Conair GB/ WSB manual Specifications, Appendix B

SPECIFICATIONS

TPBS012/1199

GRAVIMETRIC BATCH BLENDERS AutoWeigh GB240 and GB440 Models

TOP VIEW

	B
4	3
C
A	B
1	2

MOUNTING	14 in.
INTERFACE
IB04	{355.6 mm}
8 in. {203.2 mm}	10 in.
square bolt pattern	{254 mm
(4) 9/16 in.	3 in. {76.2 mm}
{14.3 mm}	diameter
diameter	through hole
bolt holes

	C
B

A

FRONT VIEW SIDE VIEW CONTROL

MODELS		GB240	GB241	GB242	GB440	GB441	GB442
Performance characteristics
Batch size lbs {g}		4.4 {2000}	4.4 {2000}	4.4 {2000}	8.8 {4000}	8.8 {4000}	8.8 {4000}
Maximum throughput lbs/hr {kg/hr}*		993 {451}	678 {308}	518 {235}	1645 {748}	983 {446}	704 {319}
Bin capacity - main ingredient	ft3 {liter}	3.5 {99.12}	3.5 {99.12}	3.5 {99.12}	3.5 {99.12}	3.5 {99.12}	3.5 {99.12}
Bin capacity - minor ingredient	ft3 {liter}	NA	0.5 {14.16}	0.5 {14.16}	NA	0.5 {14.16}	0.5 {14.16}
Maximum number of materials		4	5	6	4	5	6
Number of discharge valves		4	4	4	4	4	4
Number of additive feeders		0	1	2	0	1	2
Control software (# of components)		4 or 12	12	12	4 or 12	12	12
Dimensions inches {mm}
A - Height above mounting plate†		59.75 {1517.5}	59.75 {1517.5}	59.75 {1517.5}	65.75 {1669.9}	65.75 {1669.9}	65.75 {1669.9}
B - Width ‡		34 {863.6}	34 {863.6}	34 {863.6}	34 {863.6}	34 {863.6}	34 {863.6}
C - Depth‡		34 {863.6}	34 {863.6}	34 {863.6}	34 {863.6}	34 {863.6}	34 {863.6}
D - Controller height		11.25 {285.75}	11.25 {285.75}	11.25 {285.75}	11.25 {285.75}	11.25 {285.75}	11.25 {285.75}
E - Controller width		12.25 {311.15}	12.25 {311.15}	12.25 {311.15}	12.25 {311.15}	12.25 {311.15}	12.25 {311.15}
F - Controller depth		8.19 {208.03}	8.19 {208.03}	8.19 {208.03}	8.19 {208.03}	8.19 {208.03}	8.19 {208.03}
Weight lbs {kg}
Installed		230 {104}	270 {122}	310 {140}	255 {116}	295 {134}	335 {152}
Shipping		335 {152}	375 {170}	415 {188}	360 {163}	400 {181}	440{200}
Voltage Total amps
120V/1 phase/50-60 Hz		4.8	5.8	6.8	4.8	5.8	6.8
240V/1 phase/50-60 Hz		2.5	3.0	3.5	2.5	3.0	3.5
Compressed air requirements
Discharge valves		80 psi @ 0.2 ft3/min. {5.5bars @ 0.09 liters/sec}, 1/4 in. NPT fitting
Compressed air feeder		40 psi @ 2 ft3/min. {2.8bars @ 0.94 liters/sec}, 1/4 in. NPT fitting

SPECIFICATION NOTES:

Each bin compartment can support a 12-inch to 15-inch loader or vacuum receiver.

*Throughput rates are based on using no more than 2% additive or colorant material total in either the CAF3 compressed air or F03 auger feeder. Always refer to the selection guide for specific throughput information.

†The optional flow control valve adds 6.5 in. {165 mm} to the total height. We recommend using the flow control valve when mounting the blender to a stand, surge bin or hopper.

‡ Feeders will increase width and depth dimensions. Please refer to feeder specifications.

One Conair Drive ● Pittsburgh, PA 15202 ● 412-312-6000 ● FAX 412-312-6227 ● www.conairnet.com

APPENDIX B