Ordering Information, 24 VDC | Emerson Process Management 53eA

MODEL 54eA	SECTION 1.0
	SPECIFICATIONS

1.3 ORDERING INFORMATION

The Model 54eA Microprocessor Analyzer measures dissolved oxygen, free chlorine, total chlorine, ozone, and pH. pH is available for free chlorine only. The analyzer has an on-board pressure sensor for automatic air calibration of oxygen sensors. Amperometric measurements are fully compensated for changes in membrane permeability with temperature. Free chlorine is corrected for pH. Standard features include a three-line back-lit display, dual isolated outputs, and three programmable alarm relays. HART communications and PID and TPC control are optional.

MODEL
54eA	MICROPROCESSOR ANALYZER

CODE	OPTIONS
01	115/230 VAC, 50/60 Hz Power
02	24 VDC


CODE	OPTIONS

09HART Communications Protocol

20Controller Outputs - PID and TPC

54eA -01	-20	EXAMPLE

ACCESSORIES

PART NO. DESCRIPTION

2002577 Wall and two inch pipe mounting kit

23545-00 Panel mounting kit

23554-00 Cable glands, kit (Qty 5 of PG 13.5)

9240048-00 Stainless steel tag (specify marking)

4

Image 10

Emerson Process Management 53eA instruction manual Ordering Information, 115/230 VAC, 50/60 Hz Power, 24 VDC

Contents

Model 54eA Amperometric Hart Analyzer/Controller Essential Instructions Page Model 54eA ANALYZER/CONTROLLER 12.0 10.011.0 13.0 Section Title List of FiguresIii Section Specifications Features and Applications Output Accuracy ± 0.05 mA Alarms Specifications GeneralPower Weight/Shipping Weight 5 lb/6 lb 2 kg/2.5 kg Specifications Total Chlorine Specifications OxygenSpecifications Free Chlorine Specifications Ozone Ordering Information 115/230 VAC, 50/60 Hz Power24 VDC Installation Section InstallationUnpacking and Inspection Pipe and Wall Mounting Dimensions Pipe mounting Panel Mounting Dimensions Panel mounting POWER, ALARM, and Output Wiring Section WiringGeneral 454EPH02 Wiring Model 499A oxygen, chlorine, and ozone sensors Sensor WiringGeneral 4054eA01 4054eA03 4054eA02 4054eA04 4054eA07 General Description Alarm StatusSection Display and Operation Display Section Software Configuration Program Settings List Choices Factory Settings Configure Choices Factory Settings Temperature compensation Section Menu Tree for the 54eA Controller Main Menu Main Alarm setpoints Alarm 2 setpoint MA 0.00 ppm 20 mA 20.00 ppm Output 1 12.00 mA Ranging the Outputs Simulated test Alarm setpointsOutput setpoints Setpoint 1.000 ppm 4mA 0.000 ppm 20mA 10.00 ppm Simulated tests Test alarm 1 OpenTest output Configure Display Temp units C Output 1 mA Output 2 mA Display contrast Timeout OnLanguage English Display left Display right Out Output 1 control OutputsOutput Measurement Output 1 Control Ctrl mode NormalOutput 1 Setup Range 4-20 mA Dampen 0 sec Hold Last Value Hold setup Using hold Changes in the alarm setup Changing Alarm ParametersAlways configure the control parameters Before making Alarm Control Settings Alarm 2 control Alarm 1 controlAlarm 1 setup Alarm Low Setpoint 0.000 ppm Low Alarm High Alarm Timeout 3600 sec Alarm FaultFeed limit Disable Feed limit timer setup Timer Disable Timer Time activated Interval 24.0 hr Alarm 4 setup Feed limit timerInterval timer Interval timer setup Using the 499ACL-01 sensor PH sensor EnablePH sensor Disable PH comp Manual PH value 7.00 pH Glass imp lo 20 MΩ Diagnostics OffAutocal Standard Temp coeff Operate iso 7.00 pH Sensor iso 7.00 pH Temp units C Temperature Compensation and Temperature UnitsTemp comp Auto Temp comp Manual Temp units C 60 Hz Noise Reduction Main sensor cal Bar units mm Hg Bar meas AutoBarometric Pressure Security Lock program Lock configNoise rejection Main sensor cal Lock all Condition Definitions Controller Mode PriorityAction Definitions Section Calibration Temperature Introduction Adjust temp + 025.1 C Temperature Calibration Section Calibration Dissolved Oxygen Dissolved Oxygen Concentration Sensor must be in zero solution Zeroing the Sensor Stabilizing . . . Wait Calibrating the Sensor in AIR Section Calibrate 8.32 ppm Calibrating the Sensor Against a Standard Instrument Standardize Zero main sensor Adjust temperatureCalibrate main sensor Calibrating Barometric Pressure Section Calibration Free Chlorine 499ACL-01 Sensor Current as a Function of Free Chlorine Concentration Calibrate main sensor Calibrate 1.100 ppm Full Scale Calibration Calibrate low point Dual range calOutput trim Dual Slope Calibration Low point 2.000 ppm Calibrate high point Section Calibration Free Chlorine 498CL-01 Introduction Ppm 100ppm 000 ppm Section Calibration Free Chlorine 498CL-01 Section Calibration Total Chlorine This page intentionally left blank Section Calibration Monochloramine Sensor Current as a Function of Monochloramine Concentration Ppm 100ppm Section Calibration Ozone Sensor Current as a Function of Ozone Concentration Ppm 100ppm Section PH at 25C Standards Nominal pH Autocal buffer Automatic TWO-POINT Calibration 10.02 pH Pt 04.00pH 25C Calibrate pointManual TWO-POINT Calibration 10.01 pH Pt 4.00pH 25.0C Standardization ONE-POINT Calibration Pt calibration Standardize pH pH slope PH slope 60.00 mV/pH Section Calibration Current Outputs Trimming the Outputs Section PID and TPC Control PID Control Code Control Loop Adjustment and Tuning Proportional Gain Plus Integral ResetProcess Reaction Curve Method Process Reaction Curve Section Time Proportional Control TPC Mode Code Fault message Explanation See Section Section TroubleshootingTroubleshooting When a Fault Message is Showing Overview Check sensor zero Temperature error low or highHigh input current PH low or high input voltage Sense line open Troubleshooting When no Fault Message is Showing OxygenProblem See Section Failure factory and Failure eeprom Zero current is too high Possible error warning during in-process calibrationZero reading Is unstable Readings drift Barometric pressure reading is too high or too lowProcess readings are erratic Sensor does not respond to changes in oxygen level Problem Zero current is unstable Sensor can be calibrated, but the current is too low Sensor does not respond to changes in chlorine level Chlorine readings are too low Problem See Section Sensor does not respond to changes in monochloramine level Readings are too low Troubleshooting When no Fault Message is Showing Ozone Sensor does not respond to changes in ozone level Ozone readings are too low Troubleshooting When no Fault Message is Showing pH Sensor does not respond to known pH changes Controller will not accept manual slope100 Process pH readings are noisy 101 Simulating Inputs Dissolved Oxygen Troubleshooting not Related to Measurement ProblemsProblem Action Sensor Polarizing Voltage Resistance Expected current Simulating Inputs Other Amperometric Measurements Simulate Chlorine and Ozone 103 Voltage mV PH at 25C Simulating pH input when the preamplifier is in the sensor104 Simulating temperature Simulating Temperature105 Measuring Reference Voltage 106 Section Maintenance Replacement Parts Part Number Description Section Return of Material General Warranty Specifications subject to change without notice