454EPH02 | Emerson Process Management 53eA manual

MODEL 54eA	SECTION 3.0
	WIRING

DWG. NO.

454EPH02

REV.

D

FIGURE 3-1. Power Input and Relay Output Wiring for Model 54eA

9

Image 15

Emerson Process Management 53eA instruction manual 454EPH02

Contents

Amperometric Hart Analyzer/Controller Model 54eA Essential Instructions Page Model 54eA ANALYZER/CONTROLLER 13.0 10.011.0 12.0 List of Figures Section TitleIii Features and Applications Section Specifications Weight/Shipping Weight 5 lb/6 lb 2 kg/2.5 kg Specifications GeneralPower Output Accuracy ± 0.05 mA Alarms Specifications Ozone Specifications OxygenSpecifications Free Chlorine Specifications Total Chlorine 115/230 VAC, 50/60 Hz Power Ordering Information24 VDC Section Installation InstallationUnpacking and Inspection Pipe mounting Pipe and Wall Mounting Dimensions Panel mounting Panel Mounting Dimensions Section Wiring POWER, ALARM, and Output WiringGeneral 454EPH02 Sensor Wiring Wiring Model 499A oxygen, chlorine, and ozone sensorsGeneral 4054eA01 4054eA03 4054eA02 4054eA04 4054eA07 Display Alarm StatusSection Display and Operation General Description Program Settings List Section Software Configuration Choices Factory Settings Configure Choices Factory Settings Temperature compensation Section Menu Tree for the 54eA Controller Main Menu Main Alarm 2 setpoint Alarm setpoints Ranging the Outputs MA 0.00 ppm 20 mA 20.00 ppm Output 1 12.00 mA Setpoint 1.000 ppm 4mA 0.000 ppm 20mA 10.00 ppm Alarm setpointsOutput setpoints Simulated test Test alarm 1 Open Simulated testsTest output Display Configure Display contrast Timeout On Temp units C Output 1 mA Output 2 mALanguage English Display left Display right Out Outputs Output 1 controlOutput Measurement Range 4-20 mA Dampen 0 sec Hold Last Value Ctrl mode NormalOutput 1 Setup Output 1 Control Using hold Hold setup Alarm Control Settings Changing Alarm ParametersAlways configure the control parameters Before making Changes in the alarm setup Alarm Low Setpoint 0.000 ppm Alarm 1 controlAlarm 1 setup Alarm 2 control High Alarm Low Alarm Feed limit timer setup Alarm FaultFeed limit Disable Timeout 3600 sec Interval timer setup Alarm 4 setup Feed limit timerInterval timer Timer Disable Timer Time activated Interval 24.0 hr PH comp Manual PH value 7.00 pH PH sensor EnablePH sensor Disable Using the 499ACL-01 sensor Diagnostics Off Glass imp lo 20 MΩAutocal Standard Operate iso 7.00 pH Sensor iso 7.00 pH Temp coeff Temp comp Manual Temp units C Temperature Compensation and Temperature UnitsTemp comp Auto Temp units C Noise Reduction 60 Hz Main sensor cal Bar meas Auto Bar units mm HgBarometric Pressure Lock all Lock program Lock configNoise rejection Main sensor cal Security Controller Mode Priority Condition DefinitionsAction Definitions Introduction Section Calibration Temperature Temperature Calibration Adjust temp + 025.1 C Dissolved Oxygen Concentration Section Calibration Dissolved Oxygen Zeroing the Sensor Sensor must be in zero solution Calibrating the Sensor in AIR Stabilizing . . . Wait Section Calibrating the Sensor Against a Standard Instrument Calibrate 8.32 ppm Calibrating Barometric Pressure Zero main sensor Adjust temperatureCalibrate main sensor Standardize Sensor Current as a Function of Free Chlorine Concentration Section Calibration Free Chlorine 499ACL-01 Calibrate main sensor Full Scale Calibration Calibrate 1.100 ppm Dual Slope Calibration Dual range calOutput trim Calibrate low point Calibrate high point Low point 2.000 ppm Introduction Section Calibration Free Chlorine 498CL-01 Ppm 100ppm 000 ppm Section Calibration Free Chlorine 498CL-01 Section Calibration Total Chlorine This page intentionally left blank Sensor Current as a Function of Monochloramine Concentration Section Calibration Monochloramine Ppm 100ppm Sensor Current as a Function of Ozone Concentration Section Calibration Ozone Ppm 100ppm PH at 25C Standards Nominal pH Section Automatic TWO-POINT Calibration Autocal buffer 10.02 pH Calibrate point Pt 04.00pH 25CManual TWO-POINT Calibration Pt 4.00pH 25.0C 10.01 pH Pt calibration Standardize pH pH slope Standardization ONE-POINT Calibration PH slope 60.00 mV/pH Trimming the Outputs Section Calibration Current Outputs PID Control Code Section PID and TPC Control Proportional Gain Plus Integral Reset Control Loop Adjustment and TuningProcess Reaction Curve Method Process Reaction Curve Section Time Proportional Control TPC Mode Code Overview Section TroubleshootingTroubleshooting When a Fault Message is Showing Fault message Explanation See Section PH low or high input voltage Temperature error low or highHigh input current Check sensor zero Failure factory and Failure eeprom Troubleshooting When no Fault Message is Showing OxygenProblem See Section Sense line open Possible error warning during in-process calibration Zero current is too highZero reading Is unstable Sensor does not respond to changes in oxygen level Barometric pressure reading is too high or too lowProcess readings are erratic Readings drift Zero current is unstable Problem Sensor can be calibrated, but the current is too low Chlorine readings are too low Sensor does not respond to changes in chlorine level Problem See Section Sensor does not respond to changes in monochloramine level Readings are too low Troubleshooting When no Fault Message is Showing Ozone Ozone readings are too low Sensor does not respond to changes in ozone level Troubleshooting When no Fault Message is Showing pH Controller will not accept manual slope Sensor does not respond to known pH changes100 101 Process pH readings are noisy Sensor Polarizing Voltage Resistance Expected current Troubleshooting not Related to Measurement ProblemsProblem Action Simulating Inputs Dissolved Oxygen Simulate Chlorine and Ozone 103 Simulating Inputs Other Amperometric Measurements Simulating pH input when the preamplifier is in the sensor Voltage mV PH at 25C104 Simulating Temperature Simulating temperature105 106 Measuring Reference Voltage Replacement Parts Part Number Description Section Maintenance General Section Return of Material Warranty Specifications subject to change without notice