard Input and Output InterfaceRS-232C Interface Connection to an AD-8121B printer Connection to Peripheral Equipment RsCom Using Windows Communication Tools Software WinCTUsing the WinCT software, the balance can do the following Connection to a computer and the use of WinCT Command List Commands Settings Related to RS-232C Acknowledge Code and Error CodesControl Using CTS and RTS Command Re-zeroing the display Command ExamplesOn command turning on the balance Error code CAL command Calibration with internal mass Weighing with a tare Command ?PT command Net value Tare value Zero Command ExecutionPT command to set a target weight of 10 g Zero display Treatment of the Balance MaintenanceError Codes Automatic response adjustment unstable error Sample mass errorUnit mass error Automatic response adjustment zero error Other Display Asking for Repair Checking the Balance Performance and EnvironmentChecking that the balance performs properly Specifications Unit mm External Dimensions AD-8121B Printer Options and Peripheral EquipmentGH-02 USB interface GH-08 Ethernet Interface 9970 g/cm3 AD-1653 Density Determination KitAD-1683 DC Static Eliminator AX-USB-9P-EX USB Converter AX-T-314A-S External key Plug AX-SW128 Foot switch Other options Terms Terms/Index Index Tare PU5e Options5pd Out 5tart Memo Memo