Permit or Inhibit | A&D GH-120/GH-200/GH-300/GH-202/GH-252 instruction

9.Function Switch and Initialization

9.1.Permit or Inhibit

The balance stores parameters that must not be changed unintentionally (Example: Calibration data for accurate weighing, Data for adapting to the operating environment, Control data for the RS-232C interface). There are five switches for the purpose of protecting parameters. Each switch can select either "permit" or "inhibit". "Inhibit" protects parameters against unintentional operations.

1 Press the

ON:OFF

key to turn off the display.

2 While pressing and holding the PRINT press the ON:OFF key to display p5

key and the

.

RANGE

key,

3 Press the

PRINT

key. Then the balance displays the function switches.

4Specify the switches using the following keys. RANGE key ...........The key to select blinking digit.

RE-ZEROkey.........The key to change the parameter for the selected switch. 0 To inhibit changes. (Can not be used.)

1 To permit changes. (Can be used.)

PRINT key .............The key to store the new parameter and return to the weighing mode.
.................	The key to cancel current operation and return to the weighing mode.
CAL key

Function table

0To inhibit changes to the function table.

1To permit changes to the function table.

Calibration using the internal mass (One-touch calibration)

0To inhibit calibration using the internal mass.

1To permit calibration using the internal mass.

Calibration using the external weight

0To inhibit calibration using the external weight.

1To permit calibration using the external weight.

Automatic self calibration (due to changes of ambient temperature)

0To inhibit automatic self calibration.

1To permit automatic self calibration.

Internal mass correction

0To inhibit correction.

1To permit correction.

29

Image 31

A&D GH-120/GH-200/GH-300/GH-202/GH-252 manual Function Switch and Initialization, Permit or Inhibit

Contents

1WMPD4000891C GH-120 GH-200 GH-300 GH-202 GH-252Page Contents Interface And Communication Underhook Density Measurement About This Manual Introduction Compliance With EMC Directives FeaturesCompliance Compliance With FCC RulesPage Unpacking the Balance Installing the Balance PrecautionsBefore Use Shock During Use After Use Power Supply Key operation Display Symbols and Key OperationKey When pressed and released When pressed and held Display Units Weighing Units 101 00001 Balance displays Counting mode Pcs Percent mode Densitymode Press the PrintChanging the Units Examples Unit Display Gram Unit setting example Weighing Precautions for the weighing operationBasic Operation Gram Mode Read . Display symbols and Key operation before operation 1mg Dual RangeWeighing range Available minimum display 01mg Storing a sample unit mass Weighing input mode Counting Mode PCSCounting operation Mark turns off after Unit mass is improved Repeat Counting mode using the Acai function Reading the percentage Percent Mode %Selecting the percent mode Storing the 100% reference mass Automatic Response Adjustment Response AdjustmentAdvise Press Key again quickly Manual Response AdjustmentKey until Displayed, then release the key Calibration Group Calibration Mark Automatic self calibration due to changes in temperatureAutomatic Self Calibration One-Touch Calibration Press and hold the CAL Key until is CC Calibration Test Using the Internal Mass Calibration Using an External Weight Even if the AC adapter is removed, Calibration Test Using an External WeightKey................. The key To cancel the operation Key ..............The key to store the new mass value Correcting the Internal Mass Value Permit or Inhibit Function Switch and Initialization Initializing the Balance Press the Print key To cancel this operation, pressKey to display Function Table Setting the Function Table Display symbol and keys Key to enter the class Key to select a item Press Setting procedureFunction table is displayed Press Key to select a class Press Setting example Details of the Function Table ID number output Factory settingsInt Data output Time/Date output Interface Ct5 5if TimeoutAK, Error code ErCd Description of the Class Environment, Display Auto print modes a and B Description of the Item Data Output ModeKey mode Stream mode DP Dump print format Interval memory modeDescription of the Item Data Format Standard format Data Unit Terminator Stable value Unstable value KF formatMT format NU numerical format Time CSV formatData number Date Stable Unstable Overload Positive errorNegative error Space Data Format Examples Units Confirming the time Setting the timeClock and Calendar Function Operation Quitting the operation Setting the dateSet the date Store ID Number and GLP Report Setting the ID Number GLP Report Calibration report using the internal massKey operation Balance returns to weighing mode after this test Calibration test report using an internal massCommad Calibration report using an external weight When using preset target value, proceed to step Calibration test report using an external weight Title block Title block and end blockWeighing data Press and hold the Print key until the key Returns to the weighing modeData Memory Releasing Clr or err Interval memory Data Memory for Weighing DataStoring the weighing data Memory full Enabling the data memory function Setting the function tableParameter settings for each output mode are as follows Additional parameter settings, as follows Transmitting all memory data at one time Recalling the memory dataDeleting all memory data at one time Deleting data stored in memory Data Memory for Calibration and Calibration TestStoring the calibration and calibration test data Transmitting the memory data Underhook Density of a liquid Density MeasurementFormula to obtain the density Prior to measurement Changing the function table Entering the density of a liquid Relation between the water temperature and density Key to proceed to other Measuring the densityOutput or store Density display Turns off. lights Press the modes RS-232C Interface Standard Input and Output InterfaceSub 25 pin assignments Connection to an AD-8121B printer Connection to Peripheral Equipment RsCom Using Windows Communication Tools Software WinCTUsing the WinCT software, the balance can do the following Connection to a computer and the use of WinCT Command List Commands Control Using CTS and RTS Acknowledge Code and Error CodesSettings Related to RS-232C On command turning on the balance Command ExamplesCommand Re-zeroing the display Error code CAL command Calibration with internal mass Weighing with a tare Command ?PT command Net value Tare value PT command to set a target weight of 10 g Zero display Command ExecutionZero Error Codes MaintenanceTreatment of the Balance Automatic response adjustment unstable error Sample mass errorUnit mass error Automatic response adjustment zero error Other Display Checking that the balance performs properly Checking the Balance Performance and EnvironmentAsking for Repair Specifications Unit mm External Dimensions AD-8121B Printer Options and Peripheral EquipmentGH-02 USB interface GH-08 Ethernet Interface 9970 g/cm3 AD-1653 Density Determination KitAD-1683 DC Static Eliminator AX-USB-9P-EX USB Converter AX-T-314A-S External key Plug AX-SW128 Foot switch Other options Terms Terms/Index Index Tare PU5e Options5pd Out 5tart Memo Memo