SetBootBios, PciData | Emulex LP1150-F4 specs

Sample response:

Set Driver Parameter log_verbose=3(g) for 10:00:00:00:c9:2e:51:2e

Parameters:

WWPN - The World Wide Port Name of the HBA whose Boot BIOS you want to modify. This HBA can be either local or remote.

ctrlword - G = make change global, B = make change both permanent and global, N = make change neither permanent nor global

param - The name of the parameter whose value you want to modify. You can only use the log_verbose, use_adisc and _nodev_tmo parameters. Do not precede these commands with lpfc_. For example use log_verbose not lpfc_log_verbose.

Value - The new value you want to assign to the parameter.

SetBootBios

Syntax: HBACMD SetBootBios <wwpn> <ctrlword>

Description: Enables or disables the Boot BIOS on the referenced HBA. To enable the Boot BIOS for 10:00:00:00:c9:2e:51:2e, type:

hbacmd setbootbios 10:00:00:00:c9:2e:51:2e E

Parameters:

WWPN - The World Wide Port Name of the HBA whose Boot BIOS you want to modify. This HBA can be either local or remote.

ctrlword - E = enable the Boot BIOS, D = disable the Boot BIOS.

PciData

Syntax: HBACMD PciData <wwpn>

Description: Shows PCI configuration data for the HBA specified by the WWPN. To show PCI configuration data for HBA 10:00:00:00:c9:2e:51:2e, type:

hbacmd pcidata 10:00:00:00:c9:2e:51:2e

Sample response:

Vendor ID:		0x10DF	Device ID:	0xF0D5
Command:		0x0157	Status:	0x0230
Revision ID:		0x01	Prog If:	0x00
Subclass:		0x04	Base Class:	0x0C
Cache Line Size:		0x20	Latency Timer:	0xF8
Header Type:		0x00	Built In Self Test:	0x00
Base Address	0:	0xE0001004	Base Address 1:	0x00000000
Base Address	2:	0xE0000004	Base Address 3:	0x00000000
Base Address	4:	0x0000C001	Base Address 5:	0x00000000
CIS:		0x00000000	SubVendor ID:	0x10DF
SubSystem ID:		0xF0D5	ROM Base Address:	0x00000000
Interrupt Line:		0xFF	Interrupt Pin:	0x01
Minimum Grant:		0xFF	Maximum Latency:	0x00
Capabilities	Ptr:	0x5C

Parameters:

WWPN - The World Wide Port Name of the HBA whose PCI configuration data you want to show.

Solaris SFS Driver User Manual

Page 31

Image 38

Emulex LP1150-F4 user manual SetBootBios, PciData

Contents

Solaris SFS Driver Last Updated June 14 Starting the HBAnyware Utility from the Command Line Downloading and Installing the Driver for Solaris 8 orRemoving the Utilities Using the emlxuremove Script Using the HBAnyware Utility Command-Line InterfacePage 104 Using the emlxdrv Utility 124 Introduction 131 Situations That Involve HBAnyware Use Cases 161 Console and Log Messages 139Introduction 161 Compatibility HBA Compatibility Known Issues Procedure Method 2 Using Individual Patches Downloading and Installing the Driver for Solaris 8 orMethod 1 Using the Installit Script recommended To obtain and install individual patchesPage Installing the FCA Utilities Unpacking the Utility Files Prerequisites To install the utilities kit using the emlxuinstall scriptEmlxuinstall script is available Enter y. The following message is displayed JRE and instructions for installation can be found at Installing the HBAnyware UtilityKnown Issues Unzip the HBAnyware package file. Type Run the install script. Type Installing the HBAnyware Utility with Web LaunchTo install HBAnyware with Web Launch Log on as ‘root’ Compatibility Installing the HBAnyware Utility Security ConfiguratorInstalling or Updating the Utilities Package Manually Unzip the HBAnywareSSC package file Removing the Utilities Using the emlxuremove Script Removing the Utilities Package Manually To remove the emlxu utilities package Configuration Driver Parameters Solaris SFS and lpfc Driver Parameter Cross-Reference Table Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Solaris SFS and lpfc Driver Parameter Cross-Reference Starting the HBAnyware Utility Starting the HBAnyware Security ConfiguratorProcedure Starting HBAnyware with Web Launch Enter desired management mode Press Enter Click OK Changing Management ModeStarting the HBAnyware Utility from the Command Line Examples of Modifications Toolbar HBAnyware Utility Window Element DefinitionsMenu Bar Sort Toolbar Buttons Toolbar ButtonsDiscovery-Tree Status Bar Using the HBAnyware Utility Command-Line InterfaceProperty Tabs Discovery-Tree Icons Syntax Rules Using the CLI ClientOut-of-Band Access ListHBAs CLI Client Command Reference VersionSaveConfig Sample response HBAAttrib PortAttrib Parameters PortStatServerAttrib Reset TargetMapping AllNodeInfo DriverConfigDownload Sample response for a successful download Sample abbreviated response DriverParamsDriverParamsGlobal SetDriverParam SetBootBios PciData GetBeacon WakeupLoopMap Below is a sample response EchoTest SetBeaconPostTest DeleteDumpFiles LoopbackDump PersistentBinding SetPersistentBinding Sample response would be RemoveAllPersistentBindingRemovePersistentBinding SetBindingSupport BindingCapabilitiesBindingSupport Discovering HBAs HBAnyware Utility, Discovery Information Configuring Discovery Settings HBAnyware Utility, HBA Discovery Settings Dialog Box Sorting by Host Name Sorting HBAsSorting Local HBAs Only Sorting by Fabric Address Discovery Information Field Definitions Viewing HBA InformationViewing Discovery Information Host Information Field Definitions Viewing Host InformationHost Information Tab Driver Parameter Tab Buttons Host Driver Parameters TabDriver Parameter Tab Field Definitions Viewing General HBA Attributes Adapter Summary Field Definitions Adapter Status Area Field Definitions Port Attributes Field Definitions Viewing Detailed HBA InformationAdapter Details Field Definitions Viewing Fabric Information Loop Map Table Definitions Target Information Field Definitions Viewing Target InformationDiscovery Information Field Definitions Viewing LUN Information LUN Information Field Definitions Viewing Port Statistics HBAnyware Utility, Statistics Tab Port Statistics Field Definitions Firmware Field Definitions Enable/Disable Click to enable or disable the boot codeViewing Firmware Information Firmware Area Viewing Target Mapping Target Mapping Field Definitions Resetting HBAs Updating Firmware Following warning screen appears HBAnyware Utility, Firmware Download Dialog Box Click Browse. The Firmware File Selection dialog box appears Click Start Download Updating Firmware Batch Mode HBAnyware Utility, Batch Firmware Download Dialog Box Enabling or Disabling the Bios Solaris SFS driver is installed properly Setting Driver Parameters HBAnyware Utility, Firmware Tab with Bios Disabled Setting Driver Parameters for an HBA HBAnyware Utility, HBA Selected Driver Parameters Tab Restoring All Parameters to Their Earlier Values Setting Driver Parameters for a HostResetting All Default Values Restoring All Parameters to Their Earlier Values Creating the Batch Mode Driver Parameters File Assigning Batch Mode Parameters to HBAs Setting Up Persistent Binding HBAnyware Utility, Batch Driver Parameters Update Dialog Box Click the Target Mapping tab. All targets are displayed HBAnyware Utility, Add Persistent Binding Dialog Box Save the file and exit Adding New Targets Using sd.conf for Solaris 8, 9Changing Parameters or Bindings for Solaris 8, 9 Loading or Unloading the Driver Without Rebooting Setting Up Target/LUN Blocking Using sd.confNo-Reboot Firmware Updates Performing Diagnostic Tests Running a Quick Test Click OK. a Post Test window shows Post test information Using BeaconingRunning a Post Test Click Start Dump Creating Diagnostic DumpsDisplaying PCI Registers and Wakeup Information Running Advanced Diagnostic Tests HBAnyware Utility, Advanced Diagnostics Dialog Box HBAnyware Utility, Advanced Diagnostic Tests Warning Running Loopback Tests Running End-to-End Echo Tests Saving the Log File Click Start. The following warning window appears Out-of-Band SAN Management An example of a saved log file appears below Adding a Single Host HBAnyware Utility, Add Remote Host Dialog Box Adding a Range of Hosts HBAnyware Utility, Add Remote Hosts Window Introduction HBAnyware SecurityRemoving Hosts Page Security Configurator, Unsecure System Message Unsecure System message is displayedPage Access Control Groups Access Control Group Tab on the MSC Access Control Group Tab on a Non-MSC ACG Icons Adding a Server to the ACG Deleting a Server from the ACG Removing Security from all Servers in the ACG Click Yes. Security is removed from all servers in the ACG Generating New Security Keys Restoring the ACG to Its Last Saved Configuration Accessing a Switch Access Sub-Groups ASG Icons Click New. The New Access Sub-Group dialog box is displayed Creating an ASG Reserved Indices Examples ASG Creation Example Adding a Server to an ASG Deleting an ASG Restoring an ASG to Its Last Saved Configuration Security Configurator, Edit Access Sub Group Dialog Box Editing an ASG About Offline ASGs Backup Masters Backup Master Eligible Systems Creating a Backup Master Backup Master Tab and Controls Reassigning a Backup Master as the New MSC from the Old MSC System16 as Backup Master Click the Backup Master tab Security Configurator, Backup Master Warning Dialog Box Interactive Mode emlxadm Modes of Operation emlxadm CLI Mode emlxadm Information similar to the following is displayed # emlxadm SUNW,emlxs@2 getnumdevs Getdevlist Command Descriptions emlxadmGetnumdevs Gethostparams Returns the FC login parameters of this HBA port ExampleGetlogiparams wwpn Setsympname string Devlogin wwpnGetsympname Getsymnname Devremove wwpn Devlogout wwpnGetstate wwpn Linkstatus did Downloadfw filename Downloadfcode filenameGetfwrev Downloads the specified FCode image file to the HBA Example Getdumpsize GetbootrevDownloadboot filename Forcedump Forces the HBA to perform a hardware reset Example Resetlink wwpn or zero for local linkResethard Gettopology Diag test parameters or diag code cmdcode hex ResethardcoreForces the HBA to perform a core firmware reset Example Returns the total number of configurable parameters Example Parmgetnum Returns a list of configurable parameters Example ParmgetlistPage Example This example attempts to set a static parameter Parmget labelParmset label value Displays all of the current host HBA API attributes Example Msgbuf all or number -i intervalGethostattrs Getportattrs index, wwn or all = Seagate ST39103FC Getpath index Getvpd Bootcode enable or disableDisplays a help menu of utility commands Example Exits the utility program Example Repeats the last command Example Hba Emlxdrv utility program can be run in two modes Interactive Interactive Mode emlxdrvModes of Operation emlxdrv CLI Mode emlxdrv Setemlxssun Command Descriptions emlxdrvSetemlxs alias Setemlxsall Cleardev alias Setlpfc aliasSetlpfcnonsun Clearlpfc Clearemlxs Clearsun Clearnonsun Clearall General Situations General Situations SAN Management Workstation Does Not Security Configurator Situations Access Control Groups ACG Access Control Groups Situations Security Configuration Situations Access Sub-Groups ASG HBAnyware Security Configurator Access Sub-Groups Situations Cannot modify the Security Configurator HBAnyware Security Configurator Situations Backup MastersHBAnyware Security Configurator Backup Masters Situations Following error message is displayed when Error Message SituationsError Message Situations Master Security Client Situations Master Security Client Situations Master Security Client Situations Introduction Log Message Types Severity Levels Severity LevelsMessage Log Example Following is an example of a message on the system console Msgid 0001 Debug Msgid 0004 ErrorMiscellaneous Events Msgid 0002 Notice Driver Events HBA Initialization Events Msgid 0202 Debug Adapter Initialization Msgid 0201 Error Adapter Initialization FailedMsgid 0240 Error Adapter Reset Failed Msgid 0210 Debug Adapter Transition Memory Management Events Service Level Interface SLI Events Msgid 0452 Debug Iocb Error Msgid 0432 Debug Ring ResetMsgid 0450 Error Iocb Invalid Msgid 0440 Debug Adapter Msg Mailbox Events Node Events Msgid 0610 Debug Node Destroy Msgid 0603 Debug Node UpdatedMsgid 0602 Notice Node Create Failed Msgid 0611 Debug Node Closed Link Events ELS Events General I/O Packet Events Msgid 0911 Debug TXQ Watchdog Msgid 0922 Notice Packet Flush TimeoutMsgid 0931 Error Packet Transport Error Msgid 0920 Debug Packet Flush FCP Traffic Events IP Traffic Events Solaris SFS Events Msgid 1312 Warning Echo Diagnostic Failed Msgid 1310 Warning Diagnostic ErrorMsgid 1311 Debug Echo Diagnostic Completed Msgid 1313 Debug BIU Diagnostic Completed Ioctl Events Firmware Download Events Common Transport Events Msgid 1622 Debug CT reply Msgid 1630 Error Invalid CT command foundMsgid 1621 Debug Unsolicited CT dropped Use Cases Different use cases will drive different migration scenarios Startemlxsmigration.sh Operational Differences Between lpfc and SFSSample Script File Details Finishemlxsmigration.sh Things to Know Before You Migrate Migrating a Configuration without FC BootMigrating Automatically Limitations Migrating Manually Migrating a Configuration with FC Boot Migrating Non-emlxs HBAs to emlxs HBAs For an Emulex boot HBA Shut down the server and get to the ok prompt