Taking into service | Holder C 9.92 H specification

C 9.92	Operating Instructions

Taking into service

Daily checks and activities prior to taking into service

If damages or defects are found during the following checks, they must be eliminated before taking the tractor into serv- ice. Do not operate the tractor before proper repairs are car- ried out. Safety and protective devices should not be re- moved or disabled. Do not change fixed specified settings. Before starting work, make yourself truck familiar with all the functions and protective devices of the tractor.

Checking/cleaning the radiator and protection screens

NOTE

-Check that the protection screens (2 and 3) are clean.

-Clean the screens if necessary.

The screen (3) can be pulled off to the left after loosening the bayonet screw (4) and then easily cleaned.

-The air intake of the air filter (1) must be clean.

1

2

3

Bild_C992H_011

3

4		Bild_S 990_006
		Bild_S 990_006

153 146

45

Image 47

Holder C 9.92 H operating instructions Taking into service, Daily checks and activities prior to taking into service

Contents

OperatingInstructions Page Continual development General notes on serviceForeword For technical exigencies requiring particular attention ForewordSeptember Max Holder GmbH Max-Holder-Straße Metzingen Foreword Table of contentsPage Unintended use Information on the tractorIntended use Site of operation Disposal instructions Information on the tractorResidual hazards and risks Over 32 km/h Operating instructionsDriver’s licence Driver’s licence classes Operating instructions Operating instructions Previous drivers licence class Working clothes SafetyGeneral notes on safety Safety notes for retrofits Gear oil, engine oil, diesel fuel Safety instructions for handling fuel, fluids and lubricants Emissions Exhaust Gases Battery acidHydraulic oil, brake fluid Heat Battery Dimensional drawing Technical dataTractor dimensions Table of dimensions for S Technical data Distance between centreline of tires Technical data Weights Curb weight Max. loading Type 990 Engine specifications Theoretical ground speeds Fuel system Technical data /filling quantities Front lift Assembly Additional Description Information SteeringBrakes Tow coupling Traction hydraulics Assembly Additional information Description Rear liftDump body General tractor Electrical system Exhaust gas identification Noise level Front left view DescriptionViews of vehicle Rear right view DescriptionTractor Operating controls Driver’s station Controls on right front console Controls on right rear console Hand throttle Controls on rear console Pedals DescriptionJoystick Steering column adjustment Indicator lights Controls at front bottom of cabin Controls at front top of cabin Door controls Door opener Controls at rear of cabin Identification plates Location of plates and labels Mounting instructions for licence plate Overview of options and variants selection Assembly Additional information Dimension/order No./type Operating Instructions A11VO40EP Accessories Page Checking/cleaning the radiator and protection screens Taking into serviceDaily checks and activities prior to taking into service Checking the engine oil level Taking into serviceTurning on the battery isolating switch Battery can be switched off fully with the removable key Checking the tire inflation pressure Taking into serviceChecking the trailer coupling optional if necessary Checking the hydraulic oil level Filling fuel Checking the brake fluid level Adjusting the steering wheel Adjusting the backrest tilt Adjusting the driver’s seat with pneumatic suspen- sionDo not adjust the seat while driving. Risk of accident Adjusting the lumbar support Horizontal seat adjustment Adjusting the driver’s weightAdjusting the horizontal suspension Checking the lights and rear view mirror Topping up wiper water Before starting, make sure no-one is Do not start or run the engine in enclosedSpaces. Danger of poisoning through exhaust Gases Starting the engine BildC992H074 Checking the brakes and steering for proper function Page Before starting to drive Driving safety rulesOperation Driving with hydrostatic drive Tractor must be stationary for switchingOperation Driving Operation Stop Table of driving programs Position Marking Function Use Selecting road travel transport speed Setting the operating speed of programs 3 BildC992H024 Adjusting the fine adjustment knob Driving with SDS Special Drive System Changing the direction of travel Operating the inching pedal Table of ground speed ranges with Dual Drive Driving with hydrostatic Dual drive Drive the tractor warm for approx -12 min. at range Set the program switch to range Switching the differential lock off Switching the differential lock on Two-stage steering Steering Applying the parking brake Operating the service brakeBrakes Releasing the parking brake Driving on slopes Hydraulic oil for stationary operation Special operating instructionsStationary operation Park the tractor on level ground in both direc- tions 340 Nm Adjusting the track widthIdentical spacers must be installed on all four wheels Special operating instructions Special operating instructions Operation in winter Possible attachments Safety instructions for handling attach- mentsOperating the attachments Additional information for attachments Operating the attachments Front attachment Operating the attachmentsRear attachment or front/rear combinations Operating Instructions Installation of attachments Hole Position Used for Adjusting the catch hooksAdjusting the hitch insert length Both threads must be screwed in equally far Adjusting the upper link slide and upper link Coupling the hydraulic hoses Removing attachments Installing the articulated shafts Operating the joystick Joystick operation Lateral control of the front lift Operating the front liftFront lift tilt control Operating the front lift with the membrane keyboard Adjusting the tilt with membrane keyboard Switching the front lift to double-acting Lateral control with the membrane keyboard Transport safety External operation of the front lift Flow rate limiting for joystick Setting key for float position button Operating the rear lift External operation of the rear lift Operating the hydraulic couplings Operating the yellow and white hydraulic couplings Operating the green hydraulic couplingsOperating the blue hydraulic couplings Before turning the PTO on, make sure that PTO switch 1 must be switched offTurning on the front PTO Never turn the PTO on with the engine off Turning on the rear PTO Gas pressure in the diaphragm accu- mulator is 30 bar Adjusting control sensitivity hysteresisOperating the hydraulic accumulator* front lift Applications with hydraulic accumulator Switching the hydraulic accumulator off 105 Turn on the safety switch 6 only at low en- gine speed S990 Variable pump flow Switching off the attachment variable pump Increase the speed of the engine slowly Operating the hydraulic system* fixed setting 80 LTurn on the safety switch only at low engine speed Switching off the hydraulic system Operating the hydraulic dumping device Press button 4 only at low engine speed Operating priority flow valve Turning off the priority flow valve 113 114 Connecting line for priority flow valves 1 Page Removing the roof hatch Other operationsOperating the driver’s cabin Operating the roof hatch Opening the roof hatch Front windshield wiper/washer Other operationsOperating the windshield wiper/washer Other operations To flash the headlights, pull the turn signal lever up 120 Operating the horn Activating the left / right turn signalTurning on the top headlights Turning on the top strobe warning light Operating the 4-way hazard flashers Dome light Turning on the dome light Turning on the working lightsWorking light must not be used in public traffic Radio* and loudspeaker Operating the radio Power socket Connecting equipment to the power socket Heating and ventilating Turning on the heating Heater Ventilation fan has 2 speeds Turning on the ventilation Recirculating air operation Other operations Air conditioning Cleaning the condenserAir conditioning Operating the air conditioning Fuses for the tractor Fuses 130 Stopping the tractor Parking the tractorLeaving the tractor unattended Leaving the tractor unattended Parking the tractorParking Trailers, towing Operating the trailer coupling, attaching trailers Trailers, towing Driving with a trailer Page Do not step or stand under a suspended load. Danger to life Transport, hoisting, towingTransport instructions Hoisting instructions Towing instructions Transport, hoisting, towing Transport, hoisting, towing Page Indication of special operating conditions Indicators, adjustmentsAdjusting the speedometer Page Malfunction Cause Malfunctions, causes, remedyEngine and exhaust gas turbocharger mal- functions Traction electronics and traction hydraulics malfunctions Malfunction Cause Remedy Malfunctions, causes, remedy Malfunctions, causes, remedy 146 Hydraulic and steering system malfunctions 148 Working hydraulics malfunctions 150 151 152 How to value the tractor? General remarks on maintenanceQualification of service personnel Service Handling fuel, fluids and lubricants General remarks on maintenanceSafety notes for maintenance General remarks on maintenance Doing work on the electrical equipment Disconnect the battery ground lead Jacking up Jack lift points Securing the dumping subframe dump body Raise the cabin carefully Tilting the cabinPage See Maintenance scheduleMaintenance during the initial period of operation Interval Service and inspection Maintenance as required Maintenance scheduleRegular maintenance Periodic maintenance Maintenance every 1000 service hours Maintenance every 500 service hours Change the front and rear gearbox oil Maintenance every 5 years Interval Service and inspection Maintenance every 2 years Checking air tubes and air hoses for leaks Maintenance during the initial period of operationMaintenance after the first 50 service hours Checking the engine for leaks 168 Maintenance after the first 50 service hoursChecking the coolant level, topping up if necessary Checking engine V-belt tension and condi- tion Maintenance after the first 50 service hoursAdjust V-belt tension only when the engine is shut off Checking the heating hoses for damage and tightness 170 Checking the hydraulic lines and hoses for leaks and damageChecking the hydraulic oil level Replacing the working hydraulics pressure filter 172 Replacing the traction hydraulics pressure filter Changing the front gearbox oil including axle Change the gear oil only when at operating temperatureChanging the front and rear gearbox oil 174 Filling oil 175 176 Do not operate the tractor with a defective braking system Check the service brakeChecking the parking brake for proper op- eration 178 Tightening the wheel nutsTightening nuts and bolts according to the torque table Maintenance after the first 500 service hours Oil Maintenance after the first 500 service hours Replacement Maintenance after the first 500 service hoursCleaning Checking the engine valve clearances Approx LHydraulic system is vented automatically Maintenance as required Switch settings Combination Tire size Type Maintenance as required Checking the air cleaner system, cleaning if Necessary Maintenance as required 186 Replacing the hydraulic return filter for hydraulic system Cleaning with cold cleaner or water jet Checking the radiator, cleaning if necessaryCleaning with compressed air Cleaning the condenser 190 Greasing the tractor except universal joints Checking the frost protection of the windshield washer water Checking the air tubes and air hoses for leaks Maintenance every 250 service hoursChecking the engine oil level Checking the coolant, adding if necessary Maintenance every 250 service hours Maintenance every 250 service hours Checking the front and rear gearbox for leaks Checking the service brakeChecking the fuel lines for condition and tightness Checking the cable connections Checking the air conditioner for proper operation Checking the heating system for proper operation Visual inspection of air conditioner for leaks Checking the air conditioner hoses and wiring for damageChecking the seat of the compressor Checking the condensate water drain Checking the preheating system Lubricate the machine except universal joints Checking the tire inflation pressure Tighten the wheel nuts Checking the windscreen wiper, renewing if necessaryTightening nuts and bolts according to the torque table 10.5 L Maintenance every 500 service hoursChanging the engine oil at least once a year Oil Unscrew the oil drain plug Changing the engine oil filter Maintenance every 500 service hours Replacing the fuel filter element Maintenance every 1000 service hoursChecking the engine valve clearances Checking the glow plugs Lubricating the universal joints at least once a year Maintenance every 1000 service hours Changing the hydraulic oil at least every 2 years Maintenance every 1500 service hoursPage Replacing the injection nozzles Maintenance every 3000 service hoursThis work may only be carried out by your service centre Changing the toothed beltPage Changing the fresh air filter Annual maintenanceChanging the air filter element Changing the brake fluid Checking the battery, coating the terminals with grease Annual maintenance Lubricating the universal joints Page Changing the hydraulic oil or at 1500 hours Maintenance every 2 yearsChanging the coolant Replacing the V-belt Secure the annular fan screws with Loctite Maintenance every 2 yearsReplacing the air conditioner V-belt Changing the toothed belt or at 3000 hours Maintenance every 5 yearsPage Engine preservation Taking the tractor out of operation Removing the engine preservation Taking the tractor out of operation Coolant, fuel and lubricant specifications Page Filling quantities 990 Maintenance data Engine Torque Transmission, axles, wheels Maintenance data Designation Order number Maintenance dataList of replacement parts Bulbs 12 Use Power Rating Technical data of the engine 226 Alphabetical index Adjusting the driver’s seat with pneumatic suspension 210 Alphabetical index Index Alphabetical 230 231 232 233 234 235 236