Port Assignment of the LAN Switch Blades | Fujitsu BX600 S3 instruction

Ethernet I/O Blades

Port Assignment

8.9Port Assignment of the LAN Switch Blades

For each of the ten server blade slots, connections to a maximum of 6 ports of the onboard LAN controller and to 2 ports of the optional Gigabit Ethernet daughter card are available in the BX600 S3 basic unit. With 4-way

server blades, the number of connections increases accordingly.

The LAN I/O blade in the NET1 slot is connected to port A of the onboard LAN controller of the installed server blades. The LAN I/O blade in slot NET2 is connected to port B of the onboard LAN controller. In the same way, the LAN I/O blades in slots NET3 and NET4 are connected to port A and B of the gigabit Ethernet daughter cards.

NET2

NET4

NET1

NET3

Figure 40: Slots for the LAN I/O blades

The installation of two LAN I/O blade in NET1 and NET2 (or NET3 and NET4) enables redundant LAN connections to be provided for the relevant LAN con- trollers of the server blades.

VCAUTION

●LAN switch blades must always be installed in slots NET1 and NET3 first. This ensures that port A of the relevant LAN controller is connected if redundant LAN connections are not used.

●To provide fibre channel functionality, fibre channel I/O blades must be installed in slot NET3 and/or slot NET4, see page 101.

Asynchronous balanced mode of Ethernet I/O blades and fibre channel I/O blades in slots NET3 and NET4 is not permitted.

BX600 S3

Operating Manual

91

Image 91

Fujitsu BX600 S3 manual Port Assignment of the LAN Switch Blades, NET2 NET4 NET1 NET3

Contents

Primergy BX600 S3 Basic Unit Copyright and Trademarks Comments… Suggestions… Corrections…Certified documentation according to DIN EN ISO Contents Contents Fibre Channel I/O Blades Replacing a Fan in the Unit Primergy BX600 S3 Basic Unit Preface Additional Server Documentation Overview of the DocumentationOverview of the Documentation Preface Concept and Target Group of this Manual Further Sources of Information Communication Interfaces FeaturesFeatures Preface Server Capacity Features KVM Blade Management Blade Server Management Power SupplyVentilation High Level of Availability and Failure Protection Service and Support ServerView Installation Manager Notational Conventions Electrical Data basic unit without server blades Technical DataTechnical DataPreface Electrical Data single power supply unit Environmental Conditions WeightCertification Mechanical Values Noise Level Technical Data Overview Installation Steps Overview Installation Steps Important Notes Before Setting Up Important Notes Batteries Other Important Notes Components With Electrostatic-Sensitive Devices FCC Class a Compliance Statement CE CertificateCE Certificate Transporting the Basic Unit Important Notes Environmentally Friendly Product Design and Development Environmental Protection Environmental Protection Symbols for electrical electronic devices Local Contacts Returning BatteriesPage Installation Steps Installing the HardwareInstalling the Hardware Unpacking the Basic Unit Unpacking the Basic Unit Requirements of the Rack Installing the System in the RackPRIMECENTER/DataCenter Rack 3rd-Party Rack Installing the System in the Rack Mechanical conditions BX600 S3 Mounting the support brackets Mounting the Assembly Kit Mounting the left carrier rail Mounting the basic unit Mounting/Removing the Basic Unit Connecting External Devices Connectors on the back of the basic unit Connecting External Devices PCI Cards with Cable at the Front Cable Routing Installing the Hardware Connecting Cables Instructions on Connecting and Disconnecting CablesDisconnecting Cables Connecting the System to the Mains Connecting the System to the Mains Connecting the System to the Mains Page Preparation for Use and Operation System power ON/OFF button Operating and Indicator Elements of the Basic UnitOperating and Indicator Elements Power indicator bicolor LED Preparation for Use and Operation Front identify/Fault indicator amber LEDFront identify button Rear Rear identify/Fault indicator green LED1Rear identify button1 Switching on the Basic Unit Basic Unit is Powered OFF Switching the Basic Unit ON/OFFSwitching OFF the Basic Unit System is Powered on Specified switch-ON time/switch-OFF time Switching the Blade Server ON/OFFAfter power failure Switching the Server Blades ON/OFF Cabling the System Management Blade ConfigurationPre-Configuration Requirements Initial Configuration via Serial Connection to Client Vcaution Management Blade Configuration Enter 1 to call up the Management Agent Information menu Management Agent Information menu Agent NIC Duplex Mode menu Updating System Components Updating the Server Blade Firmware Bios and BMCProceed as follows Updating the server blade Bios via the web interface Updating the server blade BMC via the web interface Updating the Management Blade Firmware Updating the management blade firmware via the web interface Updating the Switch Blade Firmware ⎜ Press Ctrl-Q Return Console Menu Removing an operation code image file Click Transfer from Server Page Preventing Unauthorized Boot Process Bios Setup Security FunctionsPreventing Unauthorized Bios Setup Calls Preventing Unauthorized System AccessPage Primergy BX620 S3/S4 2-way server blade BX600 S3 Server Blades Primergy BX630 scalable server blade 4-way configuration Server Blades Fitting rules Adding a Server Blade to the System Server Blades Adding a Server Blade to the Basic UnitRemoving the Dummy Module Adding a Server Blade to the System BX600 S3 Inserting the server blade Final engaging of the locking mechanism Removing the Server Blade Ethernet LAN I/O Blades Ethernet Switch Blade SB9 6x1Gbit Gbit Ethernet LAN Switch Blade SB9 6x1Gbit Ethernet I/O Blades GbE Intelligent Blade Panel IBP 10/6 Ethernet Switch Blade SB9 6x1 Gbit + 2x10 Gbit Gbit Ethernet LAN Switch Blade SB9 6x1 Gbit + 2x10 Gbit Ethernet I/O Blades Ethernet Switch Blade SB9F 12x1 Gbit Gbit Ethernet LAN Switch Blade SB9F 12x1 Gbit GbE Intelligent Blade Panel IBP 30/12 Ethernet Switch Blade SB9F 12x1 Gbit Cisco Catalyst Blade Switch Cisco Catalyst Blade Switch Cisco Catalyst Blade Switch Gbit Switch Blade 10/2 10 Gbit Switch Blade 10/2 Gbit Switch Blade 10/2 Ethernet LAN Pass-Thru-Blade NET2 NET4 NET1 NET3 Port Assignment of the LAN Switch Blades LAN port assignment with ten 2-way server blades Port Assignment BX620 S4 LAN port assignment with five 4-way server blades Configuration with Five 4-way Server Blades Way Blade Server Way server Installing an I/O Blade Installing an I/O Blade Remove the dummy module from the slot Disengaging the I/O blade Inserting the I/O Blade Inserting the I/O blade a = green touch point Removing the I/O BladePage Fibre Channel I/O Blades Gbit FC Switch Blade SW4016 4D 4/4 Gbit Fibre Channel Switch Blade Brocade SilkWorm 4016 4D FC switch blade status display 2-color LED IThe LED might also blink while testing Gbit FC Switch Blade SW4016 2/4 Gbit Fibre Channel Switch Blade Brocade SilkWorm Fibre Channel I/O Blades 2 Gbit Fibre Channel Pass-Thru Blade Gbit FC Pass-Thru Blade 4 Gbit Fibre Channel Pass-Thru Blade Inserting a Fibre Channel SFP module Fibre Channel SFP Module Removing an SFP Module Fibre Channel SFP Module NET4 NET3 Port Assignment Fabric port assignment with 2-way server blades Configuration with Ten 2-way Server Blades Operating Manual 111 FC I/O blade installation FC I/O Blade Installation Management blade slots Management Blade LAN link indicator green LED Lights green The LAN is linked Serial port connectorControl and Connection Panel Master indicator green LED LAN active indicator amber LEDI2C connector Failure indicator amber LED Exchanging a Management Blade Exchanging a Management BladeRemoving the Management Blade Operating Manual 117 Removing the management blade KVM Blade Standard Version KVM Blade Control Panel of the KVM Blade Standard Version ID/error LED green LEDKVM connector KVM Blade Standard Version Control Panel of the Adv. KVM Blade 11.2 Adv. KVM Blade Adv. KVM Blade Rear ID/error LED green LEDLAN activity indicator green LED LAN connection indicator orange LED Digital KVM Blade Control panel of the digital KVM blade Power indicatorID indicator Digital KVM Blade PSU4 PSU3 PSU2 PSU1 Power Supply Concept Basic unit with a single phase input Single basic unit with a single phase input Single basic unit with a 3-phase input Power Supply Concept Single basic unit with a 3-phase input UPS Single basic unit with a single UPS Single basic unit with two UPSs Power Supply Concept Single basic unit with two UPSs Two basic units with two UPSs Single-phase or Phase input Power Supply Concept Power Supply Units On/off display green LED Power Supply UnitsFault display amber LED Mains power supply display green LED Replacing a Power Supply Unit Disengaging the power supply unit a = green touch point Operating Manual 135 Removing the PSU Adding a Power Supply Unit Operating Manual 137 Page FAN1 FAN2 Ventilation Concept Fan Unit Fan UnitFan 1 LEDs Fan 2 LEDs Fan condition Ventilation Concept Replacing the Fan Unit Removing the fan unit Replacing a Fan in the Unit Page Power supply overloaded Troubleshooting and TipsSystem Power LED Remains Unlit Wrongly connected power cables Switch blade fails Front or Rear Identify/Fault LED Blinks AmberTroubleshooting and Tips One of the power supply units fails Screen Remains Dark System Switches Itself OFF Monitor does not support the set horizontal frequency Flickering Stripes on the Monitor ScreenNo Screen Display or Display Drifts No Mouse Pointer Displayed On the Screen Defective Drive Server Blade Does Not BootFloppy Disk Cannot Be Read/Written Time and Date Are Not Correct BX600 S3 Abbreviations Abbreviations ISCSI Post USV Page Primecenter Rack Related Publications 158 Operating Manual Operating Manual 159 Page EMC Index LED Index LAN Unpacking