Manuals / Dell / Computer Equipment / Laptop

Dell C6145 USB Configuration, Scroll to this item and press Enter to view the following screen

Models: C6145

1 183

Download 183 pages 22.92 Kb

Page 43

Image 43

USB Configuration

Scroll to this item and press Enter to view the following screen:

Option	Description
Module Version	Displays the module version.

USB Devices Enabled	Displays USB devices currently detected.

Legacy USB Support	Select this item to enable or disable legacy USB support.
(Enabled default)
USB 2.0 Controller Mode	Configure the USB 2.0 controller in HiSpeed (480 Mbps)
(Hispeed default)	or FullSpeed (12 Mbps).
	If user uses USB device (Floppy, CDROM) to install
	RedHat Linux 9.0, please change USB 2.0 Controller
	Mode to FullSpeed to workaround it, because RedHat
	Linux 9.0 is not supported completely for hand-off
	function.

Using the System Setup Program 43

Page 43

Image 43

Dell C6145 manual USB Configuration, Scroll to this item and press Enter to view the following screen, Option, Description

Contents

Hardware Owner’s Manual Dell PowerEdge C6145 SystemsRegulatory Model B05S February Notes, Cautions, and WarningsBack Panel Features and Indicators Contents2 Using the System Setup Program Hard-Drive Indicator PatternsServer Menu Boot MenuAdvanced Menu Security MenuRecommended Tools 3 Installing System ComponentsSafety Instructions Power SuppliesExpansion-Card Assembly and Expansion Card 6 ContentsInstalling a System Board ContentsInstalling the Sensor Board for 2.5” Hard Drive System 4 Troubleshooting Your System8 Contents Installing the Sensor Board for 3.5” Hard Drive SystemSystem Board Connectors Description Accessing System Features During StartupAbout Your System KeystrokeAbout Your System Front-Panel Features and IndicatorsFigure 1-1. Front Panel−3.5” x8 Hard Drives With Two Motherboards Figure 1-2. Front Panel−3.5” x12 Hard Drives With Two Motherboards12 About Your System Figure 1-3. Front Panel−2.5” x18 Hard Drives With Two MotherboardsFigure 1-4. Front Panel−2.5” x24 Hard Drives With Two Motherboards Figure 1-5. Front Panel−2.5” x24 Hard Drives With One MotherboardIcon Indicator, ButtonOr Connector graceful shutdown before power toActivity LED Hard-Drive Indicator PatternsFigure 1-6. Hard-Drive Indicators HardFunction Back-Panel Features and IndicatorsExpander Hard DriveIcon Indicator, ButtonOr Connector Figure 1-8. Back Panel−One Motherboardsystems, turning off the system using the Indicator, ButtonOr Connector NOTE When powering on the system, theNIC Status Indicator Link/Activity NIC Indicator CodesFigure 1-9. NIC Indicators NIC Status Indicator SpeedCondition Figure 1-10. NIC Indicators BMC Management PortNIC Status Indicator Speed NIC Status Indicator Link/Activity20 About Your System Power and System Board Indicator CodesCondition Power Supply Indicator CodesFigure 1-11. Power Supply Status Indicator AC Power LED22 About Your System BMC Heart Beat LEDFigure 1-12. BMC Heart Beat LED BMC heart beat LEDCollecting System Event Log SEL for Investigation Post Error CodePost Error Code Event About Your System Other Information You May NeedSystem Setup Options at Boot Using the System Setup ProgramStart Menu Console Redirection 28 Using the System Setup Program Main Screen Main MenuUsing the System Setup Program Processor BIOS FirmwareSystem Firmware Product InformationCountDisplays the physical processor count System MemoryDisplays the total system memory size installed on the system Using the System Setup Program32 Using the System Setup Program Advanced MenuOption CPU ConfigurationDescription Description CPU ConfigurationScroll to this item and press Enter to view the following screen OptionOption Auto Mode defaultDescription Maximum Performance Power Management Maximum PerformanceOption DescriptionOption Power Management OS ControlP-state 0 default Using the System Setup ProgramDescription Power Management Advanced Platform Management Link38 Using the System Setup Program OptionOption Memory ConfigurationUsing the System Setup Program Scroll to this item and press Enter to view the following screenDescription IDE ConfigurationNative IDE default Optionfunction for that port will not work Using the System Setup ProgramOption DescriptionDescription AHCI Port042 Using the System Setup Program OptionDescription USB ConfigurationScroll to this item and press Enter to view the following screen OptionOption PCI ConfigurationOption DescriptionOption Using the System Setup ProgramDescription Description PCIE Slot/Onboard LAN/Mezzing Slot ASPM46 Using the System Setup Program OptionOption NB-SB Port FeaturesUsing the System Setup Program Scroll to this item and press Enter to view the following screen48 Using the System Setup Program Hyper Transport ConfigurationScroll to this item and press Enter to view the following screen Boot MenuThis page enables you to set POST boot parameters Using the System Setup ProgramDescription Boot Settings ConfigurationSelect this item and press Enter to view the following submenu items OptionDescription Boot Device PrioritySelect this item and press Enter to view the following submenu items Option52 Using the System Setup Program Hard Disk DrivesUsing the System Setup Program Removable DrivesScroll to this item and press Enter to view the following screen 54 Using the System Setup Program CD/DVD DrivesUsing the System Setup Program USB DrivesScroll to this item and press Enter to view the following screen 56 Using the System Setup Program Network DrivesScroll to this item and press Enter to view the following screen Security MenuThis page enables you to set the security parameters Using the System Setup ProgramOption Full Access defaultFull Access default Full Access defaultOption Server MenuPower Off default Immediate default60 Using the System Setup Program System ManagementDescription Remote Access Configuration115200 8,n,1 default OptionOption 62 Using the System Setup ProgramDescription BMC will reset IPMI ConfigurationSets the type of BMC NIC from BIOS Shared defaultDescription IP Address Configuration64 Using the System Setup Program OptionDescription Subnet Mask ConfigurationUsing the System Setup Program OptionDescription Default Gateway IP Configuration66 Using the System Setup Program OptionOption Exit MenuDescription syscfg --istokenactive=D4tokenid Command Line Interface for Setup Optionsimpitool raw command data syscfg -t=D4tokenidDescription Setup OptionUsing the System Setup Program TokenDescription Setup Option70 Using the System Setup Program TokenDescription Setup OptionUsing the System Setup Program TokenDescription Setup Option72 Using the System Setup Program TokenDescription Setup OptionUsing the System Setup Program TokenDescription Setup Option74 Using the System Setup Program TokenUsing the System Setup Program Table 2-2. The IPMI Command TableIPMI Command Setup OptionDescription IPMI CommandSetup Option 76 Using the System Setup ProgramSettings Table 2-3. The Power Management SettingsPerformance Settings Power OptimizedSafety Instructions Installing System ComponentsRecommended Tools Installing System Components Inside the Systemsystem-board assembly power distribution boardHard Drives Installing a Hard-Drive BlankRemoving a Hard-Drive Blank Removing a Hard-Drive Carrier 2 Close the release handle to lock the hard drive in place Installing a Hard-Drive CarrierRemoving a Hard Drive From a Hard-Drive Carrier 3 Turn the lock lever clockwise to the lock symbol. See Figure1 Place the hard drive into the hard-drive carrier. See Figure Installing a Hard Drive Into a Hard-Drive CarrierInstalling System Components 2 Lift the hard drive out of the hard-drive carrierTable 3-1. PSU and Motherboard Support Matrix Power SuppliesRecommended Configuration Full ConfigurationRemoving a Power Supply NOTE The maximum output power is printed on the power supply label Installing a Power Supply86 Installing System Components Removing a System-Board Assembly System-Board AssemblyAir Ducts Installing a System-Board AssemblyRemoving the Air Duct Figure 3-7. Removing and Installing the Air Ducts Installing the Air DuctRemoving the Heat Sink Heat SinksFigure 3-8. Removing and Installing the Heat Sink Installing the Heat SinkRemoving a Processor Processors3 Remove the heat sink, see Removing the Heat Sink on page Installing a Processor Removing the Expansion Card Expansion-Card Assembly and Expansion Cardlatch Figure 3-11. Removing the Expansion Card Installing the Expansion Card9 Replace the screw securing the expansion card Removing the Expansion-Card Connector Expansion-Card ConnectorInstalling the Expansion-Card Connector Removing the SAS Mezzanine Card Mezzanine CardInstalling the SAS Mezzanine Card Removing the 10GbE Mezzanine Card 104 Installing System Components Figure 3-15. Removing and Installing the 10GbE Mezzanine Cardsystem-board assembly Figure 3-16. Removing and Installing the 10GbE Mezzanine CardInstalling the 10GbE Mezzanine Card Removing the Mezzanine-Card Bridge Board Mezzanine-Card Bridge BoardSupported DIMM Configuration Installing the Mezzanine-Card Bridge BoardSystem Memory Figure 3-18. Memory Slot Locations Installing System Components Table 3-3. Memory Module Configurations and Limitation Memory Unit=GB110 Installing System Components Removing the Memory ModulesInstalling the Memory Modules 3 memory module socket ejector Figure 3-19. Installing and Removing a DIMM112 Installing System Components memory moduleReplacing the System Battery System Battery11 Exit the System Setup program Removing a System Board System BoardInstalling a System Board Opening the System Opening and Closing the SystemFigure 3-22. Opening and Closing the System Cooling FansClosing the System Removing a Cooling Fancooling fans Figure 3-23. Removing and Installing a Cooling Fan120 Installing System Components Installing a Cooling FanNOTE The fan blades should face the front panel of the system Removing a Power Distribution Board Power Distribution Boards122 Installing System Components Installing a Power Distribution BoardFigure 3-24. Removing and Installing a Power Distribution Board 2nd power distribution boardRemoving the Fan Controller Board Fan Controller Boardfan controller board Figure 3-25. Removing and Installing the Fan Controller BoardMiddle Planes Installing the Fan Controller BoardRemoving the Middle Planes 126 Installing System Components Figure 3-26. Removing and Installing the Cooling-Fan Bracketscooling-fan bracket upper middle plane Figure 3-27. Removing and Installing the Upper Middle PlaneFigure 3-28. Removing and Installing the Mid-plane Holder Support Installing System Componentsmid-plane holder Figure 3-29. Removing and Installing the Mid-plane HolderFigure 3-30. Removing and Installing the Lower Middle Plane Installing the Middle Planes130 Installing System Components Removing the 3.5 Hard-Drive Backplane Backplanes132 Installing System Components Figure 3-31. Removing and Installing the 3.5 Hard-Drive Cage3.5 hard-drive cage 3.5 hard-drive cage Figure 3-32. Removing and Installing the 3.5 Hard-Drive CageInstalling System Components front-panel assemblyInstalling the 3.5 Hard-Drive Backplane Removing the Expander Card Expander Card Optional136 Installing System Components Figure 3-34. Removing and Installing the 2.5 Hard-Drive Cage2.5 hard-drive cage Figure 3-35. Removing and Installing the Hard-Drive Cage expander card 2.5 hard-drive backplaneInstalling the Expander Card Removing the Front Panel Front Panels3-38 Figure 3-39. Removing and Installing a Front Panel Installing the Front PanelRemoving the Sensor Board for 3.5” Hard Drive System Sensor Boards144 Installing System Components Figure 3-40. Removing and Installing the Sensor Boardsensor board Installing the Sensor Board for 3.5” Hard Drive System 146 Installing System Components Removing the Sensor Board for 2.5” Hard Drive SystemInstalling System Components Figure 3-41. Removing and Installing the Sensor-Board Assemblysensor-board assembly Figure 3-42. Removing and Installing the Sensor Board148 Installing System Components Installing the Sensor Board for 2.5” Hard Drive SystemSafety First - For You and Your System Troubleshooting Your SystemInstallation Problems Troubleshooting a USB Device Troubleshooting System Startup FailureTroubleshooting External Connections Troubleshooting the Video SubsystemTroubleshooting a Serial I/O Device 152 Troubleshooting Your System Troubleshooting a NICTroubleshooting a Wet System Troubleshooting the System Battery Troubleshooting a Damaged System154 Troubleshooting Your System Troubleshooting Power Supplies Troubleshooting a Fan Troubleshooting System Cooling Problems156 Troubleshooting Your System Troubleshooting System Memory If the problem is not resolved, proceed with the next step Troubleshooting a Hard Drive 160 Troubleshooting Your System Troubleshooting a Storage ControllerTroubleshooting Expansion Cards 162 Troubleshooting Your System Troubleshooting ProcessorsIRQ Assignment Conflicts main power connector Jumpers and ConnectorsSystem Board Connectors Figure 5-1. System Board Connectors23 onboard SATAII connector 25 onboard SATAII connector 11 Hard Drive to backplane SATAII connector13 Hard Drive to backplane SATAII connector 15 Hard Drive to backplane SATAII connector 17 SGPIO connector166 Jumpers and Connectors Backplane Connectors3.5 Hard-Drive Backplane With CPLD fan controller board connectorFigure 5-4. Front View of the Backplane 2.5 Hard-Drive Backplane With ExpanderFigure 5-5. Back View of the Backplane 2.5 Hard-Drive Backplane Expander Card ConnectorsFigure 5-6. 2.5 Hard-Drive Backplane Expander Card Figure 5-7. Middle Plane Connectors Middle Plane ConnectorsPCI-E Gen 2 x16 iPass connector Expansion Card ConnectorsFigure 5-8. Expansion Card Connectors 170 Jumpers and ConnectorsSGPIO connector B SAS Mezzanine Card ConnectorsFigure 5-9. SAS Mezzanine Card Connectors Mini-SAS connectorPCI-E Gen2 x8 connector 10GbE Mezzanine Card ConnectorsFigure 5-10. 10GbE Mezzanine Card Connectors 172 Jumpers and ConnectorsFigure 5-11. Fan Controller Board Connectors Fan Controller Board ConnectorsPMbus connector Power Distribution Board ConnectorsFigure 5-12. Power Distribution Board Connectors hard-drive backplane powerJumpers and Connectors Sensor Board ConnectorsFigure 5-13. Sensor Board Connectors power connectorTable 5-1. System Configuration Switch Switch and Jumper SettingsSystem Configuration Switch Settings Figure 5-14. System Configuration SwitchTable 5-2. Jumpers Installed on 3.5 Backplane 3.5 Backplane Jumper Settings2.5 Backplane Expander Card Jumper Settings Figure 5-15. Jumpers Installed on 3.5 BackplaneJumper Figure 5-16. Jumpers Installed on Expander CardTable 5-3. Jumpers Installed on Expander Card 178 Jumpers and ConnectorsContacting Dell Getting HelpIndex Page 182 Index Index