Getting
Adjusting the Sound and Picture Quality (Audio/Video Adjust)
Setting items | Setting contents |
Setting items | Setting contents |
Playback Settings Connections Started
Tone | Tone Control : Sets the tone control function ON and OFF. |
Adjust the tonal quality of | • ON : Allow tone adjustment (treble, bass). |
the sound. | • OFF : Playback without tone adjustment. |
•This can be set when “Dynamic EQ” (vpage 92) is set to “OFF”.
•The tone cannot be adjusted in the direct mode.
Bass : Adjust low frequency range (bass).
•
This can be set when “Tone Control” is set to “ON”.
Treble : Adjust high frequency range (treble).
•
This can be set when “Tone Control” is set to “ON”.
Audyssey Settings (Continued)
Dynamic EQ : Solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics.
• ON : Use the Dynamic EQ equalizer. | ||
• OFF : Do not use the Dynamic EQ equalizer. | ||
• After performing “Audyssey Auto Setup”, the “Dynamic EQ” setting | ||
automatically becomes “ON”. | ||
• “ |
| ” is displayed when set to “ON”. |
|
|
|
• When “MultEQ XT” is set to “OFF” or “Manual”, “Dynamic EQ” is | ||
automatically set to “OFF”. | ||
• If “Dynamic Volume” is set to “ON”, “Dynamic EQ” is automatically | ||
Specifications Troubleshooting Information Control Remote
Audyssey Settings
Set MultEQ XT, Dynamic EQ and Dynamic Volume.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 38) to return to the settings after Audyssey Auto Setup was run.
MultEQ XT : Corrects both time and frequency response problems in the listening area.
•Audyssey : Optimize the frequency response of all speakers.
•Audyssey Byp.L/R : Optimize frequency response of speakers except front L and R speakers.
•Audyssey Flat : Optimize frequency response of all speakers to flat response.
•Manual : Apply frequency response set with “Manual EQ” (vpage 94).
•OFF : Turn “MultEQ XT” equalizer off.
•“Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be selected after Audyssey Auto Setup has been performed. “Audyssey” is automatically selected after performing Audyssey Auto Setup. “When
“Audyssey”,“AudysseyByp.L/R”or“AudysseyFlat”isselected,“ 
” lights.
•After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only “
” lights.
•If “Dynamic EQ” or “Dynamic Volume” is set to “ON” when “MultEQ XT” is set to either “OFF” or “Manual”, “MultEQ XT” is automatically set to “Audyssey”.
•You can also press MULTEQ XT on the main remote control unit to set.
NOTE
•“MultEQ XT” and “Manual” cannot be selected when “EQ Customize” is set to “Not Used” (vpage 45).
•When using headphones, “MultEQ XT” is set to “OFF”.
set to “ON”. |
• When you set ”Dynamic EQ” to ”ON”, “Tone Control” is switched |
”OFF”. |
• You can also press DYNAMIC EQ on the main remote control unit to |
set. |
Dynamic EQ : ON/Volume : OFF 
Dynamic EQ / Volume : OFF
“Red”“Off”
About Dynamic EQ
Audyssey Dynamic EQ™ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ® XT to provide
See overleaf
92 | Main remote control unit | :Displaying the menu | :Moves the cursor | :Confirm the setting | :Return to previous menu |
| operation buttons | Cancel the menu | (Up/Down/Left/Right) |
|
|