AT&T
DEFINITY System
Remote Port Security Device User’s Manual
Communications
ORDERING INFORMATION
1991 AT&T All Rights Reserved Printed in USA
TRADEMARK NOTICE
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Input rating
120 V AC +/- 10% 6Hz
150 mA maximum
Part
FCC Notices
Part 15, Subpart A
Getting Started
Contents
2 Installation
3 RPSD System Administration
5 Troubleshooting
Cables, Connectors, and Ports Table
RPSD Key Use
Device LEDs
List of Figures
Page
List of Tables
2-2Cables, Connectors, and Ports 3-1Access Failure Messages
4-1Access Failure Messages 5-1Access Failure Messages
A-1Cables, Connectors, and Ports B-1RPSD Lock LEDs B-2RPSD Key LEDs
1 Getting Started
Getting Started
Getting Started
The entire sequence occurs in less than 20 seconds
RPSD Lock and Key Configuration
Audience
Responsibilities
Block user RETURN
In This Document
Typographical Conventions
Hotline or Other Service Call Numbers/Addresses
1-6 Getting Started
2 Installation
Installation
Installation
2-2 Installation
Power Supply
Room Layout/Environment
Location of Administration Terminal or Printer
Hardware Components
RPSD Lock
RPSD Power Monitor Adapter
2-6 Installation
ModemTelco Typical Wiring Scheme Bypass Wiring Scheme
Bypass Connections
PBXs
RPSD Lock or Key Administration Terminal
RPSD Lock Administration Printer
Other
Modems
RPSD Key
RPSD Key
Hardware Installation Procedures
Installing the RPSD Lock
on the circuit pack for System 75 and DEFINITY Generic
Connecting the RPSD Lock to the CO Line
Connecting the RPSD Lock to the PBX Modem
Connecting the RPSD Lock to the Administration Terminal or Printer
RPSD Lock to Modem
Signal
Aux. Port, Terminal, and Printer Pinouts
RPSD
To DTE
2-17
RPSD Lock to Administratlon Terminal or Printer
Hardware Installation Procedures
DB25 Connections From RPSD Lock or Key to Data Terminal Equipment
Powering Up the RPSD Lock
Installing the RPSD Key
Connecting the RPSD Key to the Terminal
Connecting the RPSD Key to the Modem
Powering Up the RPSD Key
Power-Up Behavior of Initialized Key
Testing an Uninitialized Key
Power-Up Behavior of Uninitialized Key
Cables, Connectors, and Ports Table
Cables, Connectors, and Ports
Part
From
2-24 Installation
Initializing the RPSD Lock
Aux. Port Settings
Software Components
Initializing an RPSD Key
2-26 Installation
Test RPSD Lock Installation
Test RPSD Lock Installation
3 RPSD System Administration
RPSD System Administration
Time of Day Access
System Activity Log
Log ID
Single Point Administration
Enable/Disable Block AT&T and Other Key Users
Force Connect/Disconnect
3-4 RPSD System Administration
Authorized Keys
3-6 RPSD System Administration
RPSD System Administrator Command Set
A - Add User
3-8 RPSD System Administration
Sample Command and Response Without Optional Secret Key
Sample Command and Response With Optional Secret Key
B - Block User
U - Unblock User
b userid RETURN
u userid RETURN
T - Test User
R - Remove User
L - List User Table
Second Sample Command and Response
User ID
Blocked?
Permanent?
Third Sample Command and Response
RPSD System Administrator Command Set
The fields of this screen are explained in the first sample, above
3-13
CR - Change Restriction
starthhmm endhhmm dayno
LR - List Restrictions
lr restrid RETURN
UR - User Restrictions
ur fullorpartialuserid, restrids RETURN
ur fullorpartialuserid, restrids, clear
3-17
LH - Log History
The fields of the Log History screen are
AH - Access History
FH - Failure History
ST - Status Display
LS - List Statistics
RS - Reset Statistics
FC - Force Connect
FD - Force Disconnect
D - Date Set
d mm/dd/yy RETURN
3-25
C - Clock Set
I - ID Set
SC - Set Communications Parameters
Sample Help Request and Help Response
Help Screens
3-28 RPSD System Administration
4 RPSD Key Use
RPSD Key Use
4-2 RPSD Key Use
Access Failure Messages
Last Call Status Test
RPSD Key User Command Set
RPSD Key User Command Set
4-4 RPSD Key Use
U - Set User ID
K - Set Secret Key
n number RETURN
N - Set Device Number
L - List User Information
H - History Display
D - Date Set
C - Clock Set
d 08/14/90 08/14/90 131413 Date Changed OK
c 8/14/90 131500 Time Changed OK
I - Set Log ID
4-8 RPSD Key Use
S - Status Display
s RETURN
sc 1200,7E 08/14/90 134821 Comms Params Changed to 1200/7E
SC - Set Communications Parameters
4-10 RPSD Key Use
Help Screens
W - Wipe Out
The RPSD Key requests confirmation of the Wipe Out command
5 Troubleshooting
Troubleshooting
Troubleshooting
5-2 Troubleshooting
Access Failure Messages
Access Failure Messages
Check described in Testing the RPSD Lock
Check described in Testing the RPSD Lock
described in Testing the RPSD Lock in this
5-4 Troubleshooting
Page
5-6 Troubleshooting
Testing the RPSD Lock
Built-in Diagnostics
5-8 Troubleshooting
Self Check
Last Call Status Test
Hardware Replacement
Modem Ring Test
Replacing the PBX Modem
5-10 Troubleshooting
Replacing the Lock or Key
Replacing the Lock or Key
5-12 Troubleshooting
Saving the Key Seed Value
Saving the Key Seed Value
A Cables, Connectors, and Ports Table
Cables, Connectors, and Ports Table
B Device LEDs
FIGURE B-1 RPSD Lock LEDs
Front Panel LEDs
RPSD Lock
RPSD Key
AT&T
DEFINITY RPSD
Page
Index
I-2 Index