Viewing General HBA Attributes | Emulex LP1150-F4 instruction

Viewing General HBA Attributes

The General tab contains general attributes associated with the selected HBA. To view general attributes:

1.Start the HBAnyware utility.

2.Select Host or Fabric sort.

3.Click an HBA in the discovery-tree.

Figure 9: HBAnyware Utility, General Tab

Adapter Summary Field Definitions

•Model - The complete model name of the HBA.

•Port WWN - The Port World Wide Name of the HBA.

•Node WWN - the Node World Wide Name of the selected HBA.

•Fabric Name or Host Name - The Fabric Name field shows if you selected, “Sort by Host Name”. The fabric name is a 64-bit worldwide unique identifier assigned to the fabric. The Host Name field shows if you selected “Sort by Fabric ID”. The host name is the name of the host containing the HBA.

•Driver Version - The version of the driver installed for the HBA.

•Firmware Version - The version of Emulex firmware currently active on the HBA.

•Driver Name - The executable file image name for the driver as it appears in the Emulex driver download package.

•Boot Bios - Indicates if the boot code is enabled or disabled.

Solaris SFS Driver User Manual

Page 44

Image 51

Emulex LP1150-F4 user manual Viewing General HBA Attributes, Adapter Summary Field Definitions

Contents

Solaris SFS Driver Last Updated June 14 Using the HBAnyware Utility Command-Line Interface Downloading and Installing the Driver for Solaris 8 orRemoving the Utilities Using the emlxuremove Script Starting the HBAnyware Utility from the Command LinePage 104 Introduction 131 Situations That Involve HBAnyware Using the emlxdrv Utility 124 Console and Log Messages 139 Introduction 161Use Cases 161 HBA Compatibility Compatibility Procedure Known Issues To obtain and install individual patches Downloading and Installing the Driver for Solaris 8 orMethod 1 Using the Installit Script recommended Method 2 Using Individual PatchesPage Unpacking the Utility Files Installing the FCA Utilities Enter y. The following message is displayed To install the utilities kit using the emlxuinstall scriptEmlxuinstall script is available Prerequisites Unzip the HBAnyware package file. Type Installing the HBAnyware UtilityKnown Issues JRE and instructions for installation can be found at Installing the HBAnyware Utility with Web Launch To install HBAnyware with Web Launch Log on as ‘root’Run the install script. Type Unzip the HBAnywareSSC package file Installing the HBAnyware Utility Security ConfiguratorInstalling or Updating the Utilities Package Manually Compatibility Removing the Utilities Using the emlxuremove Script To remove the emlxu utilities package Removing the Utilities Package Manually Configuration Driver Parameters Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Table Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Starting HBAnyware with Web Launch Starting the HBAnyware Security ConfiguratorProcedure Starting the HBAnyware Utility Examples of Modifications Changing Management ModeStarting the HBAnyware Utility from the Command Line Enter desired management mode Press Enter Click OK HBAnyware Utility Window Element Definitions Menu BarToolbar Toolbar Buttons Discovery-TreeSort Toolbar Buttons Discovery-Tree Icons Using the HBAnyware Utility Command-Line InterfaceProperty Tabs Status Bar Using the CLI Client Out-of-Band AccessSyntax Rules Sample response CLI Client Command Reference VersionSaveConfig ListHBAs PortAttrib HBAAttrib PortStat ServerAttribParameters TargetMapping Reset Sample response for a successful download DriverConfigDownload AllNodeInfo DriverParams DriverParamsGlobalSample abbreviated response SetDriverParam PciData SetBootBios Below is a sample response WakeupLoopMap GetBeacon SetBeacon PostTestEchoTest Loopback DumpDeleteDumpFiles SetPersistentBinding PersistentBinding RemoveAllPersistentBinding RemovePersistentBindingSample response would be BindingCapabilities BindingSupportSetBindingSupport HBAnyware Utility, Discovery Information Discovering HBAs HBAnyware Utility, HBA Discovery Settings Dialog Box Configuring Discovery Settings Sorting by Fabric Address Sorting HBAsSorting Local HBAs Only Sorting by Host Name Viewing HBA Information Viewing Discovery InformationDiscovery Information Field Definitions Viewing Host Information Host Information TabHost Information Field Definitions Host Driver Parameters Tab Driver Parameter Tab Field DefinitionsDriver Parameter Tab Buttons Adapter Summary Field Definitions Viewing General HBA Attributes Adapter Status Area Field Definitions Viewing Detailed HBA Information Adapter Details Field DefinitionsPort Attributes Field Definitions Loop Map Table Definitions Viewing Fabric Information Viewing Target Information Discovery Information Field DefinitionsTarget Information Field Definitions LUN Information Field Definitions Viewing LUN Information HBAnyware Utility, Statistics Tab Viewing Port Statistics Port Statistics Field Definitions Firmware Area Enable/Disable Click to enable or disable the boot codeViewing Firmware Information Firmware Field Definitions Target Mapping Field Definitions Viewing Target Mapping Resetting HBAs Following warning screen appears Updating Firmware HBAnyware Utility, Firmware Download Dialog Box Click Start Download Click Browse. The Firmware File Selection dialog box appears HBAnyware Utility, Batch Firmware Download Dialog Box Updating Firmware Batch Mode Solaris SFS driver is installed properly Enabling or Disabling the Bios HBAnyware Utility, Firmware Tab with Bios Disabled Setting Driver Parameters HBAnyware Utility, HBA Selected Driver Parameters Tab Setting Driver Parameters for an HBA Setting Driver Parameters for a Host Resetting All Default ValuesRestoring All Parameters to Their Earlier Values Restoring All Parameters to Their Earlier Values Assigning Batch Mode Parameters to HBAs Creating the Batch Mode Driver Parameters File HBAnyware Utility, Batch Driver Parameters Update Dialog Box Setting Up Persistent Binding Click the Target Mapping tab. All targets are displayed HBAnyware Utility, Add Persistent Binding Dialog Box Adding New Targets Using sd.conf for Solaris 8, 9 Changing Parameters or Bindings for Solaris 8, 9Save the file and exit Setting Up Target/LUN Blocking Using sd.conf No-Reboot Firmware UpdatesLoading or Unloading the Driver Without Rebooting Running a Quick Test Performing Diagnostic Tests Using Beaconing Running a Post TestClick OK. a Post Test window shows Post test information Creating Diagnostic Dumps Displaying PCI Registers and Wakeup InformationClick Start Dump HBAnyware Utility, Advanced Diagnostics Dialog Box Running Advanced Diagnostic Tests Running Loopback Tests HBAnyware Utility, Advanced Diagnostic Tests Warning Running End-to-End Echo Tests Click Start. The following warning window appears Saving the Log File An example of a saved log file appears below Out-of-Band SAN Management HBAnyware Utility, Add Remote Host Dialog Box Adding a Single Host HBAnyware Utility, Add Remote Hosts Window Adding a Range of Hosts HBAnyware Security Removing HostsIntroduction Page Unsecure System message is displayed Security Configurator, Unsecure System MessagePage Access Control Group Tab on the MSC Access Control Groups ACG Icons Access Control Group Tab on a Non-MSC Adding a Server to the ACG Deleting a Server from the ACG Click Yes. Security is removed from all servers in the ACG Removing Security from all Servers in the ACG Generating New Security Keys Restoring the ACG to Its Last Saved Configuration Accessing a Switch ASG Icons Access Sub-Groups Creating an ASG Click New. The New Access Sub-Group dialog box is displayed ASG Creation Example Reserved Indices Examples Deleting an ASG Adding a Server to an ASG Restoring an ASG to Its Last Saved Configuration Editing an ASG Security Configurator, Edit Access Sub Group Dialog Box About Offline ASGs Backup Master Eligible Systems Backup Masters Backup Master Tab and Controls Creating a Backup Master System16 as Backup Master Reassigning a Backup Master as the New MSC from the Old MSC Click the Backup Master tab Security Configurator, Backup Master Warning Dialog Box Modes of Operation emlxadm Interactive Mode emlxadm Information similar to the following is displayed CLI Mode emlxadm # emlxadm SUNW,emlxs@2 getnumdevs Command Descriptions emlxadm GetnumdevsGetdevlist Returns the FC login parameters of this HBA port Example Getlogiparams wwpnGethostparams Getsymnname Devlogin wwpnGetsympname Setsympname string Linkstatus did Devlogout wwpnGetstate wwpn Devremove wwpn Downloads the specified FCode image file to the HBA Example Downloadfcode filenameGetfwrev Downloadfw filename Forcedump GetbootrevDownloadboot filename Getdumpsize Gettopology Resetlink wwpn or zero for local linkResethard Forces the HBA to perform a hardware reset Example Resethardcore Forces the HBA to perform a core firmware reset ExampleDiag test parameters or diag code cmdcode hex Parmgetnum Returns the total number of configurable parameters Example Parmgetlist Returns a list of configurable parameters ExamplePage Parmget label Parmset label valueExample This example attempts to set a static parameter Msgbuf all or number -i interval GethostattrsDisplays all of the current host HBA API attributes Example = Seagate ST39103FC Getportattrs index, wwn or all Getpath index Exits the utility program Example Bootcode enable or disableDisplays a help menu of utility commands Example Getvpd Hba Repeats the last command Example Interactive Mode emlxdrv Modes of Operation emlxdrvEmlxdrv utility program can be run in two modes Interactive CLI Mode emlxdrv Setemlxsall Command Descriptions emlxdrvSetemlxs alias Setemlxssun Setlpfc alias SetlpfcnonsunCleardev alias Clearemlxs Clearlpfc Clearnonsun Clearsun Clearall General Situations General Situations SAN Management Workstation Does Not Access Control Groups Situations Security Configurator Situations Access Control Groups ACG HBAnyware Security Configurator Access Sub-Groups Situations Security Configuration Situations Access Sub-Groups ASG HBAnyware Security Configurator Situations Backup Masters HBAnyware Security Configurator Backup Masters SituationsCannot modify the Security Configurator Error Message Situations Error Message SituationsFollowing error message is displayed when Master Security Client Situations Master Security Client Situations Master Security Client Situations Log Message Types Introduction Following is an example of a message on the system console Severity LevelsMessage Log Example Severity Levels Msgid 0002 Notice Msgid 0004 ErrorMiscellaneous Events Msgid 0001 Debug Driver Events HBA Initialization Events Msgid 0210 Debug Adapter Transition Msgid 0201 Error Adapter Initialization FailedMsgid 0240 Error Adapter Reset Failed Msgid 0202 Debug Adapter Initialization Memory Management Events Service Level Interface SLI Events Msgid 0440 Debug Adapter Msg Msgid 0432 Debug Ring ResetMsgid 0450 Error Iocb Invalid Msgid 0452 Debug Iocb Error Node Events Mailbox Events Msgid 0611 Debug Node Closed Msgid 0603 Debug Node UpdatedMsgid 0602 Notice Node Create Failed Msgid 0610 Debug Node Destroy Link Events ELS Events General I/O Packet Events Msgid 0920 Debug Packet Flush Msgid 0922 Notice Packet Flush TimeoutMsgid 0931 Error Packet Transport Error Msgid 0911 Debug TXQ Watchdog IP Traffic Events FCP Traffic Events Solaris SFS Events Msgid 1313 Debug BIU Diagnostic Completed Msgid 1310 Warning Diagnostic ErrorMsgid 1311 Debug Echo Diagnostic Completed Msgid 1312 Warning Echo Diagnostic Failed Ioctl Events Firmware Download Events Common Transport Events Msgid 1630 Error Invalid CT command found Msgid 1621 Debug Unsolicited CT droppedMsgid 1622 Debug CT reply Different use cases will drive different migration scenarios Use Cases Operational Differences Between lpfc and SFS Sample Script File DetailsStartemlxsmigration.sh Finishemlxsmigration.sh Limitations Migrating a Configuration without FC BootMigrating Automatically Things to Know Before You Migrate Migrating Manually Migrating Non-emlxs HBAs to emlxs HBAs Migrating a Configuration with FC Boot Shut down the server and get to the ok prompt For an Emulex boot HBA