Unhooking the power switch shaft | Agilent Technologies 54622D

Replacing Assemblies

To remove the power supply

5Use a flat-blade screwdriver to gently unhook the latch that holds the white power-actuator shaft to the power switch, then disconnect the shaft from the power switch. After you disconnect the shaft, make sure you position it in the recess along the side of the display bracket.

Figure 6-10

Gently apply outward( pressure at this corner

of the slot

Unhooking the power switch shaft

6-13

Image 97

Agilent Technologies 54622D, 54624A, 54621D, 54622A, 54621A manual Unhooking the power switch shaft

Contents

Agilent 54621D/22D Mixed-Signal Oscilloscope Horizontal Controls select sweep speed and delay parameters Display shows current input signalsSoftkeys extend the functionality of command keys Utilities This Book Contents Troubleshooting the Oscilloscope Solving General Problems with the OscilloscopesContents General Information General Information To inspect package contents General Information Package contents for 54620-Series Oscilloscopes Option Description To inspect options and accessories Model Description Accessories available Plug Type Cable Part Number Power Cords Acquisition Analog Channels Performance CharacteristicsAcquisition Digital Channels on 54621D and 54622D only Probe ID Agilent/HP Auto probe sense Tek Compatible Vertical System Analog Channels Accuracy = ±2.0%80 mV + 0.4%80 mV = ±1.92 mV Vertical System Digital Channels 54621D and 54622D only Sample rate of 200/400 MSa/s Horizontal Can Trigger System Digital D15 D0 Channel Triggering 54621D and 5462 2D Analog Channel TriggeringExternal EXT Triggering Display System Measurement Features Storage FFT Power Requirements General Characteristics Preparing the Oscilloscope for Use Preparing the Oscilloscope for Use Setting up the Oscilloscope To adjust the handle To adjust the handle Press the power switch To power-on the oscilloscopeTo power-on the oscilloscope To adjust the display intensity To adjust the display intensityIntensity control To compensate your probe To connect the oscilloscope probesTo connect the oscilloscope probes Press Autoscale To use the digital probes mixed-signal oscilloscope only To use the digital probes mixed-signal oscilloscope only Grabber Signal Lead Ground Lead Grabber Signals Ground To connect an RS-232 cable To connect a printerTo connect a printer Press the Autoscale key on the front panel To verify basic oscilloscope operationTo verify basic oscilloscope operation Verifying Basic Oscilloscope Operation Getting started using the oscilloscope interface To verify basic oscilloscope operation Using Quick Help Preparing the Oscilloscope for Use Loading a language from floppy disk Loading a language from floppy disk Disconnect power from the instrument Cleaning the oscilloscope Testing Performance If a performance test fails Testing Performance List of Test Equipment Equipment Critical SpecificationsList of Test Equipment Part Number To construct the test connector To construct the test connectorMaterials Required to Construct the Test Connectors Constructing the 8-by-2 Connector Press the Autoscale key To test the 54621D/22D Oscilloscope digital channelsTo test the 54621D/22D Oscilloscope digital channels To verify digital channel threshold accuracy To verify digital channel threshold accuracy Method 1 Using the Test Connector Method 2 Using the Test Fixture Threshold voltage setting DC offset voltage setting Limits Threshold Accuracy Voltage Test Settings Equipment Critical Specifications Recommended Model/Part Set up the oscilloscopeTo verify voltage measurement accuracy To verify voltage measurement accuracy MV/Div 616 mV 384 mV Settings Used to Verify Voltage Measurement Accuracy Use a Blocking Capacitor to Reduce Noise Using a Blocking Capacitor to Reduce Noise To verify bandwidth To verify bandwidthEquipment Required to Verify Bandwidth Signal Generator Frequency Setting Calculate the response using this formulaChange the time base to 5 ns/div Selected Channel 54621A/21D 54622A/22D 54624A To verify horizontal Dt and 1/Dt accuracy To verify horizontal ∆t and 1/∆t accuracy 54622A/22D/24A only Measure the following54621A and 54621D only To verify trigger sensitivity To verify trigger sensitivityEquipment Required to Verify Trigger Sensitivity Test Internal Trigger Sensitivity Test External Trigger Sensitivity Agilent 54622A/22D/24A Performance Test Record Agilent 54621A/54621D Agilent 54621A/21D Performance Test Record Calibrating and Adjusting Calibrating and Adjusting Hazardous Voltages Prepare the oscilloscope for the voltage adjustment To adjust the power supplyTo adjust the power supply Digital multimeter Supply Voltage Tolerance Power Supply Voltage Tolerances +3.3V Adjustment To perform User Cal To perform User Cal To adjust the oscilloscope display To adjust the oscilloscope displayWhen to Adjust the Oscilloscope Display Do not adjust Sub Bri or Cont controls 96,= Troubleshooting Read All Cautions and Warnings Troubleshooting If there is no trace display Solving General Problems with the Oscilloscopes If the trace display is unusual or unexpected If the trace display is unusual or unexpected If you cannot see a channel If you cannot see a channel Equipment Required to Troubleshoot the Oscilloscope Troubleshooting the Oscilloscope Location of the Low Voltage Power Supply Connectors Connector Load Amps Resistor WattsTo construct your own dummy load To construct your own dummy load To check out the oscilloscope Connect the power cord, then turn on the oscilloscopeTo check out the oscilloscope Low Voltage Power Supply Tolerances Display Signals on the System Board All OscilloscopesSignal Name Frequency Pulse Width Voltage Is the fan running? Location of the Fan Connector To check the Low Voltage Power Supply To check the Low Voltage Power SupplyLow Voltage Power Supply Test Points Beware of Hazardous Voltages If the Fuse is Blown To run the internal self-tests To run the internal self-tests Replacing Assemblies Replacing Assemblies Avoid Electrical Shock To remove the cabinet To remove the cabinetRemoving the cabinet To remove the fan To remove the fanRemoving the fan To remove the floppy drive To remove the floppy driveRemoving the floppy drive To remove the front panel To remove the front panelRemoving the intensity shaft and front panel To remove the display To remove the displayRemoving the display Unhooking the power switch shaft To remove the system board To remove the system boardPreparing to remove the system board Removing the system board To remove the power supply To remove the power supplyDisconnecting ground wire and ribbon cable Unhooking the power switch shaft Removing the power supply Lift the keyboard assembly straight out To remove the keyboard assemblyTo remove the keyboard assembly Removing the keyboard assembly To remove the handle To remove the handle Replaceable Parts Replaceable Parts To order a replacement part To order a replacement part Exploded View of the 54621A/22A/24A/21D/22D Oscilloscope Reference Agilent Part Qty Description Designator Number To order a replacement part Replaceable Parts MP1 Probes Option Accessory pouch and front-panel coverInput Cable 54621D/22D only Manufacturer’s Address Manufacturer’s NameProduct Name Model Numbers Product Regulations SafetySound Pressure Level Regulatory Information for Canada Safety Agilent Technologies, Inc Document Warranty