Case of IPv4 multicast use | Hitachi GR2000 instruction

		Routing				Min. band
	MPLS protocol	processor	IPv4 unicast	IPv4 multicast	ATM VC count	guarantee with
	mode	module (RP)	path entry count	path entry count	per NIF	kbit/s
		memory				designated

	LDP (DU) Mode	64MB or more	2,000 or less	unused	256 or less	no

		128MB	125,000 or less	unused	2,048 or less	yes

	LDP (DoD)/	64MB or more	2,000 or less	unused	256 or less	no
	CR-LDP Mode
	CR-LDP Mode	128MB	90,000 or less	unused	2,048 or less	yes
		128MB	90,000 or less	unused	2,048 or less	yes

			(Note 1) (Note 4)		(Note 2)	(Note 2) (Note 3)

*1 It is necessary to increase the memory of all RPs installed in the device.

*2 It is necessary to increase memory so that the minimum required memory is provided only for the relevant RPs (the memory required for each RP differs).

*3 Min. band guarantee with kbit/s designated is a QoS queue attribute of configuration definition data in WAN (6Mbit/ s or less, excluding ISDN) and is a mode that is designated by the bandwidth_kbps parameter.

*4 Remote-gateway path entry required for MPLS operation is included in the path entry count.

In the case of IPv4 multicast use

With regard to the number of route entries for IP unicast, number of route entries for

Image 236

Hitachi GR2000 manual Case of IPv4 multicast use

Contents

Hitachi Gigabit Router GR2000 Series GR2K-GA-1002 Rev GR2000 Installation Guide Rev Release 4.00 May Change RecordPreface GR2K-GA-1002 Acknowledgments GateD Bsdi Internet Server GR2K-GA-1002 Rev AT&T David M. GAY INFO-ZIP Group Vii SUN MICROSYSTEMS, INC Viii Washington University in Saint Louis Martin Birgmeier Frank VAN DER Linden Diff, grep Xii Less TcpdTcpdump Xiii Traceroute Xiv Zlib Apache Http server Xntp Program MD5 ProgramPimdd Xvi Mrouted PIM sparse-mode pimd Xviii Ltcs Label Traffic Control System Kame IPv6 Stack Abbreviations DDP Xxii GR2K-GA-1002 Rev NIF Xxiv GR2K-GA-1002 Rev UNI Xxvi General Safety Guidelines Damage to the equipment or a disruption in service Specific Warning Instructions Xxviii To avoid damage to the equipment or a disruption in service Specific Caution Instructions Cleaning Other InstructionsStorage Xxx Table of Contents RM-CPU2S RMB-IOHRouting Processor RP Network Interface Module NIF Xxxiii Power Supply Unit POWCustomer-Responsibility Interface Cables Configuration Limits Xxxiv GR2K-GA-1002Prerequisites MPLS/IP-VPN ROUTE-OS3 Segmentation/Topology Restrictions LAN Networking RestrictionsWAN Networking Restrictions ATM Networking Restrictions Xxxvi Precautions on IP Connection with Other DevicesPrecautions on IPX Connection Precautions on Bridge Connections Precautions on QoS ControlPrecautions for using IP multicast Precautions for using Mpls Power and Cooling Requirements Xxxviii GR2K-GA-1002 RevEnvironmental Requirements Layout Mounting and Unmounting of Flash Memory Card MC Handling of Gbic Connection of Setup ConsoleRouting and Connection of Cables Starting, Setting Up, and Stopping Fans Expansion of Gbic Removal of Gbic Introduction Supplied Media and Equipment Required Xlii Outline of Installation GR2K-GA-1002 Xliii Rev RM-CPUMHRMB-CPU MH or RM-CPULHRMB-CPU LH Front Panel View Xliv 100 101102 GR2K-GA-1002 Xlv Rev Hardware Installation Xlvi GR2K-GA-1002 Xlvii Rev Sequence of Device Operation Unmounting of MC Connection of Setup ConsoleXlviii GR2K-GA-1002 Xlix Rev Specifications of Interface Cables and ConnectorsNE1G-1LHBA switch and function of LED indications LED indications Operation terminal conditions Modem setting RP mounting conditions by each modelThis case core/clad diameter is 62.5/125 µm Lii Methods for Router Restart Liii Liv Chapter General Information Purpose and Organization of This Manual Outline of Installation Process Outline of Installation GR2K-GA-1002 Rev Chapter Product Overview Models Physical Appearance Front view of GR2000-2S AC input Product Overview Front View of GR2000-4S AC InputFAN3 RMP NIF1 NIF0 FAN2 Rear View of GR2000-4S AC Input RM-CPU POW1 POW0 Rear View of GR2000-6H AC Input POW1 POW0 Rear View of GR2000-10H with AC Input Front View of GR2000-10H with DC Input 10 Rear View of GR2000-10H with DC Input GR2K-GA-1002 Rev 11 Front View of GR2000-20H with AC Input GR2K-GA-1002 Rev 12 Rear View of GR2000-20H with AC Input GR2K-GA-1002 Rev RP RP RP RP RP RM- RM- RP RP RP RP RP GR2000-20H with DC Input 13 Front View 14 Rear View of GR2000-20H with DC Input GR2K-GA-1002 Rev 15 Front View of GR2000-4 AC Input 16 Rear View of GR2000-4 AC Input GR2K-GA-1002 Rev 17 Front View of GR2000-10 with AC Input 18 Rear View of GR2000-10 with AC Input GR2K-GA-1002 Rev 19 Front View of GR2000-10 with DC Input CSW-1S CSW-1M CSW-0S CSW-0M IO0 IO1 Placement of power supply units 23 Front View of GR2000-20 with DC Input GR2K-GA-1002 Rev 24 Rear View of GR2000-20 with DC Input GR2K-GA-1002 Rev Guide rail attached Guide rail detached Device Configuration BCU RMP RM + RP NIFPOW ATM WAN LAN BCU POW GR2000 Installation Guide GR2000-2S RMP NIF1 NIF0 31 Front View of GR2000-4S 33 Front View of GR2000-6H 35 Front View of GR2000-10H with AC Input IO0 GR2000 Installation Guide GR2000-20H 37 Front View of GR2000-20H with AC Input GR2K-GA-1002 Rev 38 Rear View of GR2000-20H with AC Input GR2K-GA-1002 Rev Device Components Maximum Number of Device Components on Enhanced ModelsBCU-H850H BCU-M850H BCU-L850H Cabinet Network Processor Unit Chassis Basic Control Unit BCUBCU RM NIF BCU RM RM-CPU RM-IORMB-CPU RMB-IO Crossbar Switch CSW Routing Processor ModuleRP GR2000 Installation Guide RP Specifications RP name SpecificationRP-A1 RP-DV RP-CV RP-D6RP-C6 Type Module Name Interface Size Network Interface Module NIFList of NIF Modules Product Overview List of NIF Modules Power Supply Unit POW CPU FanMain Storage Card MS Flash Memory Card MC NIF accessory Gbic Temperature monitoring sensorGBIC-SX/LX/LH Physical Specifications Purchasing overseas Interface Cables Threshold value Temperature Significance Name Value Software NIF Connections Interface Cables and Connectors10 Specifications of Interface Cables and Connectors NWMX1-4 BNCNWE3-1C POS MMF NWOC3C-2MD Atmsmf 1.1 LANAtmmmf 1.2 WAN LAN Connection Network Connections1.3 ATM WAN Connection ATM Connection This page left intentionally blank Installed Dimensions, Masses, and Minimum Service Clearances Cabinet Chassis Minimum Service Clearance for Desktop or Floor Installation Module Characteristics Component Details BCU Components Basic Control Unit BCURM-CPU2S RMP 2S RMP Front Panel View GR2K-GA-1002 Rev Power ErrorAlarm Accesso Pin No Specifications Line ERRLamp Test Rest RM-CPU4S, RMB-CPU 4S Front Panel View Active Specifications of 9-pin D-sub Connector on AUX RS232C PortStatus RM-CPUS, RM-CPUM, RM-CPUMC2 and RM-CPUL 10 RM-CPUS Front Panel View RM-IO4S, RMB-IO 4S and RM-IOH 12 RM-IO4S Front Panel View EMA Suppress Reset LINK/ACTEMA Supress RM Change Pin No. Specifications RM-IOS, RM-IOM, and RM-IOL CSW Status RMB-IOH8 CSW 12 RP Models Routing Processor RPRP-A1/RP-D/RP-D6 21 RP-C/C6 Front Panel View Switch and LED indication RP-C/RP-C6 Category Physical Interface NIF Name Board Size Remarks Network Interface Module NIF15 NIF Models Pin No 1 NE100-8T, NE100-8TA and NE100-8TBComponent Details 15 NIF Models Link Connector Specifications2 NE100-4F, NE100-4FS, and NE100-4FS4 Name Name of switch Status Content LED LineACT SIG-DT NE1G-1LB NE1G-1LHA Name LED Color Status ContentNWVX-4 NWVX-4 Line LED indication WAN 15-pin Male Connection Router 50-Pin Specifications WAN 35-pin Male Connection Router 50-Pin Specifications NWVX-8 ACT, T/R Precautions when connecting NWVX-8 Line stateIndication Line state Detail of state State as seen by Sxmp MMI Line 5 Line 4 .+0#%6.+064 4 LINE8 1 8 Line 0 .+0 28 Line numbers for the cables attached to NWVX-8 DCE side GR2000 Cables attached to 28Connector Specifications for NWVX-8, Pin Assignment for 30Connector Specifications for NWVX-8, Pin Assignment for Status Actg Line Erry T/R Yellow Blocking and the board replaceable state Line ERR ACT NWJ1-8U physically appear as Figure Status Link T/R Loop LOS RAI Line Browser Status Loop Link T/R LOS RAI Line Line LOS RAI ACT LOS AIS Line NWJ2-1U Browse State as seen by Line stateLine state Detail of state Indication in M TR T Line ERR Looped by rem Line ERR Loop R ACT LOS RAI NWE3-2U Line LOS RAI Name LED Color LED Green Line RAI LOS Status MST Line ERR ACT Link POS OC-3C/STM-1 Function of LED indication NWOC3C-8S and NWOC3C-8M physically appear as Figure Shows the operating Green Operable operation MST Line ERR ACT Link Line 0A NWOC12-4S and NWOC12-4M physically appear as Figure 46 NWOC48-1S, NWOC48-1S4 and NWOC48-1S8 Front Panel View NWOC48-1A, NWOC48-1A4 and NWOC48-1A8 APS IndicationStatus Green Yellow Extinguished 48 NAOC3-1M and NAOC3-1S Front Panel View Green blinking Under preparation Program being NAOC3-8S and NAOC3-8M physically appear as Figure LED Green Shows the operating NAOC12-2S and NAOC12-2M physically appear as Figure NE1G-4C physically appears as Figure NWT3-1C physically appears as Figure Line state Detail of state Indication in MMI NWE1-8 physically appears as Figure ACT 87 POW Models POW-S100SPOW-H100H POW-M100H Device Model Power Supply Configuration ’ty POW-MDCINPUT-MDC POW-LDC 56 Power Unit of POW-H100H POW-HDCH LED LED 173 175 LED SW1 63 Power Unit of POW-S100 POW-M100 and POW-L200 520 Fittings 67 MC30 and MC64 Flash Memory Card Module 69 WAN Loop Connector 3 V.24, V.35, and X.21 Interface CablesPage NWVX-4 NWVX-8 Pin high-density connect 74 Line numbers for the cables attached to NWVX-8 DCE side GR2000 Cables attached to 1m or shorter Coordinated individually NWVX-8 Page Router LAN setup boundary with network Transmit + Receive + Unused Core SC Core SC Boundary with network POS DSU UTPPOS SMF DSU Carrier e.g., NTT facility Customer facility UTP Cable for Primary I.431 or I.431-a 89 Connection to Device without Terminator 91 Sample Indirect Connection with Primary I.431 or I.431-a Outer Metal Coaxial Cable for Secondary G.703 Pin No Function device side Function DSU side Multimode Optical Fiber Cable for OC-3c/STM-1 POS MMF 95 Construction of duel shield type coaxial cable Connector Attenuation 1 dB/km max km Connector Attenuation 0.3 dB/km max km or 40 km Page DSU/ONU NAOC3-1M Below For connection to box 103 UTP Cable Specifications for 25Mbps ATM Local Setup Console and Remote Operation Terminal Prerequisites Operation terminal conditions Terminal type Connection patter Required function GND DCDCTS RTS AT&Y0 AT&W0Page Page Model RP GR2000-2S GR2000-4S GR2000-6H GR2000-10H GR2000-20 1 RPRP mounting conditions by each model Whole RP Applicable Types and Quantities of RPs by Router ModelModel Mounting number Inter Board Quantities of NIFs by Router Model10H NAOC12-2M NAOC12-2SNAOC3-8M NAOC3-8S Add One MS64 Add One MS1 RP Memory Increment by RP TypeResulting Memory Capacity MB Line Accommodation with WAN Other than Isdn and Overload 11 100BASE-FX Line Accommodation6Mbit/s or less WAN circuit accommodation conditions Router Model Max. No. of Lines Per NIF Per RP Per Router Condition Max. Throughput kbps per Max. Throughput kbps per RP Line Accommodation with WAN Overload17 WAN Isdn Line Accommodation Limit Condition QoS 384 128 920 860 750 NIF Condition Max. Aggregate Line Speed Mbps Example a Vlan Note Bridge Non-VLAN IP multicast IPv Vrrp Mpls Vlan Line accommodating conditions for ATMPer router Per RP Per line Maximum Number of ARP Entries 31 Maximum Number of ARP EntriesRouter Model Maximum No. of ARP Entries Per RP Per Router Router Model Maximum Number of VCs Per Line Per NIF Maximum Number of Interfaces and Multihome SubnetsMaximum Number of Interfaces Maximum Number of Neighbor Routers 36 Maximum Number of Neighbor Routers Memory Entries Multipath Not Used Multipath Used BGP4 40 IP Multicast Accommodation Limits Max. Limit 41 IPX Accommodation Limits 42 Bridge Accommodation Limits 44 Maximum Number of Dynamic and Static Entries Maximum Limit Total Dynamic Static Parameter setting IP-VPN system Category NIF Name Mpls Support *1 Backbone circuit NE1G-1LA NE1G-1SA NE1G-1LHA NE1G-1LHA8NE1G-1LB NE1G-1SB NE1G-1LHBA NE1G-4C WAN NWVX-4 NWVX-8 NWJB-8 NWJ1-4U NWJ1-8U NAOC3-8M NAOC3-8S Memory Card Unit MCMinimum Memory Requirements RIP+OSPF BGP4 Note Case of IPv4 multicast use IP unicast IP muiticast Maximum path entry countMaximum number of entries By protocols No. Maximum number of entries ATM VCs By protocolsEntry Count Static Count Routing IP multicast path entry count Processor IP unicastModule Path entry Count per Entry Guara Count Entry count Mpls protocol Function item Detailed item Support Mode LDP DU VPN ID Dynamic Entry and Static Entry Maximum Entry Count 55 Maximum entry number of Mpls policyMaximum RP entry number Maximum device entry number 000/RP 10,000/device 57 Cops agent accommodating conditions Memory size of 256 MB or greater RP-CRP-D 61 BCU minimum required memory BCU Number of NDP Entries 64 Number of interfaces Maximum Number of IPv6 Addresses to be Set Number of Tunnel Interfaces Address BGP4+ ARP Tag-VLANRouting Processor Module RP and NIF Number of Tag-VLANs to be Set in Multi-Home Router Model Number of Tag-VLAN Per RP Per Router 76 Cops agent accommodating conditions Network Configuration Items to be Prepared 3 1000BASE-SX/1000BASE-LX/1000BASE-LH 1 10BASE-T/100BASE-TX2 100BASE-FX WAN Networking Restrictions Packet Length Protocol operation Terminal DTE Device is Condition Alternative NTT Sync clock -clock Isdn 80 NWJ1-8U connection restrictionsLine Interface Time slots start Posible Time Number Slots Cellularization Overhead Bandwidth Planning ConsiderationsRouting Capacity of GR2000 on ATM Interface Own router Transmission traffic by each service category ATM Connection with Hitachi NP200 and NP220 ITU-T CBR LIFIlmi ATM Connection with Bridge Devices Function-wise Conditions for ATM ConnectionATM Connection with IPX Devices Interface Address in Point-to-Point Line Connection Page Router a Path to Ia is to be Learned by IG P Xterna l peer Page Connection with IPv6 Router Interface Address of Point-to-Point Type Line 13 Example for Specifying a nexthopself Parameter Device Packet to Terminal Terminal a Terminal B Page Functional item Detailed item Snmp Setting of SAP Packet Processing Configuration SettingsSetting of RIP Packet Processing Use of NetWare Serialization packet and diagnostic packetNetbios packet Model Traffic of Periodic SAP Packets Protocol and Topology Restrictions Spanning-Tree Protocol LAN1 Bridge Definition on Isdn Interface Relationship Between Load on RP and QoS RP, NIF Vlan type Connection with LAN SwitchTag-VLAN setting 21 Network Configuration Multicast relay Common to protocols 14.2.2 When using Dvmrp 14.2 Redundant route route switching due to impedimentWhen using PIM-DM PIM-DM Redundant route exists Inapplicable network pattern Tree type network Page Precautions for using Mpls VPN Contents of the TLV used Versions prior to VerPage Temperature and Humidity Environmental Requirements Dust Requirements Dust Computer Main Line Distribution Panel Acoustic Noise For the router Input Power Requirements Input Power Requirements-AC Input 100 Vac Single phase 50/60 Hz Ground Nema CB Circuit breaker Page Requirements for Circuit Breaker on Power Distribution Panel Router Model AC Input DC Input CB Type Phase Rating Receptacle Types for AC Input Page Typical Power Consumption and Heat Dissipation Figures Out lower rear end Out lower right side 12 Airflow of GR2000-4 Upper eft side Upper right side Cooling Requirements for Rack-Mount Installation Page Unpacking Chassis When you handle this model Packing list are obtained from the cargo Carton Router chassis Packing list are obtained from the cargo Vinyl bag Router chassis Carton Packing list are obtained from the cargo Packing list are obtained from the cargo RM/RP/NIF full size board Carton Polyethylene or vinyl bag Memory module Polyethylene or vinyl bag Carton Handling of Components Subject to Static Electricity 13 Unpacking of Separately Shipped Cable Allowable Style of Installation by Router Model GR2000-2S GR2000-4 Floor Installation of Chassis 17 Desktop Installation for GR2000-6HPage Page Screwjack/earthquake-proof bolt hole M12 Screw jack Caster Page Screwjack Page Stopper nut 10 mm Page Page Guide rail M5 screw x Screw Chassis Page 30600 RearFront Chassis AC Input Inch Rack GR2000-10H or GR2000-10 Guide Rail Removing Page Chassis Cable Power Interfa cable Guide rail Page 547.95 133.35 177.8 1430 Open rack Inch Rack GR2000-20H or GR2000-20 Guide Rail General Rules for Routing and Connection of Cables Page Page Page 2.1 GR2000-2S Rear Power Switch Tighten the screws Front Page 2.5 GR2000-20H 200V AC Input Front Page 53 Terminal Board/Wire Dimensions for DC Input to GR2000-20H 2.6 GR2000-4 Front Page Front Front Page 60 Terminal Board/Wire Dimensions for DC Input to GR2000-20 Connection of Interface Cables WAN V.24, V.35, RJ-48 to the mating receptacle on the own router Cause malfunction or a failure SC 2-core When removing, just pull Mating receptacle on the own router 70 illustrates how to unmount an MC How to remove BCU RM, duplexed Console specifications Starting, Setting Up, and Stoppin Overview of Device Operation Pause at least 2 seconds before you turn on the power Switch fully until it stops Password noneoperator Page Adding and Removing Component BCU, RP, and NIF ModulesPage Page Guide rail Anchor screw 1 GR2000-4S Below with both hands when installing or removing Below with both hands when installing or removing Input Unit AC or DC Follow the instructions illustrated in Figure Input Unit AC or DC Follow the instruction illustrated in Figure Power Switch POW for AC Input POW Dju st th e p ro je ctio n s POW Fan Tray for GR2000-10H Fan tray Cover RM-CPU Addition/Removal of Main Memory Module for RM BCU Installed connector Removingconfigmodeseta BCU duplexCR For termination of duplex mode Removing an RP FreerprpnoCR Network Interface NIFAdding an RP Page Software Installation and Update Introduction