Setting the function table | A&D GH-120/GH-200/GH-300/GH-202/GH-252

Automatic self calibration can not be used while the interval memory mode is active. The following commands can not be used during data storage.

QQuery command for weighing data.

SQuery command for stable weighing data. SI Query command for weighing data.

SIR Query command for continuous weighing data.

Setting the function table

Parameter settings for each output mode are as follows:

	Item	Data output	Auto print polarity,	Data memory	Interval time
	Mode	mode	difference	function	Interval time
	Mode	mode	difference	function
	Key mode	prt 0	Not used	data 1	Not used
	Auto print mode A	prt 1	ap-a 0-2	data 1	Not used
	Auto print mode B	prt 2	ap-b 0-2	data 1
	Interval memory mode	prt 3	Not used	data 1	int 0-8

Additional parameter settings, as follows:

	Data number	No	d-no 0
		Yes	d-no 1

	ID number	No	5-id 0
		Yes	5-id 1

		No	5-td 0
	Time and date	Time only	5-td 1
		Date only	5-td	2

		Both	5-td	3

Enabling the data memory function

1

Press and hold the

key until

ba5fnc

is displayed, then release the key.

RANGE

2

Press the

key several times to display

.

dout

RANGE

3

Press the

key.

PRINT

4

Press the

key three times to display

.

data 0

RANGE

5

Press the

key to display

.

data 1

RE-ZERO

6

Press the

key to store the setting.

PRINT

7

Press the

key to return to the weighing mode.

CAL

54

Image 56

A&D GH-120/GH-200/GH-300/GH-202/GH-252 manual Setting the function table, Enabling the data memory function

Contents

GH-120 GH-200 GH-300 GH-202 GH-252 1WMPD4000891CPage Contents Underhook Density Measurement Interface And Communication Introduction About This Manual Features ComplianceCompliance With FCC Rules Compliance With EMC DirectivesPage Unpacking the Balance Before Use PrecautionsInstalling the Balance During Use Shock Power Supply After Use Display Symbols and Key Operation Key When pressed and released When pressed and heldDisplay Key operation Weighing Units Units 101 00001 Counting mode Pcs Percent mode Densitymode Press the Print Changing the UnitsExamples Unit Display Gram Balance displays Unit setting example Precautions for the weighing operation Basic Operation Gram ModeRead . Display symbols and Key operation before operation Weighing Dual Range Weighing range Available minimum display01mg 1mg Counting operation Counting Mode PCSStoring a sample unit mass Weighing input mode Counting mode using the Acai function Mark turns off after Unit mass is improved Repeat Percent Mode % Selecting the percent modeStoring the 100% reference mass Reading the percentage Advise Response AdjustmentAutomatic Response Adjustment Manual Response Adjustment Key untilDisplayed, then release the key Press Key again quickly Calibration Calibration Group Automatic self calibration due to changes in temperature Automatic Self CalibrationOne-Touch Calibration Mark Calibration Test Using the Internal Mass Press and hold the CAL Key until is CC Calibration Using an External Weight Calibration Test Using an External Weight Key................. The key To cancel the operationKey ..............The key to store the new mass value Even if the AC adapter is removed, Correcting the Internal Mass Value Function Switch and Initialization Permit or Inhibit Key to display Press the Print key To cancel this operation, pressInitializing the Balance Setting the Function Table Display symbol and keys Function Table Setting procedure Function table is displayed PressKey to select a class Press Key to enter the class Key to select a item Press Setting example Details of the Function Table Factory settings IntData output Time/Date output ID number output 5if Timeout AK, Error codeErCd Interface Ct5 Description of the Class Environment, Display Description of the Item Data Output Mode Key modeStream mode Auto print modes a and B Interval memory mode Description of the Item Data FormatStandard format DP Dump print format KF format MT formatNU numerical format Data Unit Terminator Stable value Unstable value CSV format Data numberDate Time Positive error Negative error SpaceData Format Examples Stable Unstable Overload Units Setting the time Clock and Calendar FunctionOperation Confirming the time Set the date Store Setting the dateQuitting the operation Setting the ID Number ID Number and GLP Report Key operation Calibration report using the internal massGLP Report Commad Calibration test report using an internal massBalance returns to weighing mode after this test Calibration report using an external weight Calibration test report using an external weight When using preset target value, proceed to step Weighing data Title block and end blockTitle block Returns to the weighing mode Data MemoryReleasing Clr or err Press and hold the Print key until the key Data Memory for Weighing Data Storing the weighing dataMemory full Interval memory Setting the function table Parameter settings for each output mode are as followsAdditional parameter settings, as follows Enabling the data memory function Deleting all memory data at one time Recalling the memory dataTransmitting all memory data at one time Data Memory for Calibration and Calibration Test Storing the calibration and calibration test dataTransmitting the memory data Deleting data stored in memory Underhook Density Measurement Formula to obtain the densityPrior to measurement Changing the function table Density of a liquid Relation between the water temperature and density Entering the density of a liquid Measuring the density Output or store Density display Turns off. lightsPress the modes Key to proceed to other Sub 25 pin assignments Standard Input and Output InterfaceRS-232C Interface Connection to Peripheral Equipment Connection to an AD-8121B printer Using Windows Communication Tools Software WinCT Using the WinCT software, the balance can do the followingConnection to a computer and the use of WinCT RsCom Commands Command List Settings Related to RS-232C Acknowledge Code and Error CodesControl Using CTS and RTS Command Re-zeroing the display Command ExamplesOn command turning on the balance CAL command Calibration with internal mass Error code Command ?PT command Net value Tare value Weighing with a tare Zero Command ExecutionPT command to set a target weight of 10 g Zero display Treatment of the Balance MaintenanceError Codes Sample mass error Unit mass errorAutomatic response adjustment zero error Automatic response adjustment unstable error Other Display Asking for Repair Checking the Balance Performance and EnvironmentChecking that the balance performs properly Specifications External Dimensions Unit mm Options and Peripheral Equipment GH-02 USB interfaceGH-08 Ethernet Interface AD-8121B Printer AD-1653 Density Determination Kit AD-1683 DC Static EliminatorAX-USB-9P-EX USB Converter 9970 g/cm3 AX-SW128 Foot switch AX-T-314A-S External key Plug Other options Terms/Index Terms Index Options 5pd Out5tart Tare PU5e Memo Memo