Weighing with a tare

This example uses "erCd 1" of "5if" so that the <AK> (06h) code is output.

Computer

Time

Balance

R command

Sets the display to zero

Command received

In process

Command completed

Zero display

Place a container

TR command

ＴＲ	Tares
	Command received
	In process
	Command completed
	Zero display

Scommand

Ｓ

Ｔ

，

＋

０

１

０

．

０

ｇ

?PT command

(Net value)

？

Ｐ

Ｔ

Ｐ

Ｔ

，

＋

０

１

２

．

３

４

５

６

ｇ

(Tare value)

Page 70

Image 70

A&D GH-120/GH-200/GH-300/GH-202/GH-252 manual Weighing with a tare, Command ?PT command Net value Tare value

Contents

GH-120 GH-200 GH-300 GH-202 GH-252 1WMPD4000891CPage Contents Underhook Density Measurement Interface And Communication Introduction About This Manual Compliance With FCC Rules FeaturesCompliance Compliance With EMC DirectivesPage Unpacking the Balance Installing the Balance PrecautionsBefore Use During Use Shock Power Supply After Use Display Display Symbols and Key OperationKey When pressed and released When pressed and held Key operation Weighing Units Units 101 00001 Examples Unit Display Gram Counting mode Pcs Percent mode Densitymode Press the PrintChanging the Units Balance displays Unit setting example Read . Display symbols and Key operation before operation Precautions for the weighing operationBasic Operation Gram Mode Weighing 01mg Dual RangeWeighing range Available minimum display 1mg Storing a sample unit mass Weighing input mode Counting Mode PCSCounting operation Counting mode using the Acai function Mark turns off after Unit mass is improved Repeat Storing the 100% reference mass Percent Mode %Selecting the percent mode Reading the percentage Automatic Response Adjustment Response AdjustmentAdvise Displayed, then release the key Manual Response AdjustmentKey until Press Key again quickly Calibration Calibration Group One-Touch Calibration Automatic self calibration due to changes in temperatureAutomatic Self Calibration Mark Calibration Test Using the Internal Mass Press and hold the CAL Key until is CC Calibration Using an External Weight Key ..............The key to store the new mass value Calibration Test Using an External WeightKey................. The key To cancel the operation Even if the AC adapter is removed, Correcting the Internal Mass Value Function Switch and Initialization Permit or Inhibit Initializing the Balance Press the Print key To cancel this operation, pressKey to display Setting the Function Table Display symbol and keys Function Table Key to select a class Press Setting procedureFunction table is displayed Press Key to enter the class Key to select a item Press Setting example Details of the Function Table Data output Time/Date output Factory settingsInt ID number output ErCd 5if TimeoutAK, Error code Interface Ct5 Description of the Class Environment, Display Stream mode Description of the Item Data Output ModeKey mode Auto print modes a and B Standard format Interval memory modeDescription of the Item Data Format DP Dump print format NU numerical format KF formatMT format Data Unit Terminator Stable value Unstable value Date CSV formatData number Time Data Format Examples Positive errorNegative error Space Stable Unstable Overload Units Operation Setting the timeClock and Calendar Function Confirming the time Quitting the operation Setting the dateSet the date Store Setting the ID Number ID Number and GLP Report GLP Report Calibration report using the internal massKey operation Balance returns to weighing mode after this test Calibration test report using an internal massCommad Calibration report using an external weight Calibration test report using an external weight When using preset target value, proceed to step Title block Title block and end blockWeighing data Releasing Clr or err Returns to the weighing modeData Memory Press and hold the Print key until the key Memory full Data Memory for Weighing DataStoring the weighing data Interval memory Additional parameter settings, as follows Setting the function tableParameter settings for each output mode are as follows Enabling the data memory function Transmitting all memory data at one time Recalling the memory dataDeleting all memory data at one time Transmitting the memory data Data Memory for Calibration and Calibration TestStoring the calibration and calibration test data Deleting data stored in memory Underhook Prior to measurement Changing the function table Density MeasurementFormula to obtain the density Density of a liquid Relation between the water temperature and density Entering the density of a liquid Press the modes Measuring the densityOutput or store Density display Turns off. lights Key to proceed to other RS-232C Interface Standard Input and Output InterfaceSub 25 pin assignments Connection to Peripheral Equipment Connection to an AD-8121B printer Connection to a computer and the use of WinCT Using Windows Communication Tools Software WinCTUsing the WinCT software, the balance can do the following RsCom Commands Command List Control Using CTS and RTS Acknowledge Code and Error CodesSettings Related to RS-232C On command turning on the balance Command ExamplesCommand Re-zeroing the display CAL command Calibration with internal mass Error code Command ?PT command Net value Tare value Weighing with a tare PT command to set a target weight of 10 g Zero display Command ExecutionZero Error Codes MaintenanceTreatment of the Balance Automatic response adjustment zero error Sample mass errorUnit mass error Automatic response adjustment unstable error Other Display Checking that the balance performs properly Checking the Balance Performance and EnvironmentAsking for Repair Specifications External Dimensions Unit mm GH-08 Ethernet Interface Options and Peripheral EquipmentGH-02 USB interface AD-8121B Printer AX-USB-9P-EX USB Converter AD-1653 Density Determination KitAD-1683 DC Static Eliminator 9970 g/cm3 AX-SW128 Foot switch AX-T-314A-S External key Plug Other options Terms/Index Terms Index 5tart Options5pd Out Tare PU5e Memo Memo