Extron electronic IPI 100 Series, IPI 200 Series - page 20

IPI 100 AAP, IPI 200 AAP Series • Installation

Installation, cont’d

2-6

IPI Rear Panel Features and Cabling

Ä Intercom port (IPI 101 AAP and IPI 104 AAP only) — This port

is used for power, control, and voice data communication with

the MLC. Plug one end of a standard, straight through, CAT 5,

CAT 5e, or CAT 6 cable terminated with RJ-45 connectors into

this port. Plug the other end of the cable into the Intercom

connector on the MLC 226 IP’s rear panel, as shown in the

following gure.

N A 12” (30.5 cm) CAT 6 cable is included with each IPI. If

you choose to terminate your own cable, the cable must be

no longer than 100’ (30.4 m).

Cables must be terminated to the T586A or T586B

standard and both ends of a cable must be wired to the

same standard.

HOST

CONTROL

R

1=DIGITAL I/O

2=Tx 3=Rx 5=GND

38400, N, 8, 1

PRESS TAB WITH

TWEEKER TO REMOVE

INTERCOM

AUDIO

OUT

LAN

IPI 101 AAP or IPI 104 AAP

Rear PanelMLC 226 IP Rear Panel

<100’ (30.4 m)

POWER RELAY

CNO

AUDIO OUT

LAN

Power

Contact

Relay

Audio Out

IPI 104 AAP, IPI 101 AAP

Rear Panel

AAP Mounting Screws (4)

Intercom Port

1a

2

IPI 204 AAP, IPI 201 AAP

Rear Panel

LAN Port

1b

AAP Mounting Screws (4)

2

3

4

5

Contents

Main Users Manual MediaLink IP Intercom Interfaces 68-1170-01 Rev. C 12 08 IPI 100 Series IPI 200 Series PUSH TO TALK PUSH TO TALK 1234 PUSH TO TALK PUSH TO TALK 1234 Precautions Instrucciones de seguridad Espaol Caution Warning Attention FCC Class A Notice Page IPI 100 Series, IPI 200 Series Quick Start Guide QS-1 Quick Start Guide IPI 101, IPI 104 W Step 1 Step 2 Step 3 Quick Start Guide IPI 101, IPI 104, contd Quick Start Guide IPI 201, IPI 204 Page Table of Contents Chapter One Introduction Chapter Two Installation Chapter Three Operation Chapter Four Conguration and Control Table of Contents, contd Chapter Five IPI 201 and IPI 204 Series SIS Programming and Control Appendix A Specications, Part Numbers, and Accessories Chapter One Introduction Introduction 1-2 About this Manual N Terms used in this manual N Introduction, contd 1-4 Features System Requirements Chapter Two Installation Installation 2-2 W N UL Requirements Mounting the IPI 101 or IPI 104 into an AAP Wall Plate or Device Faceplate 2-5 Mounting the IPI 201 or IPI 204 into an AAP Wall Plate or Device Faceplate IPI 100 AAP, IPI 200 AAP Series Installation 2-6 e MLC Audio Connection N Sample Applications Single PC-to-panel mode Multiple PC-to-panel mode (per help desk PC) to a network using straight-through cable. TCP/IP Network Classroom IP 10.XX.XX.02 MLC 226 IP AAP IPI 101 AAP Installation, 2-10 ON OFF AUTO MLC 226 IP AAP IPI 101 AAP Card MIS Panel-to-panel mode N 2-12 Intercom with amplier mode MLC 226 IP TCP/IP Network Configuration Console PC IP 10.XX.XX.01 Classroom IP 10.XX.XX.02 2-13 SI 26W BASSLEVEL TREBLE MINI POWER AMPLIFIER LAN R Page Page IPI 100 Series, IPI 200 Series Operation Operation 3-2 Front Panel Features and Operation a b c d IPI 100 Series, IPI 200 Series Operation e N f Button Operation Push to talk operation Operation, contd 3-4 Indication (lighting) Button Color Indication Chapter Four Conguration and Control Conguration and Control 4-2 N Software System Requirements Installing the Software 4-3 Using the Software: an Overview N 4-4 IP Intercom HelpDesk screen before conguration Page 4-6 a b Making a group announcement Speaking to an intercom N N 4-8 c Listening to an intercom N 4-9 Hands-free operation d e f 4-10 g 4-11 h 4-12 i Main Screen Menus File menu Tools menu Intercom menu N Help menu 4-14 Setting preferences a 4-15 b c N 4-16 d e Conguring the IPI Intercom System N 4-17 a 4-18 b c N d 4-19 4-20 Setup procedure 4-21 4-22 N 4-23 Recording an original message 4-24 N Changing the audio format of existing les 4-25 Page Chapter Five IPI 100 Series, IPI 200 Series SIS Programming and Control IPI 201/204 SIS Programming and Control 5-2 N Host-to-IPI Communications IPI-initiated Messages Password information Error responses 5-4 Error response references ASCII to Hex conversion table Commands and Reponses Using the command/response tables . 5-5 N With Telnet you can use either an Escape ( E Symbol denitions Page Page Page 5-10 Additional Firmware version, part number & information requests Status commands 5-11 Additional 5-12 Additional Page Page 5-15 Additional E X1@ CN } W X1@ X4( E IP setup commands Page Page Page 5-19 Additional E X2@ CV}W X2@ CV|Vrb X2@ ]Enable or disable the verbose X2@ 5-20 Additional E CV }WCV| X2@ ] X1$ E EB }W EB| X6$,X1$ ] E E X6$ EB }W X6$ EB|Bmd Page Page Page 5-24 Additional E {port#}MT }W{port#}MT|Pmt {port#} ]Select a number for the port E 0MT }W0MT|Pmt 00000 ] Setting the port number to 0 E MH }WMH|{port#} ] E 80MH }W80MH|Pmh 00080 ] This resets the Web port to E 23MT }W23MT|Pmt 00023 ] This resets the Telnet port to E {port#}MD }W{port#}MD|Pmd {port#} ] E 2001MD }W2001MD|Pmd 02001 ] This resets the direct access E path/directory/ CJ }The directorys name must be E 0MD }W0MD|Pmd 00000 ] E MD }WMD|{port#} ] Page Page 5-28 Additional Stream Files via Port 80 File handling commands E lename EF}W lename EF|Del lename ] E//EF}W %2F %2F EF|Ddl] E/EF}W %2F EF|Ddl] Page Page Page Page Page Specications, Part Numbers, Accessories Specications, Accessories A-2 Specications IPI 101, IPI 104 Series Audio IPI 101, IPI 104, and MLC 226 IP Audio input IPI General N All nominal levels are at 10%. N Specications are subject to change without notice. Specications, Accessories A-4 Specications IPI 201 and IPI 204 Series Audio Audio input N 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu Audio output Control relay General Specications, Accessories A-6 N All nominal levels are at 10%. N Specications are subject to change without notice. Included Parts (IPI 101 AAP and IPI 104 AAP) Accessories Included Parts (IPI 201 and IPI 204 Series) Accessories Extrons Warranty 2008 Extron Electronics. All rights reserved.