Specifications Troubleshooting Information Control Remote
Making Detailed Settings (Manual Setup)
nSteps for setting “Amp Assign”
Item 1 : “Configuration” settings
Select MAIN ZONE channel configuration.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5.1ch |
| 7.1ch |
|
| 9.1ch |
| 11.1ch | ||||
|
|
|
|
|
|
|
|
|
|
|
|
Item 2 : “Extra Channel” settings
Select the channels to be used from among surround back speakers (SB), front height speakers (FH), front wide speakers (FW).
| SB | FH | FW | SB/FH | SB/FW | FH/FW |
5.1ch | 5.1ch+SB |
| 5.1ch+FW | 5.1ch+SB+FW | 5.1ch+SB+FH+FW | |
|
| 5.1ch+FH |
| 5.1ch+SB+FH | 5.1ch+FH+FW | |
Determine the maximum number of channels used by the
Item 3 : “Assign Mode” settings
Select power amp usage method.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| NORMAL |
| +Z2 |
| +Z2+Z3 |
|
| ALL Z2 |
| ALL Z2+Z3 |
| FREE | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Item 4 : “Front” settings
Select front speaker connection method.Set channels assigned to power amps
(vpage 40).
NORMAL 
2CH BW 
2CH BA 
Perform the settings for each speaker using “Speaker Configuration” (vpage 41).
See page 41 for details of the settings in “Assign Mode” and “Front”.
n“Free Assign” settings
It is possible to freely select the signal being output from each speaker terminal (except for
In the screen below, press ui to select the speaker terminal, then press o p to select the output signal.
AMP ASSIGN |
| [2/2] |
| |
|
|
|
|
|
|
| TERMINAL | SIGNAL | PRE |
Config | 11.1ch | FRONT | FRONT | F |
Extra ch | SB/FH/(FW) | CENTER | CENTER | C |
Assign Mode FREE | SURR. | SURR. | S | |
|
| SB/H/W | S.BACK | SB |
|
| H/W | HEIGHT | H |
|
| SW/BA | W | |
|
| ZONE2 | SW | |
|
| ZONE3 | Z2 | |
|
|
|
| Z3 |
RETURN Return
Select the signal output from the FRONT terminals
Refer to the chart below for the signals that can be output to each speaker terminal.
|
|
| Speaker terminal |
| ||
|
|
|
|
| S.BACK / | F.HEIGHT / |
| FRONT | CENTER |
| SURROUND | F.HEIGHT / | |
|
| F.WIDE | ||||
|
|
|
|
| F.WIDE | |
|
|
|
|
|
| |
| FRONT | CENTER |
| FRONT | FRONT | FRONT |
| CENTER | S.BACK *1 |
| CENTER | CENTER | CENTER |
| SURROUND | ZONE2 |
| SURROUND | SURROUND | SURROUND |
| S.BACK *1 | ZONE3 |
| S.BACK *1 | S.BACK *1 | S.BACK *1 |
Signal | F.HEIGHT *2 | – – – |
| F.HEIGHT *2 | F.HEIGHT *2 | F.HEIGHT *2 |
F.WIDE*3 |
|
| F.WIDE*3 | F.WIDE*3 | F.WIDE*3 | |
|
|
| ||||
|
|
|
|
|
|
|
| ZONE2 |
|
| ZONE2 | ZONE2 | ZONE2 |
|
|
|
|
|
|
|
| ZONE3 |
|
| ZONE3 | ZONE3 | ZONE3 |
|
|
|
|
|
|
|
| Z2/Z3(MONO) |
|
| Z2/Z3(MONO) | Z2/Z3(MONO) | Z2/Z3(MONO) |
|
|
|
|
|
|
|
| – – – |
|
| – – – | – – – | – – – |
– –
*1 : Can be selected when “SB” is set in “Extra Channel”.
*2 : Can be selected when “FH” is set in “Extra Channel”.
*3 : Can be selected when “FW” is set in “Extra Channel”.
•When “Z2/Z3 (MONO)” is selected, ZONE2 and ZONE3 use monaural audio. The ZONE2 mono audio is output from the speaker terminal’s L ch and the ZONE3 mono audio is output from the R ch.
•When selecting “S.BACK” for the center speaker terminal output, set the “Speaker Configuration” – “Surround Back” (vpage 41) to “1spkr”.
•When selecting “ZONE2” or “ZONE3” for the center speaker terminal, set the “Zone Setup” – “Channel” (vpage 52) to “Mono”.
40 | Main remote control unit | :Displaying the menu | :Moves the cursor | :Confirm the setting | :Return to previous menu |
| operation buttons | Cancel the menu | (Up/Down/Left/Right) |
|
|