Getting

Make the Optimal Speaker Settings, and Correct the Room Acoustics (Audyssey™ Auto Setup)

Specifications Troubleshooting Information Control Remote zone-Multi Playback Settings Connections Started

s Audyssey Auto Setup Preparations

around items indicate the settings.

STEP1 Preparation

Perform the following settings if adjustments, etc., are required for the speaker environment you’re using.

If you do not need to perform the following settings, or have already completed them, select “Auto Setup Start” and then press ENTER. Proceed to “ STEP2 ”.

Change the Amplifier Assignment (Amp Assign)

It is possible to switch the signals being output from the Bi-Wir. or Bi- Amp, FRONT, S.BACK/F.HEIGHT/F.WIDE, F.HEIGHT/F.WIDE, ZONE2 and ZONE3 speaker terminals on the AVR-4810CI to suit the speaker environment being used (vpage 39 ~ 41 “Amp Assign”).

1Select “Amp Assign” and then press

ENTER.

2Pressing o p, select the MAIN ZONE channel configuration (“Configuration”) and then press i.

5.1ch 7.1ch 9.1ch 11.1ch

3When selecting “7.1ch” or “9.1ch” in step 2, press o pto select the channels to be used (“Extra Channel”),

and then press i.

nWhen setting “Configuration” to “7.1ch”

SB

: When using surround back channel

 

: When using front height channel

FH

 

: When using front wide channel

FW

nWhen setting “Configuration” to “9.1ch”

SB/FH

: When using surround back channel and front height

 

channel

 

: When using surround back channel and front wide

SB/FW

 

channel

FH/FW

: When using front height channel and front wide

 

channel

4Pressing o p, set the usage method for the power amp (“Assign Mode”), and then press i.

NORMAL

: This is the usual configuration.

 

: Assign a power amp to ZONE2 audio.

+Z2

 

: Assign a power amp to ZONE2 and ZONE3 audio.

+Z2+Z3

 

: Assign all power amps to ZONE2 audio.

ALL Z2

 

: Assign all power amps to ZONE2 and ZONE3 audio.

ALL Z2+Z3

 

: Freely assign power amps to the desired channels.

FREE

5Pressing o p, set the connection method for the front speakers (“Front”), and then press i.

NORMAL : This is the usual configuration.

Bi-WIRING : Bi-wire the front speakers.

Bi-AMP

: Bi-amp the front speakers.

 

: Bi-wire another front speaker for 2 channel play

2CH BW

 

mode.

2CH BA

: Bi-amp another front speaker for 2 channel play

 

mode.

The following screen is displayed.

 

 

6 The speaker terminals and the output from the pre-out terminals

can be checked on this screen.

 

 

 

 

 

 

q Current settings

 

 

 

 

w Speaker terminal name

 

 

 

e Signal being output from

 

 

 

speaker terminal

 

 

 

 

r Output

from

pre-out

 

 

 

terminal

 

 

 

 

 

b Terminals not being used

 

q

 

are greyed out.

 

w e r

b See page 14, 15 on how to connect the speakers.

•When you are using speaker terminals for multi-zone (ZONE2/ ZONE3), set “Assign Mode” to “+Z2” or “+Z2+Z3”.

•You can set in the same way as described in “Amp Assign” on page 34.

NOTE

Since “Configuration” of AVR-4810CI is set to “5.1ch” by default, audio is not output from the surround back speakers. When using the surround back speakers with MAIN ZONE, set “Configuration” to something other than “5.1ch”, and then select “SB” in “Extra Channel”.

Set the Channels You will not Use (Channel Skip)

If you set the channels you will not use beforehand, those channels will not be measured. Therefore, you can save an amount of time commensurate with that which would have been taken to measure those channels.

1 Select “Channel Skip” and then press

ENTER.

2Press ui to select a channel, press o p to select the item, and then press ENTER.

nConfigurable channels

Subwoofer : Set the subwoofer channel.

Surround Back : Set the surround back channel.

Front Height : Set the front height channel.

Front Wide : Set the front wide channel.

nSettings

Measure : Measure the selected channel.

Skip : Skip the selected channel and do not measure.

b To cancel, press RETURN.

Displayed when “Surround Back”, “Front Height” and “Front Wide” are set using “Extra Channel” in “Amp Assign”.

34

Main remote control unit

:Displaying the menu

:Moves the cursor

:Confirm the setting

:Return to previous menu

 

operation buttons

Cancel the menu

(Up/Down/Left/Right)