Emulex LP1150-F4 instruction

b.Go to http://sunsolve.sun.com/pub-cgi/show.pl?target=patchpage. Enter and download the fol- lowing required patches:

•113040

•119914

•113043

c.Follow the instructions to install each patch.

d.For additional functionality, install the following optional patches:

•113041 (FCIP)

•113039 (mpxio)

•114478 and 114477 (Common HBA API)

•114476 (FCSM)

Downloading and Installing the Driver for Solaris 10 (Sparc, X64 and x86)

If the Solaris SFS driver is not already installed, obtain and install the Solaris 10 packages. To obtain and install the Solaris 10 packages:

1.Go to http://www.sun.com/download/products.xml?id=42c4317d and click Download.

2.Log in with your user name and password, and accept the license agreement.

3.Select and download the driver package.

4.Select and download the readme file, and follow its instructions.

To finish the installation (or if the Solaris SFS driver was already installed), install the driver by obtaining and installing individual patches:

1.Go to http://sunsolve.sun.com/pub-cgi/show.pl?target=patchpage. Enter and download the following required patches:

•For SPARC systems:

•119130

•120222

•For x64 and x86 systems:

•119131

•120223

2.Follow the instructions to install each patch.

3.For additional functionality, install the following optional patches:

•For SPARC systems:

•119470 (Sun Enterprise Network Array firmware and utilities)

•119715 (scsi_vhci patch)

•For x64 and x86 systems:

•119471 (Sun Enterprise Network Array firmware and utilities)

•119715 (scsi_vhci patch)

Solaris SFS Driver User Manual

Page 4

Image 11

Emulex LP1150-F4 user manual

Contents

Solaris SFS Driver Last Updated June 14 Using the HBAnyware Utility Command-Line Interface Downloading and Installing the Driver for Solaris 8 orRemoving the Utilities Using the emlxuremove Script Starting the HBAnyware Utility from the Command LinePage 104 Introduction 131 Situations That Involve HBAnyware Using the emlxdrv Utility 124 Use Cases 161 Console and Log Messages 139Introduction 161 HBA Compatibility Compatibility Procedure Known Issues To obtain and install individual patches Downloading and Installing the Driver for Solaris 8 orMethod 1 Using the Installit Script recommended Method 2 Using Individual PatchesPage Unpacking the Utility Files Installing the FCA Utilities Enter y. The following message is displayed To install the utilities kit using the emlxuinstall scriptEmlxuinstall script is available Prerequisites Unzip the HBAnyware package file. Type Installing the HBAnyware UtilityKnown Issues JRE and instructions for installation can be found at Run the install script. Type Installing the HBAnyware Utility with Web LaunchTo install HBAnyware with Web Launch Log on as ‘root’ Unzip the HBAnywareSSC package file Installing the HBAnyware Utility Security ConfiguratorInstalling or Updating the Utilities Package Manually Compatibility Removing the Utilities Using the emlxuremove Script To remove the emlxu utilities package Removing the Utilities Package Manually Configuration Driver Parameters Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Table Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Starting HBAnyware with Web Launch Starting the HBAnyware Security ConfiguratorProcedure Starting the HBAnyware Utility Examples of Modifications Changing Management ModeStarting the HBAnyware Utility from the Command Line Enter desired management mode Press Enter Click OK Toolbar HBAnyware Utility Window Element DefinitionsMenu Bar Sort Toolbar Buttons Toolbar ButtonsDiscovery-Tree Discovery-Tree Icons Using the HBAnyware Utility Command-Line InterfaceProperty Tabs Status Bar Syntax Rules Using the CLI ClientOut-of-Band Access Sample response CLI Client Command Reference VersionSaveConfig ListHBAs PortAttrib HBAAttrib Parameters PortStatServerAttrib TargetMapping Reset Sample response for a successful download DriverConfigDownload AllNodeInfo Sample abbreviated response DriverParamsDriverParamsGlobal SetDriverParam PciData SetBootBios Below is a sample response WakeupLoopMap GetBeacon EchoTest SetBeaconPostTest DeleteDumpFiles LoopbackDump SetPersistentBinding PersistentBinding Sample response would be RemoveAllPersistentBindingRemovePersistentBinding SetBindingSupport BindingCapabilitiesBindingSupport HBAnyware Utility, Discovery Information Discovering HBAs HBAnyware Utility, HBA Discovery Settings Dialog Box Configuring Discovery Settings Sorting by Fabric Address Sorting HBAsSorting Local HBAs Only Sorting by Host Name Discovery Information Field Definitions Viewing HBA InformationViewing Discovery Information Host Information Field Definitions Viewing Host InformationHost Information Tab Driver Parameter Tab Buttons Host Driver Parameters TabDriver Parameter Tab Field Definitions Adapter Summary Field Definitions Viewing General HBA Attributes Adapter Status Area Field Definitions Port Attributes Field Definitions Viewing Detailed HBA InformationAdapter Details Field Definitions Loop Map Table Definitions Viewing Fabric Information Target Information Field Definitions Viewing Target InformationDiscovery Information Field Definitions LUN Information Field Definitions Viewing LUN Information HBAnyware Utility, Statistics Tab Viewing Port Statistics Port Statistics Field Definitions Firmware Area Enable/Disable Click to enable or disable the boot codeViewing Firmware Information Firmware Field Definitions Target Mapping Field Definitions Viewing Target Mapping Resetting HBAs Following warning screen appears Updating Firmware HBAnyware Utility, Firmware Download Dialog Box Click Start Download Click Browse. The Firmware File Selection dialog box appears HBAnyware Utility, Batch Firmware Download Dialog Box Updating Firmware Batch Mode Solaris SFS driver is installed properly Enabling or Disabling the Bios HBAnyware Utility, Firmware Tab with Bios Disabled Setting Driver Parameters HBAnyware Utility, HBA Selected Driver Parameters Tab Setting Driver Parameters for an HBA Restoring All Parameters to Their Earlier Values Setting Driver Parameters for a HostResetting All Default Values Restoring All Parameters to Their Earlier Values Assigning Batch Mode Parameters to HBAs Creating the Batch Mode Driver Parameters File HBAnyware Utility, Batch Driver Parameters Update Dialog Box Setting Up Persistent Binding Click the Target Mapping tab. All targets are displayed HBAnyware Utility, Add Persistent Binding Dialog Box Save the file and exit Adding New Targets Using sd.conf for Solaris 8, 9Changing Parameters or Bindings for Solaris 8, 9 Loading or Unloading the Driver Without Rebooting Setting Up Target/LUN Blocking Using sd.confNo-Reboot Firmware Updates Running a Quick Test Performing Diagnostic Tests Click OK. a Post Test window shows Post test information Using BeaconingRunning a Post Test Click Start Dump Creating Diagnostic DumpsDisplaying PCI Registers and Wakeup Information HBAnyware Utility, Advanced Diagnostics Dialog Box Running Advanced Diagnostic Tests Running Loopback Tests HBAnyware Utility, Advanced Diagnostic Tests Warning Running End-to-End Echo Tests Click Start. The following warning window appears Saving the Log File An example of a saved log file appears below Out-of-Band SAN Management HBAnyware Utility, Add Remote Host Dialog Box Adding a Single Host HBAnyware Utility, Add Remote Hosts Window Adding a Range of Hosts Introduction HBAnyware SecurityRemoving Hosts Page Unsecure System message is displayed Security Configurator, Unsecure System MessagePage Access Control Group Tab on the MSC Access Control Groups ACG Icons Access Control Group Tab on a Non-MSC Adding a Server to the ACG Deleting a Server from the ACG Click Yes. Security is removed from all servers in the ACG Removing Security from all Servers in the ACG Generating New Security Keys Restoring the ACG to Its Last Saved Configuration Accessing a Switch ASG Icons Access Sub-Groups Creating an ASG Click New. The New Access Sub-Group dialog box is displayed ASG Creation Example Reserved Indices Examples Deleting an ASG Adding a Server to an ASG Restoring an ASG to Its Last Saved Configuration Editing an ASG Security Configurator, Edit Access Sub Group Dialog Box About Offline ASGs Backup Master Eligible Systems Backup Masters Backup Master Tab and Controls Creating a Backup Master System16 as Backup Master Reassigning a Backup Master as the New MSC from the Old MSC Click the Backup Master tab Security Configurator, Backup Master Warning Dialog Box Modes of Operation emlxadm Interactive Mode emlxadm Information similar to the following is displayed CLI Mode emlxadm # emlxadm SUNW,emlxs@2 getnumdevs Getdevlist Command Descriptions emlxadmGetnumdevs Gethostparams Returns the FC login parameters of this HBA port ExampleGetlogiparams wwpn Getsymnname Devlogin wwpnGetsympname Setsympname string Linkstatus did Devlogout wwpnGetstate wwpn Devremove wwpn Downloads the specified FCode image file to the HBA Example Downloadfcode filenameGetfwrev Downloadfw filename Forcedump GetbootrevDownloadboot filename Getdumpsize Gettopology Resetlink wwpn or zero for local linkResethard Forces the HBA to perform a hardware reset Example Diag test parameters or diag code cmdcode hex ResethardcoreForces the HBA to perform a core firmware reset Example Parmgetnum Returns the total number of configurable parameters Example Parmgetlist Returns a list of configurable parameters ExamplePage Example This example attempts to set a static parameter Parmget labelParmset label value Displays all of the current host HBA API attributes Example Msgbuf all or number -i intervalGethostattrs = Seagate ST39103FC Getportattrs index, wwn or all Getpath index Exits the utility program Example Bootcode enable or disableDisplays a help menu of utility commands Example Getvpd Hba Repeats the last command Example Emlxdrv utility program can be run in two modes Interactive Interactive Mode emlxdrvModes of Operation emlxdrv CLI Mode emlxdrv Setemlxsall Command Descriptions emlxdrvSetemlxs alias Setemlxssun Cleardev alias Setlpfc aliasSetlpfcnonsun Clearemlxs Clearlpfc Clearnonsun Clearsun Clearall General Situations General Situations SAN Management Workstation Does Not Access Control Groups Situations Security Configurator Situations Access Control Groups ACG HBAnyware Security Configurator Access Sub-Groups Situations Security Configuration Situations Access Sub-Groups ASG Cannot modify the Security Configurator HBAnyware Security Configurator Situations Backup MastersHBAnyware Security Configurator Backup Masters Situations Following error message is displayed when Error Message SituationsError Message Situations Master Security Client Situations Master Security Client Situations Master Security Client Situations Log Message Types Introduction Following is an example of a message on the system console Severity LevelsMessage Log Example Severity Levels Msgid 0002 Notice Msgid 0004 ErrorMiscellaneous Events Msgid 0001 Debug Driver Events HBA Initialization Events Msgid 0210 Debug Adapter Transition Msgid 0201 Error Adapter Initialization FailedMsgid 0240 Error Adapter Reset Failed Msgid 0202 Debug Adapter Initialization Memory Management Events Service Level Interface SLI Events Msgid 0440 Debug Adapter Msg Msgid 0432 Debug Ring ResetMsgid 0450 Error Iocb Invalid Msgid 0452 Debug Iocb Error Node Events Mailbox Events Msgid 0611 Debug Node Closed Msgid 0603 Debug Node UpdatedMsgid 0602 Notice Node Create Failed Msgid 0610 Debug Node Destroy Link Events ELS Events General I/O Packet Events Msgid 0920 Debug Packet Flush Msgid 0922 Notice Packet Flush TimeoutMsgid 0931 Error Packet Transport Error Msgid 0911 Debug TXQ Watchdog IP Traffic Events FCP Traffic Events Solaris SFS Events Msgid 1313 Debug BIU Diagnostic Completed Msgid 1310 Warning Diagnostic ErrorMsgid 1311 Debug Echo Diagnostic Completed Msgid 1312 Warning Echo Diagnostic Failed Ioctl Events Firmware Download Events Common Transport Events Msgid 1622 Debug CT reply Msgid 1630 Error Invalid CT command foundMsgid 1621 Debug Unsolicited CT dropped Different use cases will drive different migration scenarios Use Cases Startemlxsmigration.sh Operational Differences Between lpfc and SFSSample Script File Details Finishemlxsmigration.sh Limitations Migrating a Configuration without FC BootMigrating Automatically Things to Know Before You Migrate Migrating Manually Migrating Non-emlxs HBAs to emlxs HBAs Migrating a Configuration with FC Boot Shut down the server and get to the ok prompt For an Emulex boot HBA