Remote Port Security Device User’s Manual
AT&T
DEFINITY System
Communications
1991 AT&T All Rights Reserved Printed in USA
TRADEMARK NOTICE
ORDERING INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
120 V AC +/- 10% 6Hz
SAVE THESE INSTRUCTIONS
Input rating
150 mA maximum
FCC Notices
Part 15, Subpart A
Part
Contents
2 Installation
Getting Started
3 RPSD System Administration
RPSD Key Use
5 Troubleshooting
Cables, Connectors, and Ports Table
Device LEDs
List of Figures
Page
4-1Access Failure Messages 5-1Access Failure Messages
List of Tables
2-2Cables, Connectors, and Ports 3-1Access Failure Messages
A-1Cables, Connectors, and Ports B-1RPSD Lock LEDs B-2RPSD Key LEDs
1 Getting Started
Getting Started
Getting Started
The entire sequence occurs in less than 20 seconds
RPSD Lock and Key Configuration
Audience
Responsibilities
In This Document
Typographical Conventions
Block user RETURN
Hotline or Other Service Call Numbers/Addresses
1-6 Getting Started
2 Installation
Installation
Installation
2-2 Installation
Power Supply
Room Layout/Environment
Location of Administration Terminal or Printer
Hardware Components
RPSD Lock
RPSD Power Monitor Adapter
2-6 Installation
ModemTelco Typical Wiring Scheme Bypass Wiring Scheme
Bypass Connections
PBXs
Other
RPSD Lock or Key Administration Terminal
RPSD Lock Administration Printer
Modems
RPSD Key
RPSD Key
Hardware Installation Procedures
Installing the RPSD Lock
on the circuit pack for System 75 and DEFINITY Generic
Connecting the RPSD Lock to the CO Line
Connecting the RPSD Lock to the PBX Modem
Connecting the RPSD Lock to the Administration Terminal or Printer
RPSD Lock to Modem
RPSD
Signal
Aux. Port, Terminal, and Printer Pinouts
To DTE
RPSD Lock to Administratlon Terminal or Printer
Hardware Installation Procedures
2-17
DB25 Connections From RPSD Lock or Key to Data Terminal Equipment
Powering Up the RPSD Lock
Installing the RPSD Key
Powering Up the RPSD Key
Connecting the RPSD Key to the Terminal
Connecting the RPSD Key to the Modem
Power-Up Behavior of Initialized Key
Testing an Uninitialized Key
Power-Up Behavior of Uninitialized Key
Part
Cables, Connectors, and Ports Table
Cables, Connectors, and Ports
From
2-24 Installation
Aux. Port Settings
Software Components
Initializing the RPSD Lock
Initializing an RPSD Key
2-26 Installation
Test RPSD Lock Installation
Test RPSD Lock Installation
3 RPSD System Administration
RPSD System Administration
Time of Day Access
System Activity Log
Log ID
Force Connect/Disconnect
Single Point Administration
Enable/Disable Block AT&T and Other Key Users
3-4 RPSD System Administration
Authorized Keys
3-6 RPSD System Administration
RPSD System Administrator Command Set
A - Add User
Sample Command and Response Without Optional Secret Key
Sample Command and Response With Optional Secret Key
3-8 RPSD System Administration
b userid RETURN
B - Block User
U - Unblock User
u userid RETURN
T - Test User
R - Remove User
L - List User Table
Blocked?
Second Sample Command and Response
User ID
Permanent?
The fields of this screen are explained in the first sample, above
Third Sample Command and Response
RPSD System Administrator Command Set
3-13
CR - Change Restriction
starthhmm endhhmm dayno
LR - List Restrictions
lr restrid RETURN
ur fullorpartialuserid, restrids, clear
UR - User Restrictions
ur fullorpartialuserid, restrids RETURN
3-17
LH - Log History
The fields of the Log History screen are
AH - Access History
FH - Failure History
ST - Status Display
LS - List Statistics
RS - Reset Statistics
FC - Force Connect
d mm/dd/yy RETURN
FD - Force Disconnect
D - Date Set
3-25
C - Clock Set
I - ID Set
SC - Set Communications Parameters
Help Screens
3-28 RPSD System Administration
Sample Help Request and Help Response
4 RPSD Key Use
RPSD Key Use
Access Failure Messages
Last Call Status Test
4-2 RPSD Key Use
RPSD Key User Command Set
RPSD Key User Command Set
U - Set User ID
K - Set Secret Key
4-4 RPSD Key Use
N - Set Device Number
L - List User Information
n number RETURN
H - History Display
d 08/14/90 08/14/90 131413 Date Changed OK
D - Date Set
C - Clock Set
c 8/14/90 131500 Time Changed OK
I - Set Log ID
4-8 RPSD Key Use
S - Status Display
s RETURN
SC - Set Communications Parameters
4-10 RPSD Key Use
sc 1200,7E 08/14/90 134821 Comms Params Changed to 1200/7E
W - Wipe Out
The RPSD Key requests confirmation of the Wipe Out command
Help Screens
5 Troubleshooting
Troubleshooting
Troubleshooting
5-2 Troubleshooting
Access Failure Messages
Access Failure Messages
described in Testing the RPSD Lock in this
Check described in Testing the RPSD Lock
Check described in Testing the RPSD Lock
5-4 Troubleshooting
Page
5-6 Troubleshooting
Testing the RPSD Lock
Built-in Diagnostics
Self Check
Last Call Status Test
5-8 Troubleshooting
Hardware Replacement
Modem Ring Test
Replacing the PBX Modem
5-10 Troubleshooting
Replacing the Lock or Key
Replacing the Lock or Key
5-12 Troubleshooting
Saving the Key Seed Value
Saving the Key Seed Value
A Cables, Connectors, and Ports Table
Cables, Connectors, and Ports Table
B Device LEDs
Front Panel LEDs
RPSD Lock
FIGURE B-1 RPSD Lock LEDs
AT&T
DEFINITY RPSD
RPSD Key
Page
Index
I-2 Index