SPECIFICATIONS
TPBS004/1199
GRAVIMETRIC BATCH BLENDERS
WSB 920, 940, 950 and 960 Models
NOTE: Loader configuration is the same for all models.
CONTROL
MODELS |
| WSB920 | WSB940 | WSB950 | WSB960 |
Performance characteristics |
|
|
|
|
|
Batch size lbs {g} |
| 19.8 {9000} | 19.8 {9000} | 19.8 {9000} | 19.8 {9000} |
Maximum throughput lbs/hr {kg/hr}* | 5200 {2359} | 3300 {1487} | 2492 {1132} | 2124 {965} | |
Bin capacity - main ingredient | ft3 {liter} | 6.7 {189.7} | 6.7 {189.7} | 6.7 {189.7} | NA |
Bin capacity - minor ingredient | ft3 {liter} | NA | 3.8 {107.6} | 3.8 {107.6} | 3.8 {107.6} |
Maximum number of materials |
| 6 | 8 | 9 | 10 |
Number of discharge valves |
| 2 | 4 | 5 | 6 |
Number of additive feeders |
| up to 4 | up to 4 | up to 4 | up to 4 |
Control software (# of components) | 4 or 12 | 4 or 12 | 12 | 12 | |
Dimensions inches {mm} |
|
|
|
|
|
A - Height above mounting plate | 74 {1880.7} | 74 {1880.7} | 74 {1880.7} | 74 {1880.7} | |
B - Width† |
| 56 {1421.4} | 56 {1421.4} | 56 {1421.4} | 56 {1421.4} |
C - Depth† |
| 34.4 {875.3} | 34.4 {875.3} | 34.4 {875.3} | 34.4 {875.3} |
D - Controller height |
| 11.25 {285.75} | 11.25 {285.75} | 11.25 {285.75} | 11.25 {285.75} |
E - Controller width |
| 12.25 {311.15} | 12.25 {311.15} | 12.25 {311.15} | 12.25 {311.15} |
F - Controller depth |
| 8.19 {208.03} | 8.19 {208.03} | 8.19 {208.03} | 8.19 {208.03} |
Weight lbs {kg} |
|
|
|
|
|
Installed |
| 480 {218} | 480 {218} | 480 {218} | 480 {218} |
Shipping |
| 600 {272.2} | 600 {272.2} | 600 {272.2} | 600 {272.2} |
Voltage Running load amps ‡ |
|
|
|
|
|
120V/1 phase/60 hz (control and mixer) | 8.5 | 8.5 | 8.5 | 8.5 | |
220V/1 phase/60 hz (control and mixer) | 4.3 | 4.3 | 4.3 | 4.3 | |
220V/1 phase/50 hz (control) |
| 0.15 | 0.15 | 0.15 | 0.15 |
220V/3 phase/50 hz (mixer) |
| 2.2 | 2.2 | 2.2 | 2.2 |
400V/3 phase/50 hz (mixer) |
| 1.1 | 1.1 | 1.1 | 1.1 |
Compressed air requirements |
|
|
|
|
|
Discharge valves |
| 80 psi @ 0.2 ft3/min {5.5 bars @ 0.09 liters/sec}; 1/4 in. NPT fitting | |||
Compressed air feeder |
| 40 psi @ 2.0 ft3/min {2.8 bars @ 0.94 liters/sec}; 1/4 in. NPT fitting | |||
Maximum loader sizes§ |
|
|
|
|
|
Number of 20 inch loaders |
| 2 | 2 | 2 | 3 |
Number of 15 inch loaders |
| 2 | 4 | 5 | 6 |
|
|
|
|
|
|
MOUNTING INTERFACE
IB04
SPECIFICATION NOTES:
*Maximum throughput rates are based on using all dispense valves. Use of feeders for minor ingredients will reduce this rate.
†Feeders will increase width and depth dimensions. Please refer to feeder specification.
‡Each auger feeder requires an additional 1 amp @ 120V or 0.5 amp @ 240V.
§Maximum loader sizes may be used only when the loader is adjacent to loaders of a smaller size.
APPLICATION NOTE:
We recommend using a flow con- trol valve when mounting the blender to a stand, surge bin or hopper.
One Conair Drive ● Pittsburgh, PA 15202 ●
APPENDIX B
