Hitachi GR2000 manual Xxxvi, Precautions on IP Connection with Other Devices

GR2000 Installation Guide

	4.6.1.1		Routing Capacity of GR2000 on ATM Interface	4-58
	4.6.1.2		Cellularization Overhead	4-58
	4.6.1.3		Possible Loss of Link with Other Device Due to Shaping	4-59
	4.6.1.4 Outbound QoS on ATM Interface			4-60
	4.6.1.5 Relationship between Load on RP and QoS			4-60
	4.6.1.6		Setting of VP peak cell rate	4-60
	4.6.2	Required Settings for ATM Connection with Other Device		4-61
	4.6.2.1 ATM Connection with Hitachi NP200 and NP220			4-61
	4.6.2.2		ATM Connection with Hitachi AN1000	4-62
	4.6.2.3		ATM Connection with Cisco Systems’ Router	4-62
	4.6.3	Connection to ATM Services		4-63
	4.6.4	Function-wise Conditions for ATM Connection		4-63
	4.6.4.1		ATM Connection with IPX Devices	4-63
	4.6.4.2		ATM Connection with Bridge Devices	4-63
	4.6.4.3		Parallel PVC	4-63
4.7	Precautions on IP Connection with Other Devices			4-64
	4.7.1	Interface Address in Point-to-Point Line Connection		4-64
	4.7.2	Precautions When Using RIP-1 on Frame Relay or ATM Network		4-64
	4.7.3	Precautions When Using RIP-2 on Frame Relay or ATM Network		4-64
	4.7.4 Precautions When Using OSPF on Frame Relay or ATM Network			4-64
	4.7.5	Cautions When Using RIP-1 in Point-to-Point Circuits		4-65
	4.7.6	Cautions When Using OSPF on Point-to-Point Circuits		4-65
	4.7.7 Cautions When Using OSPF			4-65
	4.7.7.1		Cautions Regarding the HelloInterval Default Value	4-65
	4.7.7.2		Cautions Regarding the Priority Default Value	4-65
	4.7.8	Cautions When Using BGP-4		4-66
	4.7.8.1		Cautions Regarding NextHop Resolution	4-66
4.8 Precautions When Replacing Other Router with GR2000				4-67
4.9	Connection with IPv6 Router			4-68
	4.9.1	Connection with IPv6 Router		4-68
	4.9.1.1		Interface Address of Point-to-Point Type Line	4-68
	4.9.1.2		Caution on BGP4+ Connection Using Point-to-Point Type Line	4-68
	4.9.1.3 Caution When Changing the MTU Length of IPv6 Relay Line			4-69
	4.9.1.4		Hardware relaying function in the same link	4-69
	4.9.1.5		Destination IPv6 address of Ping6 and traceroute6 commands	4-71
	4.9.1.6		IPv6 function that can be used at IPv6 relaying software processing	4-71
4.10 Precautions on IPX Connection				4-73
	4.10.1	Configuration Settings		4-73
	4.10.1.1		Setting of RIP Packet Processing	4-73
	4.10.1.2		Setting of SAP Packet Processing	4-73
	4.10.1.3		Handling of Non-Data Packets	4-73
	4.10.1.4		Use of NetWare 4.1	4-74
	4.10.1.5		IPX Connection with ISDN	4-74
	4.10.1.6 Transmission Interval Settings for Dynamic RIP/SAP Packets on Pertinent Devices. 4-74
xxxvi				GR2K-GA-1002
				Rev. 6.03