Manuals / Asante Technologies / Computer Equipment / Network Router

Asante Technologies 1012 manual PC/Terminal DIP Switch, Fan, AC Power Connector, AC Line Fuse

Models: 1012

1 110

Download 110 pages 37.51 Kb

Page 23

Quick View

Set the switch on all other hubs in the daisychain to the UP position.

Only one hub at the end of the daisychain can have this switch down. All others hubs in the chain must have it up.

PC/Terminal DIP Switch

This switch controls the conﬁguration for the Bridge/Hub RS232 port and the AMS out-of-band link ports. How you set the switch depends on how you connect your Macintosh or PC run- ning AsantéView Out-of-Band.

If you are running AsantéView Out-of-Band and your Asanté Management Station is connected to the Bridge/Hub RS232 port, set this switch UP.The PC/Terminal switches on all other hubs in the out-of-band daisychain must be set DOWN.

If you want to use the Bridge/Hub RS232 port for local manage- ment, set this switch DOWN.

If you are running AsantéView Out-of-Band and your Asanté Management Station is connected to the AMS Link port, set this switch DOWN on all hubs on the out-of-band daisychain.

Fan

This is a small cooling fan for the AsantéBridge 1012.The fan should turn on when the unit is powered on. Do not operate the hub if the fan does not come on.

AC Power Connector

Plug the AC power cord into this connector.

AC Line Fuse

The AC fuse for the unit is behind this cover plate.You must remove the plate to access and replace the fuse.

Included in each hub is a spare fuse.To access the spare fuse, pry out the fuse holder with a ﬂathead screwdriver.With some units, this can take extra effort.The fuse holder slides straight out from the back of the Hub.The spare fuse is in a small black box inside the fuse holder.To open, push out from one end.

On/Off Switch

Turns the AsantéBridge 1012 on and off.

Page 1-11

Image 23

Asante Technologies 1012 manual PC/Terminal DIP Switch, Fan, AC Power Connector, AC Line Fuse, On/Off Switch

Contents

AsantéBridge Users’ Guide Trademarks Tell Us What You Think Page Table of Contents AsantéBridge 1012 Local Management Configuring a Redundant LinkSetting Up Out-of-Band Links Connecting a VT100 Terminal Default SettingsList of Figures Figure C-4 Crossover RJ-45 Cable page C-4 Introduction Introduction About ThisManual Intended Audience Intended Audience Conventions Used In This ManualTechnical Support Tell Us What You ThinkQuick Start Quick Start Before YouStart Introducing the AsantéBridge Introducing AsantéBridgeBridging Between Two Segments Snmp AsantéBridge FeaturesFront Panel Quick ViewAsantéBridge Quick View Bridge Hub Port Status LEDs RJ45 Port ConnectorsBridge External Port Status LED Bridge Spanning Tree Status LEDs3in1 Port RJ21 Port ConnectorAsantéBridge 1012 Rear Panel Bridge External Port Collision LED Through/End DIP SwitchBridge External Port AUI Bridge External Port Link/Receive LEDFan PC/Terminal DIP SwitchAC Power Connector On/Off SwitchFlashing Interpreting LEDsInstalling the AsantéBridge Installing AsantéBridge 1012Preparing for the Installation Unpacking the AsantéBridge Basic Installation ProceduresTools Asante´Hub Positioning the AsantéBridgeRack-mounting the AsantéBridge Page Dividing the Network into Segments Connecting Two Segments to the AsantéBridgeAbout Spanning Trees Shown belowWhat You Need Connecting Devices to the AsantéBridgeUsing the front panel RJ45 ports Conﬁguration Options Using the rear panel RJ21 connectorQuick Start Connecting to the Network Before You Start Connecting to the NetworkAbout Bridging About BridgingBridging between segments Simple Transparent BridgeAbout Bridging Like this Spanning TreeRedundant bridging Connecting to the BNC Port Using the 3in1 PortInterconnecting Hubs on Thin Ethernet Backbone Using the 3in1 PortInterconnecting Using Foirl Fiber Optic Inter-Repeater Link Connecting to the AUI PortInterconnecting to Thick Ethernet Backbone Connecting to the RJ45 in and Out Ports Connecting an In-Band Daisychaining 10BaseT Conﬁguring a Redundant LinkChecking the Link An Example Conﬁguration Conﬁguring a Redundant LinkIf a Link Goes Down to the Main Hub If the Main Hub Goes DownInterconnecting Hubs Setting Up Out-of-Band LinksSetting Up Out-of-Band Links 10 Connecting the Asanté Management Station for Out-of-Band Distance Restrictions Recommended MethodThrough/End Switch Conﬁguring Hub DIP SwitchesPC/Terminal Switch Connecting a VT100 Terminal Connecting a VT100 TerminalLists the factory default settings Default SettingsAsantéBridge 1012 Local Management AsantéBridge 1012 Local Management These functions, use the following ﬂow chartBridge Diagnostics Bridge DiagnosticsLocal Management Main Menu Local ManagementLocal Management Menu System Local Management Help Window General Help MenuConﬁguration Menu System Accessing the Conﬁguration Menu systemConﬁguration Menu System Reset System item is a command. Selecting this item Information Menu SystemPassword Menu Password MenuBridge Snmp agent menu has the following four submenus Snmp AgentParameters Menu System TCP/IP Parameters Menu TCP/IP Parameters MenuSoftware Update Menu Software Update MenuAbout the Software Update function Conﬁguration Menu System Menu without taking any action 10 System Update Status WindowConﬁguration Menu System 11 Snmp Trap Receiver Table Snmp Trap Receiver Table12 Snmp Community Name Table Snmp Community Name TableThis table allows you to control access to Snmp MIB objects 13 Out-of-Band Parameters Menu Out-of-Band Parameters MenuEnter control-z to return to the Conﬁguration Menu 14 Bridge Parameters Menu Bridge Parameters Menu System15 Spanning Tree Bridge Parameters Menu Spanning Tree Bridge Parameters MenuActivity.To update the window, enter control-r 16 Spanning Tree Port Setting Menu Spanning Tree Port Setting MenuAbout Forwarding Bridge Forwarding TableExit returns you to the Bridge Parameters Menu About dynamic and static table entries Alphabetic portion of the ﬁeld deﬁnes the type of entryAsantéBridge 1012 Local Management 18 Editing the Forwarding Table Using the Edit Function19 Searching for an Address Using the Search FunctionAbout the Filtering Table Bridge Filtering Table20 Bridge Filtering Table Conﬁguration Menu System 21 Resetting the Bridge Resetting the BridgeMenu 22 Bridge Statistics Statistics Menu SystemSupport for Pre 10BaseT Devices Appendix a Support for Pre 10BaseT Devices Technical Speciﬁcations Appendix B Technical Speciﬁcations B-3 B-4 Pinouts and Cable Speciﬁcations RJ-45 to RJ-21 Pinouts Amphenol to Modular Jack Appendix C Pinouts and Cable SpeciﬁcationsC-3 RJ-45 to RJ-45 Crossover Cable RJ-45 Modular Jack to Wall Jack PinoutsTable C-1 AUI Pinouts AUI DB-15 PinoutsC-6 AsantéBridge 1012 Index LED Numerics Manual P/N