Msgid 0432 Debug Ring Reset | Emulex LP1150-F4 guide

MSG_ID: 0432 Debug: Ring Reset

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates an SLI ring is being reset.

SEVERITY LEVEL: Debug

MESSAGE: Ring reset

ACTION: No action needed, informational.

MSG_ID: 0440 Debug: Adapter Msg

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that a message was sent to the driver from the adapter.

SEVERITY LEVEL: Debug

MESSAGE: Adapter msg

ACTION: No action needed, informational.

MSG_ID: 0450 Error: IOCB Invalid

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that an IOCB was received from the adapter with an illegal value. This error could indicate a driver or firmware problem.

SEVERITY LEVEL: Error

MESSAGE: IOCB invalid

ACTION: No action needed. If problems persist, report these errors to Technical Support.

MSG_ID: 0451 Debug: IOCB Queue Full

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that the IOCB queue is full. This will occur during normal operation.

SEVERITY LEVEL: Debug

MESSAGE: IOCB queue full

ACTION: No action needed, informational.

MSG_ID: 0452 Debug: IOCB Error

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates an IOCB local error is being reported by the adapter.

SEVERITY LEVEL: Debug

MESSAGE: IOCB error

ACTION: No action needed, informational.

MSG_ID: 0453 Debug: IOCB Stale

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates an IOCB completed after its associated packet completed.

SEVERITY LEVEL: Debug

MESSAGE: IOCB stale

ACTION: No action needed, informational.

MSG_ID: 0460 Debug: SLI Detail

VERBOSE_MASK: LOG_SLI _DETAIL (0x20000000)

DESCRIPTION: This provides detailed information about an SLI event.

SEVERITY LEVEL: Debug

MESSAGE: SLI detail

ACTION: No action needed, informational.

Solaris SFS Driver User Manual

Page 147

Image 154

Emulex LP1150-F4 user manual Msgid 0432 Debug Ring Reset, Msgid 0440 Debug Adapter Msg, Msgid 0450 Error Iocb Invalid

Contents

Solaris SFS Driver Last Updated June 14 Starting the HBAnyware Utility from the Command Line Downloading and Installing the Driver for Solaris 8 orRemoving the Utilities Using the emlxuremove Script Using the HBAnyware Utility Command-Line InterfacePage 104 Using the emlxdrv Utility 124 Introduction 131 Situations That Involve HBAnyware Introduction 161 Console and Log Messages 139Use Cases 161 Compatibility HBA Compatibility Known Issues Procedure Method 2 Using Individual Patches Downloading and Installing the Driver for Solaris 8 orMethod 1 Using the Installit Script recommended To obtain and install individual patchesPage Installing the FCA Utilities Unpacking the Utility Files Prerequisites To install the utilities kit using the emlxuinstall scriptEmlxuinstall script is available Enter y. The following message is displayed JRE and instructions for installation can be found at Installing the HBAnyware UtilityKnown Issues Unzip the HBAnyware package file. Type To install HBAnyware with Web Launch Log on as ‘root’ Installing the HBAnyware Utility with Web LaunchRun the install script. Type Compatibility Installing the HBAnyware Utility Security ConfiguratorInstalling or Updating the Utilities Package Manually Unzip the HBAnywareSSC package file Removing the Utilities Using the emlxuremove Script Removing the Utilities Package Manually To remove the emlxu utilities package Configuration Driver Parameters Solaris SFS and lpfc Driver Parameter Cross-Reference Table Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Starting the HBAnyware Utility Starting the HBAnyware Security ConfiguratorProcedure Starting HBAnyware with Web Launch Enter desired management mode Press Enter Click OK Changing Management ModeStarting the HBAnyware Utility from the Command Line Examples of Modifications Menu Bar HBAnyware Utility Window Element DefinitionsToolbar Discovery-Tree Toolbar ButtonsSort Toolbar Buttons Status Bar Using the HBAnyware Utility Command-Line InterfaceProperty Tabs Discovery-Tree Icons Out-of-Band Access Using the CLI ClientSyntax Rules ListHBAs CLI Client Command Reference VersionSaveConfig Sample response HBAAttrib PortAttrib ServerAttrib PortStatParameters Reset TargetMapping AllNodeInfo DriverConfigDownload Sample response for a successful download DriverParamsGlobal DriverParamsSample abbreviated response SetDriverParam SetBootBios PciData GetBeacon WakeupLoopMap Below is a sample response PostTest SetBeaconEchoTest Dump LoopbackDeleteDumpFiles PersistentBinding SetPersistentBinding RemovePersistentBinding RemoveAllPersistentBindingSample response would be BindingSupport BindingCapabilitiesSetBindingSupport Discovering HBAs HBAnyware Utility, Discovery Information Configuring Discovery Settings HBAnyware Utility, HBA Discovery Settings Dialog Box Sorting by Host Name Sorting HBAsSorting Local HBAs Only Sorting by Fabric Address Viewing Discovery Information Viewing HBA InformationDiscovery Information Field Definitions Host Information Tab Viewing Host InformationHost Information Field Definitions Driver Parameter Tab Field Definitions Host Driver Parameters TabDriver Parameter Tab Buttons Viewing General HBA Attributes Adapter Summary Field Definitions Adapter Status Area Field Definitions Adapter Details Field Definitions Viewing Detailed HBA InformationPort Attributes Field Definitions Viewing Fabric Information Loop Map Table Definitions Discovery Information Field Definitions Viewing Target InformationTarget Information Field Definitions Viewing LUN Information LUN Information Field Definitions Viewing Port Statistics HBAnyware Utility, Statistics Tab Port Statistics Field Definitions Firmware Field Definitions Enable/Disable Click to enable or disable the boot codeViewing Firmware Information Firmware Area Viewing Target Mapping Target Mapping Field Definitions Resetting HBAs Updating Firmware Following warning screen appears HBAnyware Utility, Firmware Download Dialog Box Click Browse. The Firmware File Selection dialog box appears Click Start Download Updating Firmware Batch Mode HBAnyware Utility, Batch Firmware Download Dialog Box Enabling or Disabling the Bios Solaris SFS driver is installed properly Setting Driver Parameters HBAnyware Utility, Firmware Tab with Bios Disabled Setting Driver Parameters for an HBA HBAnyware Utility, HBA Selected Driver Parameters Tab Resetting All Default Values Setting Driver Parameters for a HostRestoring All Parameters to Their Earlier Values Restoring All Parameters to Their Earlier Values Creating the Batch Mode Driver Parameters File Assigning Batch Mode Parameters to HBAs Setting Up Persistent Binding HBAnyware Utility, Batch Driver Parameters Update Dialog Box Click the Target Mapping tab. All targets are displayed HBAnyware Utility, Add Persistent Binding Dialog Box Changing Parameters or Bindings for Solaris 8, 9 Adding New Targets Using sd.conf for Solaris 8, 9Save the file and exit No-Reboot Firmware Updates Setting Up Target/LUN Blocking Using sd.confLoading or Unloading the Driver Without Rebooting Performing Diagnostic Tests Running a Quick Test Running a Post Test Using BeaconingClick OK. a Post Test window shows Post test information Displaying PCI Registers and Wakeup Information Creating Diagnostic DumpsClick Start Dump Running Advanced Diagnostic Tests HBAnyware Utility, Advanced Diagnostics Dialog Box HBAnyware Utility, Advanced Diagnostic Tests Warning Running Loopback Tests Running End-to-End Echo Tests Saving the Log File Click Start. The following warning window appears Out-of-Band SAN Management An example of a saved log file appears below Adding a Single Host HBAnyware Utility, Add Remote Host Dialog Box Adding a Range of Hosts HBAnyware Utility, Add Remote Hosts Window Removing Hosts HBAnyware SecurityIntroduction Page Security Configurator, Unsecure System Message Unsecure System message is displayedPage Access Control Groups Access Control Group Tab on the MSC Access Control Group Tab on a Non-MSC ACG Icons Adding a Server to the ACG Deleting a Server from the ACG Removing Security from all Servers in the ACG Click Yes. Security is removed from all servers in the ACG Generating New Security Keys Restoring the ACG to Its Last Saved Configuration Accessing a Switch Access Sub-Groups ASG Icons Click New. The New Access Sub-Group dialog box is displayed Creating an ASG Reserved Indices Examples ASG Creation Example Adding a Server to an ASG Deleting an ASG Restoring an ASG to Its Last Saved Configuration Security Configurator, Edit Access Sub Group Dialog Box Editing an ASG About Offline ASGs Backup Masters Backup Master Eligible Systems Creating a Backup Master Backup Master Tab and Controls Reassigning a Backup Master as the New MSC from the Old MSC System16 as Backup Master Click the Backup Master tab Security Configurator, Backup Master Warning Dialog Box Interactive Mode emlxadm Modes of Operation emlxadm CLI Mode emlxadm Information similar to the following is displayed # emlxadm SUNW,emlxs@2 getnumdevs Getnumdevs Command Descriptions emlxadmGetdevlist Getlogiparams wwpn Returns the FC login parameters of this HBA port ExampleGethostparams Setsympname string Devlogin wwpnGetsympname Getsymnname Devremove wwpn Devlogout wwpnGetstate wwpn Linkstatus did Downloadfw filename Downloadfcode filenameGetfwrev Downloads the specified FCode image file to the HBA Example Getdumpsize GetbootrevDownloadboot filename Forcedump Forces the HBA to perform a hardware reset Example Resetlink wwpn or zero for local linkResethard Gettopology Forces the HBA to perform a core firmware reset Example ResethardcoreDiag test parameters or diag code cmdcode hex Returns the total number of configurable parameters Example Parmgetnum Returns a list of configurable parameters Example ParmgetlistPage Parmset label value Parmget labelExample This example attempts to set a static parameter Gethostattrs Msgbuf all or number -i intervalDisplays all of the current host HBA API attributes Example Getportattrs index, wwn or all = Seagate ST39103FC Getpath index Getvpd Bootcode enable or disableDisplays a help menu of utility commands Example Exits the utility program Example Repeats the last command Example Hba Modes of Operation emlxdrv Interactive Mode emlxdrvEmlxdrv utility program can be run in two modes Interactive CLI Mode emlxdrv Setemlxssun Command Descriptions emlxdrvSetemlxs alias Setemlxsall Setlpfcnonsun Setlpfc aliasCleardev alias Clearlpfc Clearemlxs Clearsun Clearnonsun Clearall General Situations General Situations SAN Management Workstation Does Not Security Configurator Situations Access Control Groups ACG Access Control Groups Situations Security Configuration Situations Access Sub-Groups ASG HBAnyware Security Configurator Access Sub-Groups Situations HBAnyware Security Configurator Backup Masters Situations HBAnyware Security Configurator Situations Backup MastersCannot modify the Security Configurator Error Message Situations Error Message SituationsFollowing error message is displayed when Master Security Client Situations Master Security Client Situations Master Security Client Situations Introduction Log Message Types Severity Levels Severity LevelsMessage Log Example Following is an example of a message on the system console Msgid 0001 Debug Msgid 0004 ErrorMiscellaneous Events Msgid 0002 Notice Driver Events HBA Initialization Events Msgid 0202 Debug Adapter Initialization Msgid 0201 Error Adapter Initialization FailedMsgid 0240 Error Adapter Reset Failed Msgid 0210 Debug Adapter Transition Memory Management Events Service Level Interface SLI Events Msgid 0452 Debug Iocb Error Msgid 0432 Debug Ring ResetMsgid 0450 Error Iocb Invalid Msgid 0440 Debug Adapter Msg Mailbox Events Node Events Msgid 0610 Debug Node Destroy Msgid 0603 Debug Node UpdatedMsgid 0602 Notice Node Create Failed Msgid 0611 Debug Node Closed Link Events ELS Events General I/O Packet Events Msgid 0911 Debug TXQ Watchdog Msgid 0922 Notice Packet Flush TimeoutMsgid 0931 Error Packet Transport Error Msgid 0920 Debug Packet Flush FCP Traffic Events IP Traffic Events Solaris SFS Events Msgid 1312 Warning Echo Diagnostic Failed Msgid 1310 Warning Diagnostic ErrorMsgid 1311 Debug Echo Diagnostic Completed Msgid 1313 Debug BIU Diagnostic Completed Ioctl Events Firmware Download Events Common Transport Events Msgid 1621 Debug Unsolicited CT dropped Msgid 1630 Error Invalid CT command foundMsgid 1622 Debug CT reply Use Cases Different use cases will drive different migration scenarios Sample Script File Details Operational Differences Between lpfc and SFSStartemlxsmigration.sh Finishemlxsmigration.sh Things to Know Before You Migrate Migrating a Configuration without FC BootMigrating Automatically Limitations Migrating Manually Migrating a Configuration with FC Boot Migrating Non-emlxs HBAs to emlxs HBAs For an Emulex boot HBA Shut down the server and get to the ok prompt