Conair GB/ WSB manual Specifications, Appendix B

TPS014/1199

SPECIFICATIONS

GRAVIMETRIC BATCH BLENDERS AutoWeigh GB1840 and 1860 Models

FEEDER LOCATIONS

DC

4

C 2 1

3

AB

B

TOP VIEW GB1840

CONTROL

D

B

C

A

C

FEEDER LOCATIONS			C
D		C
8	7	4
1	2	3
A	B	B

TOP VIEW GB1860

NOTE: Any one of the feeders (A,B,C or D) can be designated position 5 or 6.

E

F

FRONT VIEW	SIDE VIEW	SIDE VIEW
GB1840/GB1860	GB1840	GB1860

MODELS				GB1840	GB1860
Performance characteristics
Batch size lbs {g}				39.7 {18000}	39.7 {18000}
Maximum throughput lbs/hr {kg/hr}*				4114 {1870}	2566 {1166}
Bin Capacity - Main Ingredient		ft3 {liter}		6.7 {189.7}	3.8 {107.6}
Bin Capacity - Minor Capacity		ft3 {liter}		3.8 {107.6}	3.8 {107.6}
Maximum number of materials				8	10
Number of discharge valves				4	6
Number of additive feeders				up to 4	up to 4
Control software (# of components)				4 or 12	12
Dimensions inches {mm}
A - Height above mounting plate				93 {2362.2}	93 {2362.2}
B - Width†				56 {1421.4}	56 {1421.4}
C - Depth†				34 {863.6}	34 {863.6}
D - Controller height				11.25 {285.75}	11.25 {285.75}
E - Controller width				12.25 {311.15}	12.25 {311.15}
F - Controller depth				8.19 {208.03}	8.19 {208.03}
Weight lbs {kg}
Installed				730 {331}	730 {331}
Shipping				850 {385.5}	850 {385.5}
Voltage Running load amps‡
110V/1 phase/60hz	(control)			0.3	0.3
220V/1 phase/60hz	(mixer)			8.2	8.2
220V/1 phase/60hz	(control)			0.2	0.2
220V/1 phase/60hz	(mixer)			8.2	8.2
220V/1 phase/50hz	(control)			0.2	0.2
220V/3 phase/50hz	(mixer)			4.4	4.4
400V/3 phase/50hz	(mixer)			2.2	2.2
Compressed air requirements
Discharge valves			80 psi @ 0.2 ft3/min {5.5 bars @ 0.09 liters/sec}
				1/4 in. NPT fitting
Maximum loader sizes §
Number of 20 inch loaders				2	3
Number of 15 inch loaders				4	6

MOUNTING INTERFACE

	(4) 9/16 in. {14.3 mm}
IB04
	diameter bolt holes

4 in. {101.6 mm}	8 in. {203.2 mm}
diameter	square bolt pattern
through hole
14.5 in.	16 in.
	{406.4 mm}
{368.3 mm}
15 in. {381 mm}
20 in. {508 mm}

SPECIFICATION NOTES

*Maximum throughput rates are based on 35 lb/ft3 pel- letized material and using all dispense valves. Use of feeders for minor ingredients will reduce this rate.

Refer to the selection guide for more specific through- put information.

†Feeders will increase width dimensions. Please refer to feeder specification.

‡Each auger feeder requires an additional 1 amp @ 120V or 0.5 amp @ 240V.

§Maximum loader sizes may be used only when the loader is adjacent to loaders of a smaller diameter.

One Conair Drive ● Pittsburgh, PA 15202 ● 412-312-6000 ● FAX 412-312-6227 ● www.conairnet.com

APPENDIX B