MODEL 54eA | SECTION 5.0 |
| SOFTWARE CONFIGURATION |
Main
FIGURE 5-1. Menu Tree for the 54eA Controller (continued)
Menu
| Calibrate | (see page 21) |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| Diagnostic Variable (see page 21) |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Program |
|
|
| Alarm Setpoints | (see page 22) |
|
|
| ||||||
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
| Output setpoints | (see page 22) |
|
|
| ||||||
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
| Simulated tests | (see page 22) |
|
|
| ||||||
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Configure |
| Display | (see page 22) | |||||||
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Outputs | (see page 22) | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Alarms | (see page 22) |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| pH |
|
|
| ||
|
|
|
|
|
|
| (available with free |
|
| ||||||
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| chlorine only) |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Temperature
Noise
Rejection
Barometric
Pressure
(oxygen only)
Main sensor cal
Security
| Disable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
| Enable |
|
| pH |
|
|
| Diagnostics: on or off |
| ||
|
|
|
| diagnostics |
|
|
| Glass impedance high |
| ||
|
|
|
|
|
|
|
| Glass impedance low |
| ||
|
|
|
|
|
|
|
| Zero offset |
|
|
|
|
|
|
|
|
|
|
| Impedance temp comp: on or off |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| pH |
|
|
| Autocal: | standard, manual, |
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| calibration |
|
|
| Merck, | Ingold, DIN 19267 |
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| Stabilize pH |
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| Stabilize time |
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
| Temperature |
|
| Temperature coeff |
|
| ||
|
|
|
| coefficient |
| Operating isopotential |
|
| |||
|
|
|
|
|
|
|
| Sensor isopotential |
|
| |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
Temperature comp: auto or manual |
|
|
|
|
| ||||||
Units: °C or °F |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Noise rejection: 50 or 60 Hz
Measurement: Auto or manual
Units: mm Hg, kPa, atm, barg, in Hg
Stabilize conc’n
Stabilize time
Salinity (oxygen only)
Lock all
Lock program
Lock configure
23
