B-3 | Asante Technologies 1012 guide

1 to show Uplink Link/Receive Status (rear panel)

3 to show received packets, forwarded packets, collisions on external bridge port

3 to show received packets, forwarded packets, collisions on hub bridge port

3 to show bridge status within a spanning tree

Power Requirements:

Input Voltage: 100-250 VAC, 47-63 Hz single phase; continuous voltage input range

Input Current: 1.2A @ 100 VAC (Max.)

0.5A @ 220 VAC (Maximum)

0.5A @ 100 VAC (typical)

Electromagnetic Emissions: Meets FCC Class A requirements

Safety: Designed in accordance with UL 1950, CSA 22.2 No. 220, IEC 950,TUV, and VDE requirements

Mounting: Desktop, Rack (with bracket), or Wall (with bracket)

Physical Dimensions: 10” L (25.4 cm) x 2.2” H (5.9 cm) x 16” W (40.6 cm)

Weight:Approximately 6 lbs. (2.73 kg)

Environmental:

Operating Temperature: 0 to 40° C ambient

Operating Humidity: 5 to 85% noncondensing

Operating Altitude: 10,000 ft. (3,048 m)

Storage Temperature: -30 to 80° C

Storage Humidity: 5 to 90% noncondensing

Storage Altitude: 25,000 ft. (7,620 m)

Page B-3

Image 99

Asante Technologies 1012 manual B-3

Contents

AsantéBridge Users’ Guide Trademarks Tell Us What You Think Page Table of Contents AsantéBridge 1012 Local Management Configuring a Redundant LinkSetting Up Out-of-Band Links Connecting a VT100 Terminal Default Settings List of Figures Figure C-4 Crossover RJ-45 Cable page C-4 Introduction About This ManualIntroduction Intended Audience Intended Audience Conventions Used In This Manual Technical Support Tell Us What You Think Quick Start Before You StartQuick Start Introducing the AsantéBridge Introducing AsantéBridge Bridging Between Two Segments Snmp AsantéBridge Features Quick View AsantéBridgeFront Panel Quick View Bridge Hub Port Status LEDs RJ45 Port ConnectorsBridge External Port Status LED Bridge Spanning Tree Status LEDs RJ21 Port Connector AsantéBridge 1012 Rear Panel3in1 Port Bridge External Port Collision LED Through/End DIP SwitchBridge External Port AUI Bridge External Port Link/Receive LED Fan PC/Terminal DIP SwitchAC Power Connector On/Off Switch Flashing Interpreting LEDs Installing AsantéBridge 1012 Preparing for the InstallationInstalling the AsantéBridge Basic Installation Procedures ToolsUnpacking the AsantéBridge Asante´Hub Positioning the AsantéBridge Rack-mounting the AsantéBridge Page Dividing the Network into Segments Connecting Two Segments to the AsantéBridge About Spanning Trees Shown below Connecting Devices to the AsantéBridge Using the front panel RJ45 portsWhat You Need Conﬁguration Options Using the rear panel RJ21 connector Quick Start Connecting to the Network Before You Start Connecting to the Network About Bridging About Bridging Bridging between segments Simple Transparent Bridge About Bridging Like this Spanning Tree Redundant bridging Connecting to the BNC Port Using the 3in1 Port Interconnecting Hubs on Thin Ethernet Backbone Using the 3in1 Port Interconnecting Using Foirl Fiber Optic Inter-Repeater Link Connecting to the AUI Port Interconnecting to Thick Ethernet Backbone Connecting to the RJ45 in and Out Ports Connecting an In-Band Daisychaining Conﬁguring a Redundant Link Checking the Link10BaseT An Example Conﬁguration Conﬁguring a Redundant Link If a Link Goes Down to the Main Hub If the Main Hub Goes Down Setting Up Out-of-Band Links Setting Up Out-of-Band LinksInterconnecting Hubs 10 Connecting the Asanté Management Station for Out-of-Band Distance Restrictions Recommended Method Conﬁguring Hub DIP Switches PC/Terminal SwitchThrough/End Switch Connecting a VT100 Terminal Connecting a VT100 Terminal Lists the factory default settings Default Settings AsantéBridge 1012 Local Management AsantéBridge 1012 Local Management These functions, use the following ﬂow chart Bridge Diagnostics Bridge Diagnostics Local Management Main Menu Local Management Local Management Menu System Local Management Help Window General Help Menu Accessing the Conﬁguration Menu system Conﬁguration Menu SystemConﬁguration Menu System Reset System item is a command. Selecting this item Information Menu System Password Menu Password Menu Snmp Agent Parameters Menu SystemBridge Snmp agent menu has the following four submenus TCP/IP Parameters Menu TCP/IP Parameters Menu Software Update Menu Software Update Menu About the Software Update function Conﬁguration Menu System Menu without taking any action 10 System Update Status Window Conﬁguration Menu System 11 Snmp Trap Receiver Table Snmp Trap Receiver Table 12 Snmp Community Name Table Snmp Community Name Table This table allows you to control access to Snmp MIB objects 13 Out-of-Band Parameters Menu Out-of-Band Parameters Menu Enter control-z to return to the Conﬁguration Menu 14 Bridge Parameters Menu Bridge Parameters Menu System 15 Spanning Tree Bridge Parameters Menu Spanning Tree Bridge Parameters Menu Activity.To update the window, enter control-r 16 Spanning Tree Port Setting Menu Spanning Tree Port Setting Menu About Forwarding Bridge Forwarding Table Exit returns you to the Bridge Parameters Menu About dynamic and static table entries Alphabetic portion of the ﬁeld deﬁnes the type of entry AsantéBridge 1012 Local Management 18 Editing the Forwarding Table Using the Edit Function 19 Searching for an Address Using the Search Function About the Filtering Table Bridge Filtering Table 20 Bridge Filtering Table Conﬁguration Menu System 21 Resetting the Bridge Resetting the Bridge Menu 22 Bridge Statistics Statistics Menu System Support for Pre 10BaseT Devices Appendix a Support for Pre 10BaseT Devices Technical Speciﬁcations Appendix B Technical Speciﬁcations B-3 B-4 Pinouts and Cable Speciﬁcations RJ-45 to RJ-21 Pinouts Amphenol to Modular Jack Appendix C Pinouts and Cable Speciﬁcations C-3 RJ-45 to RJ-45 Crossover Cable RJ-45 Modular Jack to Wall Jack Pinouts Table C-1 AUI Pinouts AUI DB-15 Pinouts C-6 AsantéBridge 1012 Index LED Numerics Manual P/N