Service Level Interface SLI Events | Emulex LP1150-F4 specs

Service Level Interface (SLI) Events

MSG_ID: 0400 Debug: Vital Product Data

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This provides vendor-specific information about the adapter.

SEVERITY LEVEL: Debug

MESSAGE: Vital Product Data

ACTION: No action needed, informational.

MSG_ID: 0410 Debug: Link Attention

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that the adapter has triggered a link attention interrupt.

SEVERITY LEVEL: Debug

MESSAGE: Link attn

ACTION: No action needed, informational.

MSG_ID: 0411 Debug: State Change

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that the adapter has changed state.

SEVERITY LEVEL: Debug

MESSAGE: State change

ACTION: No action needed, informational.

MSG_ID: 0420 Error: Adapter Hardware Error

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that an interrupt has occurred and the status register indicates a nonrecoverable hardware error.

SEVERITY LEVEL: Error

MESSAGE: Adapter hardware error

ACTION: This error usually indicates a hardware problem with the adapter. Try running adapter diagnostics. Report these errors to Technical Support.

MSG_ID: 0430 Debug: Ring Event

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that an SLI ring event has occurred.

SEVERITY LEVEL: Debug

MESSAGE: Ring event

ACTION: No action needed, informational.

MSG_ID: 0431 Debug: Ring Error

VERBOSE_MASK: LOG_SLI (0x00000010)

DESCRIPTION: This indicates that an SLI ring error is being reported by the adapter.

SEVERITY LEVEL: Debug

MESSAGE: Ring error

ACTION: No action needed, informational.

Solaris SFS Driver User Manual

Page 146

Image 153

Emulex LP1150-F4 user manual Service Level Interface SLI Events

Contents

Solaris SFS Driver Last Updated June 14 Removing the Utilities Using the emlxuremove Script Downloading and Installing the Driver for Solaris 8 orStarting the HBAnyware Utility from the Command Line Using the HBAnyware Utility Command-Line InterfacePage 104 Introduction 131 Situations That Involve HBAnyware Using the emlxdrv Utility 124 Console and Log Messages 139 Introduction 161Use Cases 161 HBA Compatibility Compatibility Procedure Known Issues Method 1 Using the Installit Script recommended Downloading and Installing the Driver for Solaris 8 orMethod 2 Using Individual Patches To obtain and install individual patchesPage Unpacking the Utility Files Installing the FCA Utilities Emlxuinstall script is available To install the utilities kit using the emlxuinstall scriptPrerequisites Enter y. The following message is displayed Known Issues Installing the HBAnyware UtilityJRE and instructions for installation can be found at Unzip the HBAnyware package file. Type Installing the HBAnyware Utility with Web Launch To install HBAnyware with Web Launch Log on as ‘root’Run the install script. Type Installing or Updating the Utilities Package Manually Installing the HBAnyware Utility Security ConfiguratorCompatibility Unzip the HBAnywareSSC package file Removing the Utilities Using the emlxuremove Script To remove the emlxu utilities package Removing the Utilities Package Manually Configuration Driver Parameters Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Table Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Procedure Starting the HBAnyware Security ConfiguratorStarting the HBAnyware Utility Starting HBAnyware with Web Launch Starting the HBAnyware Utility from the Command Line Changing Management ModeEnter desired management mode Press Enter Click OK Examples of Modifications HBAnyware Utility Window Element Definitions Menu BarToolbar Toolbar Buttons Discovery-TreeSort Toolbar Buttons Property Tabs Using the HBAnyware Utility Command-Line InterfaceStatus Bar Discovery-Tree Icons Using the CLI Client Out-of-Band AccessSyntax Rules SaveConfig CLI Client Command Reference VersionListHBAs Sample response PortAttrib HBAAttrib PortStat ServerAttribParameters TargetMapping Reset Download DriverConfigAllNodeInfo Sample response for a successful download DriverParams DriverParamsGlobalSample abbreviated response SetDriverParam PciData SetBootBios LoopMap WakeupGetBeacon Below is a sample response SetBeacon PostTestEchoTest Loopback DumpDeleteDumpFiles SetPersistentBinding PersistentBinding RemoveAllPersistentBinding RemovePersistentBindingSample response would be BindingCapabilities BindingSupportSetBindingSupport HBAnyware Utility, Discovery Information Discovering HBAs HBAnyware Utility, HBA Discovery Settings Dialog Box Configuring Discovery Settings Sorting Local HBAs Only Sorting HBAsSorting by Host Name Sorting by Fabric Address Viewing HBA Information Viewing Discovery InformationDiscovery Information Field Definitions Viewing Host Information Host Information TabHost Information Field Definitions Host Driver Parameters Tab Driver Parameter Tab Field DefinitionsDriver Parameter Tab Buttons Adapter Summary Field Definitions Viewing General HBA Attributes Adapter Status Area Field Definitions Viewing Detailed HBA Information Adapter Details Field DefinitionsPort Attributes Field Definitions Loop Map Table Definitions Viewing Fabric Information Viewing Target Information Discovery Information Field DefinitionsTarget Information Field Definitions LUN Information Field Definitions Viewing LUN Information HBAnyware Utility, Statistics Tab Viewing Port Statistics Port Statistics Field Definitions Viewing Firmware Information Enable/Disable Click to enable or disable the boot codeFirmware Field Definitions Firmware Area Target Mapping Field Definitions Viewing Target Mapping Resetting HBAs Following warning screen appears Updating Firmware HBAnyware Utility, Firmware Download Dialog Box Click Start Download Click Browse. The Firmware File Selection dialog box appears HBAnyware Utility, Batch Firmware Download Dialog Box Updating Firmware Batch Mode Solaris SFS driver is installed properly Enabling or Disabling the Bios HBAnyware Utility, Firmware Tab with Bios Disabled Setting Driver Parameters HBAnyware Utility, HBA Selected Driver Parameters Tab Setting Driver Parameters for an HBA Setting Driver Parameters for a Host Resetting All Default ValuesRestoring All Parameters to Their Earlier Values Restoring All Parameters to Their Earlier Values Assigning Batch Mode Parameters to HBAs Creating the Batch Mode Driver Parameters File HBAnyware Utility, Batch Driver Parameters Update Dialog Box Setting Up Persistent Binding Click the Target Mapping tab. All targets are displayed HBAnyware Utility, Add Persistent Binding Dialog Box Adding New Targets Using sd.conf for Solaris 8, 9 Changing Parameters or Bindings for Solaris 8, 9Save the file and exit Setting Up Target/LUN Blocking Using sd.conf No-Reboot Firmware UpdatesLoading or Unloading the Driver Without Rebooting Running a Quick Test Performing Diagnostic Tests Using Beaconing Running a Post TestClick OK. a Post Test window shows Post test information Creating Diagnostic Dumps Displaying PCI Registers and Wakeup InformationClick Start Dump HBAnyware Utility, Advanced Diagnostics Dialog Box Running Advanced Diagnostic Tests Running Loopback Tests HBAnyware Utility, Advanced Diagnostic Tests Warning Running End-to-End Echo Tests Click Start. The following warning window appears Saving the Log File An example of a saved log file appears below Out-of-Band SAN Management HBAnyware Utility, Add Remote Host Dialog Box Adding a Single Host HBAnyware Utility, Add Remote Hosts Window Adding a Range of Hosts HBAnyware Security Removing HostsIntroduction Page Unsecure System message is displayed Security Configurator, Unsecure System MessagePage Access Control Group Tab on the MSC Access Control Groups ACG Icons Access Control Group Tab on a Non-MSC Adding a Server to the ACG Deleting a Server from the ACG Click Yes. Security is removed from all servers in the ACG Removing Security from all Servers in the ACG Generating New Security Keys Restoring the ACG to Its Last Saved Configuration Accessing a Switch ASG Icons Access Sub-Groups Creating an ASG Click New. The New Access Sub-Group dialog box is displayed ASG Creation Example Reserved Indices Examples Deleting an ASG Adding a Server to an ASG Restoring an ASG to Its Last Saved Configuration Editing an ASG Security Configurator, Edit Access Sub Group Dialog Box About Offline ASGs Backup Master Eligible Systems Backup Masters Backup Master Tab and Controls Creating a Backup Master System16 as Backup Master Reassigning a Backup Master as the New MSC from the Old MSC Click the Backup Master tab Security Configurator, Backup Master Warning Dialog Box Modes of Operation emlxadm Interactive Mode emlxadm Information similar to the following is displayed CLI Mode emlxadm # emlxadm SUNW,emlxs@2 getnumdevs Command Descriptions emlxadm GetnumdevsGetdevlist Returns the FC login parameters of this HBA port Example Getlogiparams wwpnGethostparams Getsympname Devlogin wwpnSetsympname string Getsymnname Getstate wwpn Devlogout wwpnDevremove wwpn Linkstatus did Getfwrev Downloadfcode filenameDownloadfw filename Downloads the specified FCode image file to the HBA Example Downloadboot filename GetbootrevGetdumpsize Forcedump Resethard Resetlink wwpn or zero for local linkForces the HBA to perform a hardware reset Example Gettopology Resethardcore Forces the HBA to perform a core firmware reset ExampleDiag test parameters or diag code cmdcode hex Parmgetnum Returns the total number of configurable parameters Example Parmgetlist Returns a list of configurable parameters ExamplePage Parmget label Parmset label valueExample This example attempts to set a static parameter Msgbuf all or number -i interval GethostattrsDisplays all of the current host HBA API attributes Example = Seagate ST39103FC Getportattrs index, wwn or all Getpath index Displays a help menu of utility commands Example Bootcode enable or disableGetvpd Exits the utility program Example Hba Repeats the last command Example Interactive Mode emlxdrv Modes of Operation emlxdrvEmlxdrv utility program can be run in two modes Interactive CLI Mode emlxdrv Setemlxs alias Command Descriptions emlxdrvSetemlxssun Setemlxsall Setlpfc alias SetlpfcnonsunCleardev alias Clearemlxs Clearlpfc Clearnonsun Clearsun Clearall General Situations General Situations SAN Management Workstation Does Not Access Control Groups Situations Security Configurator Situations Access Control Groups ACG HBAnyware Security Configurator Access Sub-Groups Situations Security Configuration Situations Access Sub-Groups ASG HBAnyware Security Configurator Situations Backup Masters HBAnyware Security Configurator Backup Masters SituationsCannot modify the Security Configurator Error Message Situations Error Message SituationsFollowing error message is displayed when Master Security Client Situations Master Security Client Situations Master Security Client Situations Log Message Types Introduction Message Log Example Severity LevelsSeverity Levels Following is an example of a message on the system console Miscellaneous Events Msgid 0004 ErrorMsgid 0001 Debug Msgid 0002 Notice Driver Events HBA Initialization Events Msgid 0240 Error Adapter Reset Failed Msgid 0201 Error Adapter Initialization FailedMsgid 0202 Debug Adapter Initialization Msgid 0210 Debug Adapter Transition Memory Management Events Service Level Interface SLI Events Msgid 0450 Error Iocb Invalid Msgid 0432 Debug Ring ResetMsgid 0452 Debug Iocb Error Msgid 0440 Debug Adapter Msg Node Events Mailbox Events Msgid 0602 Notice Node Create Failed Msgid 0603 Debug Node UpdatedMsgid 0610 Debug Node Destroy Msgid 0611 Debug Node Closed Link Events ELS Events General I/O Packet Events Msgid 0931 Error Packet Transport Error Msgid 0922 Notice Packet Flush TimeoutMsgid 0911 Debug TXQ Watchdog Msgid 0920 Debug Packet Flush IP Traffic Events FCP Traffic Events Solaris SFS Events Msgid 1311 Debug Echo Diagnostic Completed Msgid 1310 Warning Diagnostic ErrorMsgid 1312 Warning Echo Diagnostic Failed Msgid 1313 Debug BIU Diagnostic Completed Ioctl Events Firmware Download Events Common Transport Events Msgid 1630 Error Invalid CT command found Msgid 1621 Debug Unsolicited CT droppedMsgid 1622 Debug CT reply Different use cases will drive different migration scenarios Use Cases Operational Differences Between lpfc and SFS Sample Script File DetailsStartemlxsmigration.sh Finishemlxsmigration.sh Migrating Automatically Migrating a Configuration without FC BootThings to Know Before You Migrate Limitations Migrating Manually Migrating Non-emlxs HBAs to emlxs HBAs Migrating a Configuration with FC Boot Shut down the server and get to the ok prompt For an Emulex boot HBA