Denon AVR-4810CI 52

Making Detailed Settings (Manual Setup)

Setting items

Setting contents

Setting items

Setting contents

Network Connecting

y Use i to select “Connection” and press ENTER.

Network Connecting

q On the GUI menu, select “Network Connecting” – “Detail” and

(Continued)

Network connection starts.

(Continued)

press ENTER.

When connection is established with the access point, “Connection

w Use o p to set “DHCP” to “OFF”, then press i.

completed.” is displayed.

The DHCP function is disabled.

e Use uip to input the address and press ENTER.

NETWORK CONNECTING

• IP Address : Set the IP address within the ranges shown below.

Connection completed.

The Network Audio function cannot be used if other IP addresses

DHCP

are set.

IP Address

192.168.100.85

CLASS A: 10.0.0.0 ~ 10.255.255.255

CLASS B: 172.16.0.0 ~ 172.31.255.255

Exit

CLASS C: 192.168.0.0 ~ 192.168.255.255

Detail

• Subnet Mask : When connecting an xDSL modem or terminal

Terminate setup

Enter

adapter directly to

the AVR-4810CI, input the subnet

mask

indicated in the documentation supplied by your provider. Normally

AVR-4810CI performs automatic network setup due to the

DHCP

input 255.255.255.0.

function.

• Default Gateway : When connected to a gateway (router), input

When connecting to a network without a DHCP function, you will need

its IP address.

to manually configure the IP address.

• Primary DNS, Secondary DNS : If there is only one DNS address

For details, see page 49 “Wired LAN settings” in step 3.

indicated in the documentation supplied by your provider, input it

at “Primary DNS”. If there are two or more DNS addresses, input

Wired LAN settings

the first one at “Secondary DNS”.

Use this procedure to configure the Wired LAN settings.

r Use i to select “Exit” and press ENTER.

1. Connect the LAN cable (vpage 26 “Connecting to a Home Network

Setup is complete.

(LAN)”).

b When connecting to the network via a Proxy server, select “Proxy” and

2. Turn on the AVR-4810CI (vpage 28 “Turning the Power On”).

press ENTER (vpage 50 “Proxy settings”).

AVR-4810CI performs automatic network setup due to the DHCP

function.

When connecting to a network that has no DHCP function, perform the

• If you are using a broadband router (DHCP function), there is no need

setting in step 3.

to make the settings at “IP Address” and “Proxy”, since the DHCP

3. Set the IP address at the “Network Connecting”.

function is set to “ON” in the AVR-4810CI’s default settings.

• If the AVR-4810CI is being used connected to a network without the

NETWORK CONNECTING

DHCP function, the network settings must be made. In this case, some

DHCP

OFF

knowledge of networks

is required. For details, consult a network

DHCP

IP Address

192

. 168

. 100

. 033

administrator.

IP Address

192.168.100.33

Subnet Mask

255 . 255 . 255

. 000

Default Gateway

000 . 000 . 000

. 000

• If you cannot connect to the Internet, recheck the connections and

Primary DNS

000

. 000

settings (vpage 26).

Secondary DNS

000

. 000

Exit

Proxy

• If you do not understand about Internet connection, contact your ISP

Detail

Exit

(Internet Service Provider) or the store from which you purchased your

computer.

Enter

RETURN

Cancel

Set IP address and proxy manually

Set IP address manually

• When you want to cancel the setting during IP address input, press

RETURN.

See overleaf

Main remote control unit

:Displaying the menu

:Moves the cursor

:Confirm the setting

:Return to previous menu

operation buttons

Cancel the menu

(Up/Down/Left/Right)

Specifications Troubleshooting Information Control Remote zone-Multi Playback Settings Connections Started Getting