Manuals / Asante Technologies / Computer Equipment / Network Router

Asante Technologies 1012 manual Snmp Agent, Parameters Menu System

Models: 1012

1 110

Download 110 pages 37.51 Kb

Page 67

Conﬁguration Menu System

SNMP Agent	The bridge SNMP agent menu has the following four submenus:
Parameters
Menu System

Figure 3-7 SNMP Agent Parameters Menu

❏TCP/IP Parameters, deﬁning the bridge IP address, sub- net mask, and default router IP address

❏Software Update, deﬁning the server IP address for a remote boot, the boot protocol to be used, the boot ﬁle name, and the update command itself

❏Access SNMP Trap Receiver Table

❏Access SNMP Community Name Table

❖Note:The SNMP parameters apply to both the hub and bridge modules in the AsantéBridge 1012.The entire unit has just one Ethernet address and one IP address. ❖

1Use the Up/Down arrow keys to move the highlight bar to select the submenu you want and then press return.

This will open the selected menu window.

2If you don’t want to select another menu, enter control-zto return to the Conﬁguration Menu.

Page 3-11

Image 67

Asante Technologies 1012 manual Snmp Agent, Parameters Menu System, Bridge Snmp agent menu has the following four submenus

Contents

AsantéBridge Users’ Guide Trademarks Tell Us What You Think Page Table of Contents AsantéBridge 1012 Local Management Configuring a Redundant LinkSetting Up Out-of-Band Links Connecting a VT100 Terminal Default SettingsList of Figures Figure C-4 Crossover RJ-45 Cable page C-4 Introduction Manual About ThisIntroduction Intended Audience Intended Audience Conventions Used In This ManualTechnical Support Tell Us What You ThinkQuick Start Start Before YouQuick Start Introducing the AsantéBridge Introducing AsantéBridgeBridging Between Two Segments Snmp AsantéBridge FeaturesAsantéBridge Quick ViewFront Panel Quick View Bridge Hub Port Status LEDs RJ45 Port ConnectorsBridge External Port Status LED Bridge Spanning Tree Status LEDsAsantéBridge 1012 Rear Panel RJ21 Port Connector3in1 Port Bridge External Port Collision LED Through/End DIP SwitchBridge External Port AUI Bridge External Port Link/Receive LEDFan PC/Terminal DIP SwitchAC Power Connector On/Off SwitchFlashing Interpreting LEDsPreparing for the Installation Installing AsantéBridge 1012Installing the AsantéBridge Tools Basic Installation ProceduresUnpacking the AsantéBridge Asante´Hub Positioning the AsantéBridgeRack-mounting the AsantéBridge Page Dividing the Network into Segments Connecting Two Segments to the AsantéBridgeAbout Spanning Trees Shown belowUsing the front panel RJ45 ports Connecting Devices to the AsantéBridgeWhat You Need Conﬁguration Options Using the rear panel RJ21 connectorQuick Start Connecting to the Network Before You Start Connecting to the NetworkAbout Bridging About BridgingBridging between segments Simple Transparent BridgeAbout Bridging Like this Spanning TreeRedundant bridging Connecting to the BNC Port Using the 3in1 PortInterconnecting Hubs on Thin Ethernet Backbone Using the 3in1 PortInterconnecting Using Foirl Fiber Optic Inter-Repeater Link Connecting to the AUI PortInterconnecting to Thick Ethernet Backbone Connecting to the RJ45 in and Out Ports Connecting an In-Band Daisychaining Checking the Link Conﬁguring a Redundant Link10BaseT An Example Conﬁguration Conﬁguring a Redundant LinkIf a Link Goes Down to the Main Hub If the Main Hub Goes DownSetting Up Out-of-Band Links Setting Up Out-of-Band LinksInterconnecting Hubs 10 Connecting the Asanté Management Station for Out-of-Band Distance Restrictions Recommended MethodPC/Terminal Switch Conﬁguring Hub DIP SwitchesThrough/End Switch Connecting a VT100 Terminal Connecting a VT100 TerminalLists the factory default settings Default SettingsAsantéBridge 1012 Local Management AsantéBridge 1012 Local Management These functions, use the following ﬂow chartBridge Diagnostics Bridge DiagnosticsLocal Management Main Menu Local ManagementLocal Management Menu System Local Management Help Window General Help MenuConﬁguration Menu System Accessing the Conﬁguration Menu systemConﬁguration Menu System Reset System item is a command. Selecting this item Information Menu SystemPassword Menu Password MenuParameters Menu System Snmp AgentBridge Snmp agent menu has the following four submenus TCP/IP Parameters Menu TCP/IP Parameters MenuSoftware Update Menu Software Update MenuAbout the Software Update function Conﬁguration Menu System Menu without taking any action 10 System Update Status WindowConﬁguration Menu System 11 Snmp Trap Receiver Table Snmp Trap Receiver Table12 Snmp Community Name Table Snmp Community Name TableThis table allows you to control access to Snmp MIB objects 13 Out-of-Band Parameters Menu Out-of-Band Parameters MenuEnter control-z to return to the Conﬁguration Menu 14 Bridge Parameters Menu Bridge Parameters Menu System15 Spanning Tree Bridge Parameters Menu Spanning Tree Bridge Parameters MenuActivity.To update the window, enter control-r 16 Spanning Tree Port Setting Menu Spanning Tree Port Setting MenuAbout Forwarding Bridge Forwarding TableExit returns you to the Bridge Parameters Menu About dynamic and static table entries Alphabetic portion of the ﬁeld deﬁnes the type of entryAsantéBridge 1012 Local Management 18 Editing the Forwarding Table Using the Edit Function19 Searching for an Address Using the Search FunctionAbout the Filtering Table Bridge Filtering Table20 Bridge Filtering Table Conﬁguration Menu System 21 Resetting the Bridge Resetting the BridgeMenu 22 Bridge Statistics Statistics Menu SystemSupport for Pre 10BaseT Devices Appendix a Support for Pre 10BaseT Devices Technical Speciﬁcations Appendix B Technical Speciﬁcations B-3 B-4 Pinouts and Cable Speciﬁcations RJ-45 to RJ-21 Pinouts Amphenol to Modular Jack Appendix C Pinouts and Cable SpeciﬁcationsC-3 RJ-45 to RJ-45 Crossover Cable RJ-45 Modular Jack to Wall Jack PinoutsTable C-1 AUI Pinouts AUI DB-15 PinoutsC-6 AsantéBridge 1012 Index LED Numerics Manual P/N