Other Operations

•To cancel, press <ZONE2/3/4 / REC SELECT>, then turn <SOURCE SELECT> until “ZONE2 SOURCE” is displayed.

•Make a test recording before starting the actual recording.

•Signals are only output to the analog REC OUT connectors when the digital signals input to the digital input connectors (OPTICAL/ COAXIAL) are PCM (2-channel) signals.

•As the digital audio signal input from the HDMI connector is not output to the digital recording connector (OPTICAL), you should connect using the OPTICAL and COAXIAL connectors.

•Sources selected with the REC OUT mode are output from ZONE2 as well.

•In the REC OUT mode, the remote control unit’s ZONE2 mode buttons cannot be operated.

•The “XM” and “HD Radio” digital audio output signals are not output from the OPTICAL2 output connectors. Also, network audio signals (Internet radio, music server, USB, Napster and Rhapsody) are output as copy-protected signals.

NOTE

•Recordings you make are for your personal enjoyment and should not be used for other purposes without permission of the copyright holder.

•Input sources for which “Delete” is selected at “Source Delete” (vpage 53) cannot be selected.

Convenient Functions

HDMI Control Function

When you make an HDMI connection with a TV or player compatible with AVR-4810CI and HDMI control functions, you can perform the following operations by setting the HDMI control function of each device.

nAVR-4810CI power off can be linked to the TV power off step.

When you set “Output audio from amp” in the TV audio output setup operation, you can switch the amp power on.

n You can switch audio output devices with a TV operation.

nYou can adjust AVR-4810CI volume in the TV volume adjustment operation.

n You can switch AVR-4810CI input source through linkage to TV input switching.

n When playing the player, the AVR-4810CI input function switches to the function of that player.

•When you want to listen to TV audio by AVR-4810CI, connect optical digital or analog audio (vpage 21 “TV“).

•When using these functions set as follows: “HDMI Control” – “Control” (vpage 44) set to “ON“.

NOTE

•When “Control” is set to “ON”, it consumes more standby power.

•The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control.

•When you power off AVR-4810CI, the HDMI control function does not operate. Either power on or set to standby.

•Some functions may not operate depending on the connected TV or player. Check the owner’s manual of each device for details beforehand. Please refer to the DENON website for information on compatible equipment.

•When “Control” is set to “ON”, it is not possible to assign an HDMI terminal to “TV” at “Input Assign” (vpage 59).

1Turn the power on for all the equipment connected by HDMI cable.

2Set the HDMI control function for all equipment connected by HDMI cable.

Set “HDMI Control” – “Control” (vpage 44) to “ON“.

b Please consult the operating instructions for the connected equipment to check the settings.

b Carryout steps 1 and 2 should any of the equipment be plugged out.

3Switch the television input to the HDMI connected to the AVR-4810CI.

4Switch the AVR-4810CI input to the HDMI input source and check if the picture from the player is ok.

5When you turn the TV’s power to standby, check that the power of the AVR-4810CI and player also goes on standby.

If the HDMI control function does not operate properly, check the following points.

•Is the TV or player compatible with the HDMI control function?

•Is the AVR-4810CI properly set?

•Is the “HDMI Control” – “Control” (vpage 44) set to “ON”?

•Is the “Power Off Control” (vpage 44) set to “ON”?

•Is the “Control Monitor” (vpage 44) set for the monitor output connected to television?

•In the case of dual monitor connection, is the “Control Monitor” (page 44) on the GUI menu set to a monitor without HDMI control?

•Are the HDMI control function settings of all equipment correct?

NOTE

Should any of the operations below be performed, the interlocking function may be reset, in which case, repeat step’s 1 and 2.

•“Input Assign” – “HDMI” (vpage 59) setting has changed.

•“Monitor Out” (vpage 43) setting is changed.

•There is a change to the connection between the equipment and the HDMI, or an increase in equipment.

Specifications Troubleshooting Information Control Remote zone-Multi Playback Settings Connections Started Getting

99