Temperature compensation Section | Emerson Process Management 53eA

MODEL 54eA	SECTION 5.0
	SOFTWARE CONFIGURATION

TABLE 5-1. Program Settings List (continued)

	ITEM	CHOICES	FACTORY SETTINGS
CONFIGURE (continued)
D. pH measurement (Section 5.8)
1. pH sensor		Enable or disable	Enable
2. pH compensation (free chlorine only)		Auto or manual	Auto
3. pH value		0.00 - 14.00	7.00
4. pH diagnostic		On or off	Off
	a. Glass impedance high	0-2000 MΩ (0 disables)	1000 MΩ
	b. Glass impedance low	0-900 MΩ (0 disables)	20 MΩ
	c. Reference impedance high	0-140 kΩ (0 disables)	140 kΩ
	d. Zero offset	0-999 mV	60 mV
	e. Impedance temp. compensation	On or off	On
5. pH calibration
	a. Auto calibration (buffer list)	Manual, Standard, Merck, Ingold, DIN 19267	Standard
	b. Stabilize pH	0.01 - 0.50	0.1
	c. Stabilization time	0-30 sec	10 sec
6.	Solution temperature coefficient
	a. Temperature coefficient	-0.044 to 0.028 pH/°C	0.000
	b. Operating isopotential	-1.35 to 20.12 pH	7.00
	c. Sensor isopotential	0 to 14 pH	7.00
E. Temperature compensation (Section 5.9)
1. Temperature compensation		Auto or manual	Auto
2.	Manual temperature	-15 to 130°C	25°C
F. Noise Reduction (section 5.10)
Noise rejection		50 or 60 Hz	60 Hz
G. Main sensor calibration (Section 5.11)
1.	Stabilize reading
	a. oxygen (ppm)	0 to 20 ppm	0.05 ppm
	b. oxygen (ppb)	0 to 999 ppb	50 ppb
	c. oxygen (% saturation)	0 to 200%	1%
	d. chlorine, monochloramine, or ozone	0 to 9999 ppm	0.05 ppm
2.	Stabilize time	0 - 30 sec	10 sec
3.	Sensor zero stabilization value
4.	Dual range calibration	Enable or disable	disable
5.	Salinity (parts per thousand)	0.0 - 99.9 o/oo	0.0 o/oo
H. Barometric Pressure (Section 5.12)
1.	Barometric pressure (oxygen only)	Auto or manual	Auto
2.	Barometric pressure manual	0.4 - 1.2 atm (or equivalent units)	1.00 atm
3.	Barometric pressure units	mm Hg, in Hg, bar, kPa	mm Hg
I. Security (Section 5.13)
1.	Lock all	000-999 (000 disables)	000
2.	Lock program	000-999 (000 disables)	000
3.	Lock configuration	000-999 (000 disables)	000

20

Image 26

Emerson Process Management 53eA instruction manual Temperature compensation Section

Contents

Model 54eA Amperometric Hart Analyzer/Controller Essential Instructions Page Model 54eA ANALYZER/CONTROLLER 12.0 10.011.0 13.0 Iii List of FiguresSection Title Section Specifications Features and Applications Output Accuracy ± 0.05 mA Alarms Specifications GeneralPower Weight/Shipping Weight 5 lb/6 lb 2 kg/2.5 kg Specifications Total Chlorine Specifications OxygenSpecifications Free Chlorine Specifications Ozone 24 VDC 115/230 VAC, 50/60 Hz PowerOrdering Information Unpacking and Inspection Section InstallationInstallation Pipe and Wall Mounting Dimensions Pipe mounting Panel Mounting Dimensions Panel mounting General Section WiringPOWER, ALARM, and Output Wiring 454EPH02 General Sensor WiringWiring Model 499A oxygen, chlorine, and ozone sensors 4054eA01 4054eA03 4054eA02 4054eA04 4054eA07 General Description Alarm StatusSection Display and Operation Display Section Software Configuration Program Settings List Choices Factory Settings Configure Choices Factory Settings Temperature compensation Section Menu Tree for the 54eA Controller Main Menu Main Alarm setpoints Alarm 2 setpoint MA 0.00 ppm 20 mA 20.00 ppm Output 1 12.00 mA Ranging the Outputs Simulated test Alarm setpointsOutput setpoints Setpoint 1.000 ppm 4mA 0.000 ppm 20mA 10.00 ppm Test output Test alarm 1 OpenSimulated tests Configure Display Language English Display left Display right Out Display contrast Timeout OnTemp units C Output 1 mA Output 2 mA Output Measurement OutputsOutput 1 control Output 1 Control Ctrl mode NormalOutput 1 Setup Range 4-20 mA Dampen 0 sec Hold Last Value Hold setup Using hold Changes in the alarm setup Changing Alarm ParametersAlways configure the control parameters Before making Alarm Control Settings Alarm 2 control Alarm 1 controlAlarm 1 setup Alarm Low Setpoint 0.000 ppm Low Alarm High Alarm Timeout 3600 sec Alarm FaultFeed limit Disable Feed limit timer setup Timer Disable Timer Time activated Interval 24.0 hr Alarm 4 setup Feed limit timerInterval timer Interval timer setup Using the 499ACL-01 sensor PH sensor EnablePH sensor Disable PH comp Manual PH value 7.00 pH Autocal Standard Diagnostics OffGlass imp lo 20 MΩ Temp coeff Operate iso 7.00 pH Sensor iso 7.00 pH Temp units C Temperature Compensation and Temperature UnitsTemp comp Auto Temp comp Manual Temp units C 60 Hz Noise Reduction Main sensor cal Barometric Pressure Bar meas AutoBar units mm Hg Security Lock program Lock configNoise rejection Main sensor cal Lock all Action Definitions Controller Mode PriorityCondition Definitions Section Calibration Temperature Introduction Adjust temp + 025.1 C Temperature Calibration Section Calibration Dissolved Oxygen Dissolved Oxygen Concentration Sensor must be in zero solution Zeroing the Sensor Stabilizing . . . Wait Calibrating the Sensor in AIR Section Calibrate 8.32 ppm Calibrating the Sensor Against a Standard Instrument Standardize Zero main sensor Adjust temperatureCalibrate main sensor Calibrating Barometric Pressure Section Calibration Free Chlorine 499ACL-01 Sensor Current as a Function of Free Chlorine Concentration Calibrate main sensor Calibrate 1.100 ppm Full Scale Calibration Calibrate low point Dual range calOutput trim Dual Slope Calibration Low point 2.000 ppm Calibrate high point Section Calibration Free Chlorine 498CL-01 Introduction Ppm 100ppm 000 ppm Section Calibration Free Chlorine 498CL-01 Section Calibration Total Chlorine This page intentionally left blank Section Calibration Monochloramine Sensor Current as a Function of Monochloramine Concentration Ppm 100ppm Section Calibration Ozone Sensor Current as a Function of Ozone Concentration Ppm 100ppm Section PH at 25C Standards Nominal pH Autocal buffer Automatic TWO-POINT Calibration 10.02 pH Manual TWO-POINT Calibration Calibrate pointPt 04.00pH 25C 10.01 pH Pt 4.00pH 25.0C Standardization ONE-POINT Calibration Pt calibration Standardize pH pH slope PH slope 60.00 mV/pH Section Calibration Current Outputs Trimming the Outputs Section PID and TPC Control PID Control Code Process Reaction Curve Method Proportional Gain Plus Integral ResetControl Loop Adjustment and Tuning Process Reaction Curve Section Time Proportional Control TPC Mode Code Fault message Explanation See Section Section TroubleshootingTroubleshooting When a Fault Message is Showing Overview Check sensor zero Temperature error low or highHigh input current PH low or high input voltage Sense line open Troubleshooting When no Fault Message is Showing OxygenProblem See Section Failure factory and Failure eeprom Zero reading Is unstable Possible error warning during in-process calibrationZero current is too high Readings drift Barometric pressure reading is too high or too lowProcess readings are erratic Sensor does not respond to changes in oxygen level Problem Zero current is unstable Sensor can be calibrated, but the current is too low Sensor does not respond to changes in chlorine level Chlorine readings are too low Problem See Section Sensor does not respond to changes in monochloramine level Readings are too low Troubleshooting When no Fault Message is Showing Ozone Sensor does not respond to changes in ozone level Ozone readings are too low Troubleshooting When no Fault Message is Showing pH 100 Controller will not accept manual slopeSensor does not respond to known pH changes Process pH readings are noisy 101 Simulating Inputs Dissolved Oxygen Troubleshooting not Related to Measurement ProblemsProblem Action Sensor Polarizing Voltage Resistance Expected current Simulating Inputs Other Amperometric Measurements Simulate Chlorine and Ozone 103 104 Simulating pH input when the preamplifier is in the sensorVoltage mV PH at 25C 105 Simulating TemperatureSimulating temperature Measuring Reference Voltage 106 Section Maintenance Replacement Parts Part Number Description Section Return of Material General Warranty Specifications subject to change without notice