Static Multicast Routing Commands | Accton Technology ES4548D

57 Multicast Filtering Commands

Static Multicast Routing Commands

Table 57-4 Static Multicast Routing Commands

Command	Function	Mode	Page

ip igmp snooping vlan	Adds a multicast router port	GC	57-8
mrouter
show ip igmp snooping	Shows multicast router ports	PE	57-9
mrouter

ip igmp snooping vlan mrouter

This command statically configures a multicast router port. Use the no form to remove the configuration.

Syntax

[no] ip igmp snooping vlan vlan-idmrouter interface

•vlan-id- VLAN ID (Range: 1-4093)

•interface

•ethernet unit/port

-unit - Stack unit. (Range: Always 1)

-port - Port number. (Range: 1-24/48)

•port-channel channel-id(Range: 1-24)

Default Setting

No static multicast router ports are configured.

Command Mode

Global Configuration

Command Usage

Depending on your network connections, IGMP snooping may not always be able to locate the IGMP querier. Therefore, if the IGMP querier is a known multicast router/switch connected over the network to an interface (port or trunk) on your router, you can manually configure that interface to join all the current multicast groups.

Example

The following shows how to configure port 11 as a multicast router port within VLAN 1:

Console(config)#ip igmp snooping vlan 1 mrouter ethernet 1/11 Console(config)#

57-8

Image 516

Accton Technology ES4548D, ES4524D, 24/48-Port manual Static Multicast Routing Commands, Ip igmp snooping vlan mrouter

Contents

Powered by Accton Page ES4524D Gigabit Ethernet Switch ES4524D ES4548D F0.0.0.4 E112006-CS-R01 149100030400A Contents Setting the System Clock 10-1 Access Control Lists 15-1 Vii Vlan Configuration 23-1 Viii Multicast Filtering 28-1 File Management Commands 35-1 Smtp Alert Commands 38-1 802.1X Port Authentication 43-1 Xii Access Control List Commands 44-1 Xiii Address Table Commands 50-1 Xiv Private Vlan Commands 53-1 Quality of Service Commands 56-1 Xvi IPv4 Interface Commands 59-1 Xvii Xviii Tables XixPage Xxi Xxii Figures Xxiii Figures IP Filter 12-14 Port Security 13-2 Xxiv Figures Xxv Xxvi Section I Getting Started Getting Started Key Features Key FeaturesFeature Description Introduction Description of Software Features Introduction Description of Software Features Introduction Description of Software Features System Defaults System DefaultsFunction Parameter Default Password super View defaultview Snmp System Defaults Function Parameter Traffic Prioritization Ingress Port Priority Queue ModeDisabled Igmp Snooping Snooping Enabled System Log Status Enabled Messages Logged Initial Configuration Connecting to the SwitchConfiguration Options Required Connections Remote Connections Basic Configuration Setting PasswordsConsole Connection Setting an IP Address Assigning an IPv4 Address Assigning an IPv6 Address 45-159-1 59-2 60-4 60-10 60-3 60-12 Obtaining an IPv4 Address 59-359-4 35-2 Obtaining an IPv6 Address 60-2 Enabling Snmp Management Access 60-6 40-3 40-5 Managing System Files 40-1040-11 40-14 Saving Configuration Settings Initial Configuration Section II Switch Management Page Configuring the Switch Using the Web Interface Navigating the Web Browser Interface Home Web Page Configuration Buttons Panel DisplayApply Revert Help Action Switch Main Menu Description Main MenuSystem System Information IPv6 Neighbor 11-1 12-815-1 12-13 Lacp 17-1 Class-of-service value 23-1Current Table 23-5 26-9 28-2Query Multicast Router 28-4 Basic System Settings Displaying System InformationField Attributes System Information Displaying Switch Hardware/Software Versions CLI Specify the hostname, location and contact informationMain Board Management Software Switch Information 34-8 Displaying Bridge Extension Configuration Displaying Bridge Extension Capabilities Configuring Support for Jumbo Frames CLI Enter the following commandCommand Usage Command Attributes Resetting the System CLI Use the reload command to restart the switchRenumbering the Stack CLI This example renumbers all units in the stack Basic System Settings Setting an IP Address Setting the Switch’s IP Address IP Version Manual Configuration IPv4 Interface Configuration Manual Using DHCP/BOOTP IPv4 Interface Configuration Dhcp Configuring an IPv6 Address Setting the Switch’s IP Address IP Version 6 IP Address Setting the Switch’s IP Address IP Version 6 Current Address Table IPv6 Interface Configuration Configuring an IPv6 General Network Prefix 60-1360-14 IPv6 General Prefix Configuration Protocol Settings Current Neighbor Cache Table Adding Static Neighbors IPv6 Neighbor -- Add 60-22 60-26 Managing System Files Managing Firmware Downloading System Software from a Server Copy Firmware Deleting Files 35-7 Saving or Restoring Configuration Settings Downloading Configuration Settings from a Server Downloading Configuration Settings for Start-Up Console#copy tftp startup-config Console Port Settings 36-1 36-236-3 36-4 Telnet Settings Configuring the Telnet Interface Configuring Event Logging System Log ConfigurationError resource exhausted Logging Levels Remote Log Configuration 37-137-2 37-5 37-3 37-4 Displaying Log Messages Sending Simple Mail Transfer Protocol AlertsCLI This example shows the event message stored in RAM 37-7 Enabling and Configuring Smtp Alerts 38-1 38-238-3 38-4 Setting the System Clock Configuring Sntp Setting the Time Zone 39-139-3 39-2 Simple Network Management Protocol Snmp Overview Enabling the Snmp Agent SNMPv3 Security Models and LevelsLevel Group Read View Write View Notify View Security User defined Setting Community Access Strings CLI The following example enables Snmp on the switch40-2 Specifying Trap Managers and Trap Types 11-5 Configuring SNMPv3 Management Access 40-7 Setting a Local Engine ID Specifying a Remote Engine IDCLI This example sets an SNMPv3 engine ID 40-8 Configuring SNMPv3 Users CLI This example specifies a remote SNMPv3 engine ID Configuring SNMPv3 Users Configuring Remote SNMPv3 Users 40-15 Configuring Remote SNMPv3 Users Configuring SNMPv3 Groups Topology Change Timer immediately Any of its configured ports transitions fromThat its configuration may have been altered Authenticated. While all implementations Supported Notification Messages Configuring SNMPv3 Groups 40-13 Setting SNMPv3 Views Configuring SNMPv3 Views 11-17 Simple Network Management Protocol 11-18 User Authentication Configuring User Accounts Configuring Local/Remote Logon Authentication 41-1 Radius Settings Global Provides globally applicable Radius settingsWeb Telnet TACACS+ server Tacacs Settings Authentication Server Settings Configuring Https Replacing the Default Secure-site Certificate Copy Https Certificate Address server ip-address Configuring the Secure Shell Authenticating SSH v1.5 Clients Authenticating SSH v2 Clients Generating the Host Key Pair 41-20 41-2141-23 Configuring the SSH Server SSH server includes basic settings for authentication Filtering IP Addresses for Management Access 41-1741-18 41-19 41-24 41-25 Configuring Port Security Port Security 42-1 Configuring 802.1X Port Authentication Displaying 802.1X Global Settings 802.1X protocol provides port authenticationCLI This example shows the default global setting for Web Click Security, 802.1X, Information Configuring 802.1X Global Settings Configuring Port Settings forCLI This example enables 802.1X globally for the switch 43-1 802.1X Port Configuration Authorized 43-2 43-443-5 Displaying 802.1X Statistics 802.1X StatisticsParameter Description 802.1X Port Statistics CLI This example displays the dot1x statistics for port Configuring 802.1X Port Authentication 14-8 Access Control Lists Setting an ACL Name and TypeOverview Configuring a Standard IPv4 ACL CLI This example creates a standard IP ACL named bill44-2 Configuring an Extended IPv4 ACL ACL Configuration Standard IPv4 15-4 ACL Configuration Extended IPv4 44-3 Configuring a MAC ACL Configuring a Standard IPv6 ACL 44-13 Configuring an Extended IPv6 ACL 44-8 15-9 ACL Configuration Extended IPv6 44-9 Binding a Port to an Access Control List This switch supports ACLs for ingress filtering only44-6 44-15 Access Control Lists 15-12 Port Configuration Displaying Connection StatusField Attributes Web Configuration Field Attributes CLIBasic information Current status CLI This example shows the connection status for Port 45-8 Configuring Interface Connections 45-2 45-645-3 45-4 Showing Port Statistics Port Statistics Etherlike StatisticsRmon Statistics Formed Oversize FramesFragments 16-9 CLI This example shows statistics for port 45-9 Creating Trunk Groups Statically Configuring a Trunk Static Trunk Configuration Setting a Load-Balance Mode for Trunks 46-2 Trunk Load Balance Mode Enabling Lacp on Selected Ports 46-346-11 Lacp Trunk Configuration 46-4 Configuring Lacp Parameters Dynamically Creating a Port Channel Lacp Aggregation Port Displaying Lacp Port Counters You can display statistics for Lacp protocol messagesLacp Port Counters Parameter Description Marker Unknown Pkts TypeMarker Illegal Pkts Badly formed PDU or an illegal value of Protocol Subtype Displaying Lacp Settings and Status for the Local Side Lacp Internal Configuration InformationField Description Lacp Port Internal Information Displaying Lacp Settings and Status for the Remote Side Lacp Neighbor Configuration Information Field Description 17-14 Setting Broadcast Storm Thresholds Broadcast Storm Control 47-1 45-10 Configuring Port Mirroring Mirror Port Configuration 48-1 Configuring Rate Limits Command Attribute 49-1 Address Table Settings Setting Static Addresses Displaying the Address Table 50-1 Dynamic Addresses 50-3 Changing the Aging Time CLI This example sets the aging time to 400 seconds50-4 Spanning Tree Algorithm Configuration Region R For this Region Displaying Global Settings 22-4 Web Click Spanning Tree, STA, Information STA Information Configuring Global Settings Global settings apply to the entire switch Basic Configuration of Global Settings Root Device Configuration Configuration Settings for Rstp Configuration Settings for Mstp STA Global Configuration Displaying Interface Settings 22-11 STA Port Information Configuring Interface Settings CLI This example shows the STA attributes for port51-18 22-14 Configuring Multiple Spanning Trees CLI This example sets STA attributes for port Mstp Vlan Configuration 51-8 Displaying Interface Settings for Mstp Mstp Port Information Configuring Interface Settings for Mstp CLI This example sets the Mstp attributes for port 51-16 Vlan Configuration Assigning Ports to VLANs 23-2 Forwarding Tagged/Untagged Frames Enabling or Disabling Gvrp Global Setting CLI This example enables Gvrp for the switchDisplaying Basic Vlan Information Command Attributes Web Displaying Current VLANsMax support Vlan numbers 256 Max support Vlan ID 4093 Command Attributes CLI Creating VLANs52-17 Adding Static Members to VLANs Vlan Index CLI This example creates a new Vlan52-5 52-6 Vlan Static Table Adding Static Members Adding Static Members to VLANs Port Index 52-11 Configuring Vlan Behavior for Interfaces Vlan Port Configuration Configuring Ieee 802.1Q Tunneling Layer 2 Flow for Packets Coming into a Tunnel Access Port QinQ Tunneling Layer 2 Flow for Packets Coming into a Tunnel Uplink Port Configuration Limitations for QinQ General Configuration Guidelines for QinQ Enabling QinQ Tunneling on the Switch CLI This example sets the switch to operate in QinQ mode52-14 52-16 Adding an Interface to a QinQ Tunnel Tunnel Port Configuration 52-15 Configuring Private VLANs CLI This example enables private VLANsEnabling Private VLANs 53-1 Configuring Uplink and Downlink Ports 53-2 Configuring Protocol-Based VLANs Configuring Protocol GroupsCreate a protocol group for one or more protocols Mapping Protocols to VLANs 54-1 Protocol Vlan Port Configuration 54-2 Configuring Protocol-Based VLANs 25-4 Class of Service Configuration Layer 2 Queue SettingsSetting the Default Priority for Interfaces CLI This example assigns a default priority of 5 to port 55-3 Mapping CoS Values to Egress Queues Mapping CoS Values to Egress QueuesCoS Priority Levels Priority Level Traffic Type Selecting the Queue Mode 55-455-6 Setting the Service Weight for Traffic Classes 55-255-5 Queue Scheduling Layer 3/4 Priority Settings Mapping Layer 3/4 Priorities to CoS ValuesSelecting IP Precedence/DSCP Priority 55-8 Mapping IP Precedence Mapping IP Precedence Priority Level Traffic Type Mapping Dscp Priority Mapping Dscp Priority IP Dscp Value CoS Value10, 12, 14 18, 20, 22 26, 28, 30, 32, 34 38, 40 55-10 55-13 Mapping IP Port Priority IP Port Priority Status 55-11 Quality of Service Configuring Quality of Service Parameters Configuring a Class Map Class ConfigurationMatch Class Settings Class map is used for matching packets to a specified class Configuring Class Maps Creating QoS Policies Policy Map56-2 56-3 Policy Configuration Policy Rule Settings Class SettingsPolicy Options Configuring Policy Maps Attaching a Policy Map to Ingress Queues 56-456-5 56-6 Quality of Service 27-8 Multicast Filtering Layer 2 Igmp Snooping and Query Configuring Igmp Snooping and Query Parameters 57-1 57-457-5 57-6 Displaying Interfaces Attached to a Multicast Router 57-9 Specifying Static Interfaces for a Multicast Router 57-8 Displaying Port Members of Multicast Services IP Multicast Registration Table Assigning Ports to Multicast Services Igmp Member Port Table 28-8 Configuring Domain Name Service Configuring General DNS Service Parameters 58-3 58-458-5 58-7 Configuring Static DNS Host to Address Entries 58-1 58-6 Displaying the DNS Cache DNS Cache 29-6 Switch Clustering Cluster Configuration Cluster Member Configuration Web Click Cluster, ConfigurationAdds Candidate switches to the cluster as Members 61-1 Web Click Cluster, Member Configuration Displays current cluster Member switch informationCluster Member Information 61-3 Cluster Candidate Information 61-5 Section IIICommand Line Interface Page Using the Command Line Interface Accessing the CLITelnet Connection 31-2 Entering Commands Command CompletionGetting Help on Commands Keywords and Arguments Showing Commands Negating the Effect of Commands Using Command HistoryPartial Keyword Lookup Understanding Command Modes Exec CommandsGeneral Command Modes Configuration Commands Configuration Command Modes Prompt Consoleconfig-if# 45-1 Command Line Processing Keystroke CommandsKeystroke Function Using the Command Line Interface 31-10 CLI Command Groups Command Group Index Description Class of Service 55-157-1 General Commands Enable Disable ConfigureRelated Commands Example Show history Normal Exec, Privileged Exec Prompt EndExit Syntax Prompt string no prompt This command exits the configuration program This example shows how to quit a CLI sessionQuit General Commands 33-6 System Management Commands System Management Commands Function ModeHostname Syntax Hostname name no hostname Switch renumber Syntax Switch all renumber Default SettingReload Show startup-config Syntax No jumbo frame Default SettingJumbo frame Show ipv6 mtu 34-4 Show running-config Show running-config34-5 Show startup-config34-3 This command displays system information Show systemShow users Show version 34-9 System Management Commands 34-10 File Management Commands Saving or Restoring Configuration SettingsFlash/File Commands Function Mode Managing Firmware Copy 35-3 This command deletes a file or image DeleteSyntax Delete unit filename This command displays a list of files in flash memory Syntax Dir unit boot-rom config opcode filenameDir Dir Delete public-key41-20 Whichboot Syntax whichboot unitFile Directory Information Column Heading Description Boot system Syntax Boot system unit boot-romconfig opcode filenameDir 35-5 whichboot File Management Commands 35-8 Line Commands Line Commands Function ModeLine Syntax Line console vty Login Syntax Login local no login Password Username 41-1 passwordSyntax Password 0 7 password no password No password is specified Timeout login response Exec-timeoutSyntax Exec-timeout seconds no exec-timeout Password-thresh CLI No timeout Telnet 10 minutesSyntax Password-thresh threshold no password-thresh Default value is three attempts Silent-time DatabitsSyntax Silent-time seconds no silent-time Syntax Databits 7 8 no databits Parity Syntax Parity none even odd no parity Speed StopbitsSyntax Speed bps no speed Syntax Stopbits 1 Disconnect Show lineSyntax Disconnect session-id Syntax Show line console vty To show all lines, enter this command Event Logging Commands Event Logging Commands Function ModeSyntax No logging on Default Setting Logging on Flash errors level 3 RAM warnings level 7 Logging historyLogging history 37-2 logging trap 37-4 clear log Default Setting Command Mode Logging hostLogging facility Syntax No logging host hostipaddress Disabled Level 7 Logging trapSyntax Logging trap level no logging trap Clear log Show loggingSyntax Clear log flash ram Syntax Show logging flash ram sendmail trap Logging facility command Show logging flash/ram display descriptionShow logging trap display description Show log Syntax Show log flash ramFollowing example shows the event message stored in RAM Event Logging Commands 37-8 Smtp Alert Commands Smtp Alert Commands Function ModeLogging sendmail host 38-4 Logging sendmail level Logging sendmail source-emailSyntax Logging sendmail level level Syntax Logging sendmail source-email email-address Syntax No logging sendmail Default Setting Logging sendmail destination-emailLogging sendmail Syntax No logging sendmail destination-email email-address Show logging sendmail Time Commands Time Commands Function ModeSyntax No sntp client Default Setting Sntp client Sntp server Sntp server 39-2 sntp poll 39-3 show sntpSyntax Sntp server ip1 ip2 ip3 Sntp poll Show sntpSntp client 39-1 sntp poll 39-3 show sntp Syntax Sntp poll seconds no sntp poll Clock timezone This command displays the system clock Calendar setShow calendar Calendar set hour min sec day month year month day year Time Commands 39-6 Snmp Commands Snmp Commands Function Mode Syntax No snmp-server Default Setting Snmp-serverShow snmp Snmp-server community Snmp-server contact Snmp-server locationSyntax Snmp-server contact string no snmp-server contact Syntax Snmp-server location text no snmp-server location Snmp-server host Host Address None Notification Type Traps Snmp Version UDP Port Snmp-server enable traps Snmp-server enable trapsIssue authentication and link-up-down traps Snmp-server engine-id This command shows the Snmp engine ID This example shows the default engine IDShow snmp engine-id Defaultview includes access to the entire MIB tree Snmp-server viewExamples This view includes MIB-2 This command shows information on the Snmp views Show snmp viewSnmp-server group Show snmp view display description 40-12 Show snmp group Show snmp group display descriptionField Description Groupname Name of an Snmp group Snmp-server user This command shows information on Snmp users Show snmp user Show snmp user display description User Authentication Commands User Account CommandsAuthentication Commands Command Group Function User Access Commands Function Mode Enable password Default Login Settings Username Access-level PasswordGuest Admin Authentication Sequence Authentication loginAuthentication Sequence Commands Function Mode Authentication enable Tacacs Use Tacacs server passwordUsername for setting the local user names and passwords Local Radius Client Commands Function Mode Show radius-server Shows the current Radius settings 41-8Radius Client 41-8 Default Setting Auth-port Retransmit Command ModeRadius-server host Radius-server port Radius-server key Radius-server retransmitSyntax Radius-server key keystring no radius-server key Radius-server timeout Show radius-server TACACS+ Client Commands Function Mode TACACS+ ClientTacacs-server host Tacacs-server port Tacacs-server key Show tacacs-serverSyntax Tacacs-server key keystring no tacacs-server key Web Server Commands Ip http portIp http server Syntax No ip http secure-server Default Setting Ip http secure-serverIp http port Ip http secure-port Ip http secure-port41-13copy tftp https-certificatePortnumber The UDP port used for HTTPS. Range Telnet Server Commands Telnet Server Commands Function ModeIp telnet server Secure Shell Commands 10 Secure Shell Commands Function ModeConfiguration Guidelines Sets the SSH server key size 41-19 Copy tftp public-key 41-16 Syntax No ip ssh server Default Setting Ip ssh server Ip ssh timeout Syntax Ip ssh timeout seconds no ip ssh timeoutExec-timeout36-4 show ip ssh Ip ssh crypto host-key generate 41-20 show ssh Ip ssh authentication-retries Ip ssh server-key sizeKey-size- The size of server key. Range 512-896 bits Bits Delete public-key Ip ssh crypto host-key generateSyntax Delete public-key username dsa rsa Syntax Ip ssh crypto host-key generate dsa rsa Ip ssh crypto zeroize Ip ssh save host-keySyntax Ip ssh crypto zeroize dsa rsa Syntax Ip ssh save host-key dsa rsa This command displays the current SSH server connections Show ip sshShow ssh Ip ssh crypto host-key generate Show public-key TerminologySyntax Show public-key user username host IP Filter Commands 12 IP Filter Commands Function ModeManagement 41-25 Show management 41-26 Port Security Commands Port Security Commands Function ModePort security Max-mac-count Shutdown 45-6mac-address-table static 802.1X Port Authentication 802.1X Port Authentication Commands Function ModeSyntax No dot1x system-auth-control Default Setting Dot1x system-auth-control Dot1x default Default Command ModeDot1x max-req Dot1x port-control Dot1x operation-mode Force-authorizedSingle-host Dot1x re-authenticate Dot1x re-authenticationSyntax Dot1x re-authenticate interface Syntax No dot1x re-authentication Command Mode Dot1x timeout quiet-period Dot1x timeout re-authperiodDot1x timeout re-authperiod43-5 Seconds The number of seconds. Range Dot1x timeout tx-period Show dot1xSyntax Show dot1x statistics interface interface Statistics Displays dot1x status for each port Interface Authenticator State Machine Backend State Machine Reauthentication State Machine State- Current state including initialize, reauthenticate Access Control List Commands Access Control List Commands Command Groups FunctionIPv4 ACL Commands Function Mode IPv4 ACLs Access-list ip Syntax No access-list ip standard extended aclnamePermit, deny Ip access-group44-6 show ip access-list44-5 Syntax No permit deny any source bitmask host source Access-list ip Standard IPv4 ACLNo permit deny tcp Extended IPv4 ACL Show ip access-list This command displays the rules for configured IPv4 ACLsSyntax Show ip access-list standard extended aclname Permit, deny Ip access-group44-6 Ip access-group Show ip access-groupSyntax No ip access-group aclname Show ip access-list44-5 Access-list ipv6 IPv6 ACL Commands Function ModeSyntax No access-list ipv6 standard extended aclname IPv6 ACLs Access-list ipv6 Standard IPv6 ACLNew rules are appended to the end of the list Syntax No permit deny Any destination-ipv6-address/prefix-lengthNext-header next-header dscp dscp flow-label flow-label Extended IPv6 ACL Show ipv6 access-list This command displays the rules for configured IPv6 ACLs Ipv6 access-group Show ipv6 access-groupSyntax No ipv6 access-group aclname Access-list mac MAC ACL Commands Function ModeSyntax No access-list mac aclname MAC ACLs Permit, deny MAC ACL No permit deny tagged-eth2No permit deny untagged-eth2 No permit deny tagged-802.3 Show mac access-list This command displays the rules for configured MAC ACLsSyntax Show mac access-list aclname Mac access-group Show mac access-groupSyntax Mac access-group aclname Show access-list Show access-groupACL Information Commands Function Mode ACL Information 44-17 Access Control List Commands 44-18 Interface Commands Interface Commands Function ModeInterface Port-channel channel-idRange Description Speed-duplexSyntax Description string no description Syntax No negotiation Default Setting NegotiationNegotiation 45-3 capabilities Following example configures port 11 to use autonegotiation CapabilitiesCapabilities 45-4speed-duplex45-2 Syntax No flowcontrol Default Setting Following example enables flow control on portFlowcontrol Negotiation 45-3speed-duplex45-2 flowcontrol Syntax Media-type mode no media-type Syntax No shutdown Default SettingMedia-type Shutdown Port-channel channel-idRange Default Setting Clear countersSyntax Clear counters interface This command displays the status for an interface Show interfaces statusSyntax Show interfaces status interface Shows the status for all interfaces This command displays interface statistics Show interfaces countersSyntax Show interfaces counters interface Shows the counters for all interfaces Show interfaces switchport Syntax Show interfaces switchport interfaceShow interfaces switchport display description Indicates membership mode as Trunk or Hybrid Indicates the default priority for untagged framesAllowed Vlan Indicates tagged Interface Commands 45-12 Link Aggregation Commands Link Aggregation CommandsGuidelines for Creating Trunks Channel-group Dynamically Creating a Port ChannelSyntax Channel-group channel-idno channel-group Port channel load-balance Src-dst-ip Syntax No lacp Default Setting Lacp Lacp system-priority 32768 Lacp admin-keyEthernet Interface Lacp admin-key Port Channel Syntax Lacp admin-key key no lacp admin-keyInterface Configuration Port Channel This command displays Lacp information Lacp port-priorityShow lacp Port Channel all Show lacp counters display descriptionType LACPDUs Illegal Pkts Show lacp internal display description Show lacp neighbors display description Show port-channel load-balance Show lacp sysid display description 46-12 Broadcast Storm Control Commands Switchport broadcast packet-rateBroadcast Storm Control Commands Function Mode Enabled for all ports Packet-rate limit 500 pps Broadcast Storm Control Commands 47-2 Mirror Port Commands Mirror Port Commands Function ModeInterface Configuration Ethernet, destination port Port monitor This command displays mirror information Following shows mirroring configured from port 6 to portShow port monitor Syntax Show port monitor interface Rate Limit Commands Rate Limit Commands Function ModeRate-limit Gigabit Ethernet 1000 Mbps Rate Limit Commands 49-2 Address Table Commands Address Table Commands Function ModeMac-address-table static Action Clear mac-address-table dynamic Show mac-address-table Mac-address- MAC address Mask Bits to match in the addressShow ipv6 neighbors Mac-address-table aging-time Show mac-address-table aging-time Spanning Tree Commands Spanning Tree Commands Function Mode Spanning-tree mode Syntax No spanning-tree Default SettingSpanning tree is enabled Spanning-tree Spanning-tree forward-time Spanning-tree forward-time Spanning-tree hello-time Spanning-tree forward-time 51-3spanning-tree max-age Spanning-tree max-age Spanning-tree prioritySpanning-tree forward-time 51-3spanning-tree hello-time Spanning-tree pathcost method Long method Spanning-tree mst-configuration This command limits the maximum transmission rate for BPDUsSpanning-tree transmission-limit Count The transmission limit in seconds. Range MST Configuration Mst vlanNo mst instanceid vlan vlan-range Mst priority NameMst instanceid priority priority no mst instanceid priority Syntax Name name Revision Syntax Revision numberNumber Revision number of the spanning tree. Range Name Spanning-tree spanning-disabled Syntax No spanning-tree spanning-disabled Default SettingThis example disables the spanning tree algorithm for port Max-hops Spanning-tree cost Syntax Spanning-tree cost cost no spanning-tree cost Syntax No spanning-tree edge-port Default Setting Spanning-tree port-prioritySpanning-tree edge-port Priority The priority for a port. Range 0-240, in steps Syntax No spanning-tree portfast Default Setting Spanning-tree portfast Spanning-tree link-type Spanning-treeedge-port51-13 Spanning-tree mst cost Spanning-tree mst port-priority51-17 Spanning-tree mst port-priority Spanning-tree protocol-migrationSyntax Spanning-tree protocol-migration interface Show spanning-tree Syntax Show spanning-tree interface mst instanceid 51-19 Show spanning-tree mst configuration Vlan Commands Gvrp and Bridge Extension CommandsVlan Commands Command Groups Function Gvrp and Bridge Extension Commands Function Mode Syntax No bridge-ext gvrp Default Setting Bridge-ext gvrpShow bridge-ext Switchport gvrp Show gvrp configurationSyntax No switchport gvrp Default Setting Syntax Show gvrp configuration interface Garp timer Show garp timer Syntax Show garp timer interfaceCommands for Editing Vlan Groups Function Mode Editing Vlan Groups By default only Vlan 1 exists and is active Vlan Database ConfigurationVlan Show vlan Configuring Vlan Interfaces Commands for Configuring Vlan Interfaces Function ModeInterface vlan Interface vlan Switchport mode Syntax Switchport mode hybrid trunk no switchport modeAll ports are in hybrid mode with the Pvid set to Vlan Switchport acceptable-frame-types52-9 Switchport acceptable-frame-types Switchport ingress-filteringSwitchport mode Syntax No switchport ingress-filtering Default Setting Switchport native vlan Switchport allowed vlan Switchport forbidden vlan No VLANs are included in the forbidden list Ieee 802.1Q Tunneling Commands Function Mode General Configuration Guidelines for QinQDot1q-tunnel 52-14 Syntax No dot1q-tunnel system-tunnel-control Default Setting Show dot1q-tunnel52-16 Show interfaces switchport Switchport dot1q-tunnel tpid 0x8100 Commands for Displaying Vlan Information Function Mode Displaying Vlan Information This command shows Vlan information Following example shows how to display information for VlanShow vlan Syntax Show vlan id vlan-idname vlan-name Vlan Commands 52-18 Private Vlan Commands Private Vlan Commands Function ModePvlan No private VLANs are defined This command displays the configured private Vlan Show pvlan Protocol-based Vlan Commands Protocol-vlan protocol-group Configuring GroupsProtocol-based Vlan Commands Function Mode 54-4 Protocol-vlan protocol-group Configuring No protocol groups are configuredNo protocol groups are mapped for any interface This shows protocol group 1 configured for IP over Ethernet Show protocol-vlan protocol-groupSyntax Show protocol-vlan protocol-group group-id Group-id- Group identifier for a protocol group. Range Show interfaces protocol-vlan protocol-group Mapping for all interfaces is displayed Class of Service Commands Priority Commands LayerPriority Commands Command Groups Function Priority Commands Layer Function Mode Queue mode Syntax Queue mode strict wrr no queue modeWeighted Round Robin Queue bandwidth 55-4 show queue mode Switchport priority default Queue bandwidth weight1...weight4 no queue bandwidth Queue bandwidthQueue cos-map Queue cos-mapqueueid cos1 ... cosn no queue cos-map Show queue mode Default CoS Priority LevelsThis command shows the current queue mode Show queue cos-map55-6 This command shows the class of service priority map Show queue bandwidthShow queue cos-map Syntax Show queue cos-map interface Priority Commands Layer 3 Priority Commands Layer 3 Function ModeSyntax No map ip port Default Setting Following example shows how to map Http traffic to CoS value Syntax No map ip precedence Default Setting Map ip precedence Interface Configuration List below shows the default priority mapping Syntax No map ip dscp Default Setting Map ip dscp dscp-value cos cos-value no map ip dscp This command shows the IP port priority map Show map ip portMapping IP Dscp to CoS Values IP Dscp Value Syntax Show map ip port interface This command shows the IP precedence priority map Show map ip precedenceSyntax Show map ip precedence interface This command shows the IP Dscp priority map Show map ip dscpSyntax Show map ip dscp interface 55-14 Quality of Service Commands Quality of Service Commands Function Mode Class-map Syntax No class-map class-map-namematch-anyShow class map Class Map Configuration Match Policy-map ClassNo policy-mappolicy-map-name No class class-map-name Policy Map Configuration Set Policy Map Class Configuration PoliceSyntax No police rate-kbpsburst-byteexceed-action drop set Drop out-of-profile packets Service-policy Syntax No service-policy input policy-map-nameNo policy map is attached to an interface Show class-map Show policy-mapSyntax Show class-map class-map-name Show policy-mappolicy-map-name class class-map-name Port-channel channel-idRange Command Mode Show policy-map interfaceSyntax Show policy-map interface interface input Quality of Service Commands 56-10 Multicast Filtering Commands Igmp Snooping CommandsIp igmp snooping Ip igmp snooping vlan static Ip igmp snooping versionIgmp Version Show ip igmp snooping Show mac-address-table multicast Igmp Query Commands Igmp Query Commands Function ModeSyntax No ip igmp snooping querier Default Setting Ip igmp snooping querier Following shows how to configure the query count to Ip igmp snooping query-countIp igmp snooping query-interval Times Seconds The report delay advertised in Igmp queries. Range Ip igmp snooping query-max-response-time Switch must use IGMPv2 for this command to take effect Ip igmp snooping router-port-expire-time Static Multicast Routing Commands Static Multicast Routing Commands Function ModeNo static multicast router ports are configured Ip igmp snooping vlan mrouter Displays multicast router ports for all configured VLANs Show ip igmp snooping mrouter Multicast Filtering Commands 57-10 Domain Name Service Commands DNS Commands Function ModeIp host No ip host name address1 address2 … address8 This command deletes entries from the DNS table Clear hostThis example maps two address to a host name Syntax Clear host name Ip domain-name Ip domain-listSyntax Ip domain-name name no ip domain-name Ip domain-list58-3 ip name-server58-4 ip domain-lookup58-5 Ip name-server Ip domain-name58-3Server-address1- IP address of domain-name server Syntax No ip domain-lookup Default Setting Ip domain-lookupIp domain-name58-3 ip domain-lookup58-5 Show hosts Ip domain-name58-3 ip name-server58-4 Show dns Show dns cacheShow dns cache display description This command clears all entries in the DNS cache Clear dns cache IPv4 Interface Commands IPv4 Configuration Commands Function ModeIp address Ip default-gateway Syntax Ip default-gateway gateway no ip default-gatewayGateway IP address of the default gateway Ip dhcp restart 59-3 ipv6 address Following example defines a default gateway for this device Show ip redirects 59-4 ipv6 default-gateway60-12This command submits an IPv4 Bootp or Dhcp client request Ip dhcp restart This command displays the settings of an IPv4 interface Ip default-gateway59-2 Show ipv6 default-gateway60-12Show ip interface Show ip redirects This command has no default for the host PingSyntax Ping host count countsize size Interface 45-1 ping ipv6 59 IPv4 Interface Commands 59-6 IPv6 Interface Commands IPv6 Configuration Commands Ipv6 enable Syntax No ipv6 enable Default SettingIPv6 is disabled Ipv6 address link-local60-9 show ipv6 interface Ipv6 general-prefix No general prefix is definedShow ipv6 general-prefix60-4 This command displays all configured IPv6 general prefixes Show ipv6 general-prefixIpv6 address No IPv6 addresses are defined 60-5 Ipv6 address autoconfig Syntax No ipv6 address autoconfig Default Setting Ipv6 address eui-64 Ipv6 address Show ipv6 interface Ipv6 address autoconfig 60-6 show ipv6 interface Ipv6 address link-local Ipv6 enable Show ipv6 interface Show ipv6 interfaceShow ipv6 interface display description Field Show ipv6 interface display description FF022, and solicited nodes FF021FFXXXXXX as described belowAppending those bits to the prefix Maximum transmission unit for this interface Ipv6 default-gateway Show ipv6 default-gatewaySyntax Ipv6 default-gateway ipv6-addressno ipv6 address Ipv6 mtu Syntax Ipv6 mtu size no ipv6 mtu Show ipv6 mtu Show ipv6 trafficFollowing example shows the MTU cache for this device Show ipv6 mtu display description 60-15 Received in error Format errorsErrors discovered in processing their IPv6 options, etc Ipv6 rcvd Rcvd total Show ipv6 traffic display description Ipv6 sent Checksum errors Ipv6 icmp input InputInput interface for the messages Prohibited messages received by the interface Ipv6 icmp output Clear ipv6 traffic Repeat 5 timeout 2 seconds Ping ipv6 Ipv6 neighbor Ipv6 nd dad attempts Show ipv6 neighbors 60-26mac-address-table staticSyntax Ipv6 nd dad attempts count no ipv6 nd dad attempts Ipv6 nd ns interval 60-25 show ipv6 neighbors Ipv6 nd ns interval Milliseconds is used for neighbor discovery operations Show ipv6 neighbors Syntax Show ipv6 neighbors vlan vlan-id ipv6-addressShow ipv6 neighbors display description Field Description Clear ipv6 neighbors Show ipv6 neighbors display description 60 IPv6 Interface Commands 60-28 Switch Cluster Commands Switch Cluster Commands Function ModeSyntax No cluster Default Setting Cluster Cluster commander Syntax No cluster commander Default SettingCluster ip-pool Syntax Cluster ip-pool ip-addressno cluster ip-pool Cluster member No Members Rcommand Syntax Rcommand id member-idMember-id- The ID number of the Member switch. Range This command shows the switch clustering configuration This command shows the current switch cluster members Show cluster membersShow cluster candidates Switch Cluster Commands 61-6 Section IVAppendices Appendices Appendix a Software Specifications Software Features Management Features Groups 1, 2, 3, 9 Statistics, History, Alarm, EventStandards Icmp RFC Igmp RFC Management Information Bases Management Information Bases a Software Specifications Appendix B Troubleshooting Problems Accessing the Management InterfaceTable B-1 Troubleshooting Chart Symptom Action Using System Logs Access Control List ACL Glossary Extended Universal Identifier EUI See Generic Attribute Registration Protocol Ieee 802.1Q Defines frame extensions for Vlan tagging IP Precedence See Port Trunk Port Mirroring See Ieee Secure Shell SSH TCP/IP protocol commonly used for software downloads User Datagram Protocol UDP Glossary Glossary-8 Index Numerics Index-2 Index-3 Index-4 Page ES4524D ES4548D E112006-CS-R01 149100030400A