NAS 200 User’s Reference | IBM 201 instruction

Table 18. Diagnostic error messages (continued)

Error Code	Meaning	FRU/action

217-XXX-000	Failed BIOS hard disk drive	Hard disk drive 1
	test
	Note: If RAID is configured,
	the hard disk drive number
	refers to the RAID logical
	array.

217-XXX-001	Failed BIOS hard disk drive	Hard disk drive 2
	test
	Note: If RAID is configured,
	the hard disk drive number
	refers to the RAID logical
	array.

217-XXX-002	Failed BIOS hard disk drive	Hard disk drive 3
	test.
	Note: If RAID is configured,
	the hard disk drive number
	refers to the RAID logical
	array

217-XXX-003	Failed BIOS hard disk drive	Hard disk drive 4
	test
	Note: If RAID is configured,
	the hard disk drive number
	refers to the RAID logical
	array.

217-XXX-004	Failed BIOS hard disk drive	Hard disk drive 5
	test
	Note: If RAID is configured,
	the hard disk drive number
	refers to the RAID logical
	array.

217-XXX-005	Failed BIOS Fixed Disk test	Hard disk drive 6
	Note: If RAID is configured,
	the hard disk drive number
	refers to the RAID logical
	array.

264-XXX-0NN	Failed tape-drive test	1. Tape cartridge, if user executed the read/write tape
		1. Tape cartridge, if user executed the read/write tape
		drive test (XXX = 256)
		2. SCSI or power cable connected to tape drive with SCSI ID
		NN.
		3. Tape drive with SCSI ID NN (Refer to the Help and
		Service Information appendix of the tape drive’s user
		guide).
		4. System board or SCSI Controller (Run SCSI controller
		diagnostic to determine if the SCSI bus is functioning
		correctly.)

264-XXX-999	Errors on multiple tape drives	See error messages/text in the PC Doctor error log for
		detailed information on each individual tape drive error.

301-XXX-000	Failed Keyboard test	Keyboard

405-XXX-000	Failed Ethernet test on	1. Verify that Ethernet is not disabled in BIOS
	controller on the system	1. Verify that Ethernet is not disabled in BIOS
	controller on the system	2. System board
	board	2. System board
	board

104NAS 200 User’s Reference

Image 116

IBM 201 manual NAS 200 User’s Reference

Contents

User’s Reference IBM TotalStorage Network Attached StorageModels 201 and Release First Edition November Contents Chapter 2. Configuration and administration toolsChapter 4. Storage configuration Chapter 5. Completing setup Chapter 6. Additional administrative functions Chapter 8. Using the Recovery and Supplementary CDsAppendix B. Getting help, service, and information Appendix C. Engine POST messages IBM Glossary of Storage Networking Terms Contents vi NAS 200 User’s Reference Figures Diagnostics panel LEDsBoot block jumper location Battery removal viii NAS 200 User’s Reference Tables x NAS 200 User’s Reference About this book Who should read this bookFrequently used terms Publications Web sites Hardcopy publications shipped with the NASRelated publications Chapter 1. Introduction Roadmap for setting up and configuring the NAS Microsoft Windows Terminal ServicesMicrosoft Services for UNIX IBM Advanced Appliance Configuration Utility agent Step 3 - Completing setup “Chapter 5. Completing setup” on page Step 1 - Initial network setup “Chapter 3. Getting started” on pageStep 2 - Define storage “Chapter 4. Storage configuration” on page 4 NAS 200 User’s Reference Chapter 2. Configuration and administration tools Using a keyboard, monitor, and mouse for setup and configuration Main functions Terminal Services ClientAdministration Tool IBM Advanced Appliance Configuration Utility IAACU Universal Manageability ServicesWindows 2000 for Network Attached Storage Chapter 2. Configuration and administration tools 2. Click Start → Run Terminal Services and the IBM NAS Administration ConsoleConnecting to the desktop through Terminal Services IBM Advanced Appliance Configuration Utility IBM NAS Administration consoleDetermining who is using the network-attached storage IAACU Agent IAACU Console v The Information Pane Discovering NAS 200 Appliancesv The Tree View Pane v Families Using Families and Groups in the Tree Viewv All Appliances v Orphaned Externally Configured Appliances v Orphaned Appliancesv Conflicting Network Addresses Creating a Family To create a Family Default Gateway Max IP AddressSubnet Mask No Allocation Universal Manageability Services System requirements Starting UM Services 2. Click Start Web-Based Management Launching UM Services from the configuration utilityWindows 2000 for Network Attached Storage Telnet Server support SNMP support Chapter 3. Getting started Methods for setting up your NASInstalling the IBM Advanced Appliance Configuration Utility Accessing Universal Management Services Initial setup and configuration Enabling National Language Support NLS Maintenance Date and TimeNetwork Setup v French v German v Japanese v Spanish 22 NAS 200 User’s Reference Chapter 4. Storage configuration ServeRAID configurationUpdating the ServeRAID BIOS, firmware, and device drivers RAID technology Solving ServeRAID problems Initial storage configuration of the NASCreating arrays and logical drives v Configuring the ServeRAID controller Format the logical drives 26 NAS 200 User’s Reference Chapter 5. Completing setup Defining Windows users and groupsDefining local Windows users and groups 1. Click Local Users v Click Identification Giving storage access to Windows domain users and groupsDefining UNIX users and groups Using a local UNIX name space 30 NAS 200 User’s Reference 1 Click Show user maps1 Click Show group maps Using the UNIX name space on an NIS domain 32 NAS 200 User’s Reference Creating shares4. Click New 9. Click OK. The new share should appear in the list of shares 34 NAS 200 User’s Reference Chapter 6. Additional administrative functions NAS Backup AssistantRestoring using the NT Backup panel Backup Operations Persistent Images Global Settings Volume Settings Volumes NameRead-only or read-write Retention value Schedules Restore Persistent ImagesDisaster Recovery Static IP addressing Creating a recovery diskBacking up the system drive If you have multiple 10/100 Ethernet adapters Restoring the system drive Granting user access to persistent image files 42 NAS 200 User’s Reference PSM notes Intel Ethernet adapter teaming Fault toleranceEthernet adapter teaming Alacritech Ethernet adapter teaming Load balancing 46 NAS 200 User’s Reference Chapter 7. Troubleshooting Engine troubleshooting and diagnosticsEngine diagnostic tools overview v POST beep codes, error messages, and error logs Identifying problems using LEDs Power-supply LEDs Table 3. Power-supply LEDS Chapter 7. Troubleshooting Light-path diagnostics Diagnostics panelFigure 1. Diagnostics panel LEDs MEM PS1 CPU PS2 PCI A PS3 PCI B NON PCI C OVER VRM NMI DASD TEMP 1. All known problems are resolved 2. The system is restarted Engine troubleshooting charts Page Monitor 54 NAS 200 User’s Reference Serial port problems Option problemsPower problems Service processor Software problemUSB port problems Universal Serial Bus Power problems Recovering BIOS Replacing the battery To replace the battery 5. Reinstall the appliance cover and connect the cables Integrated Ethernet adapter Adapter troubleshooting and diagnosticsNetwork connection problems Suggested Action Integrated Ethernet adapter troubleshooting chartEthernet adapter problem Troubleshooting the 10/100 PCI Ethernet adapter Table 8. 10/100 PCI Ethernet adapter troubleshooting chart Testing the Ethernet adapters with Intel PROSet Gigabit Ethernet SX adapter Table 9. Gigabit Ethernet SX adapter troubleshooting chart Table 10. Intel PRO 1000 XT Server adapter troubleshooting chart Troubleshooting the Intel PRO 1000 XT Server adapterTable 9. Gigabit Ethernet SX adapter troubleshooting chart continued 68 NAS 200 User’s Reference Troubleshooting the Alacritech Quad-Port 10/100 Ethernet adapter Indicator lights Troubleshooting the ServeRAID-4Lx and 4H Testing the Quad-Port 10/100 Ethernet adapter POST ISPR error procedures ServeRAID-4x problems and actions Do not press F5. Doing so changes the configuration9ZXX thru BZXX FFFF or other code not listed Testing the ServeRAID 4x adapter Table 12. ServeRAID-4x problems and actions Troubleshooting the Integrated System Management Processor 2. Select Backup IPS ServeRaid ConfigEnter Run Adapter Self-tests Troubleshooting the Remote Supervisor Adapter Testing SCSI Adapters 76 NAS 200 User’s Reference Chapter 8. Using the Recovery and Supplementary CDs Using the Recovery Enablement Diskette and Recovery CD Set 78 NAS 200 User’s Reference Directory Name Using the Supplementary CDContents Services for UNIX Appendix A. Notices ServeRAID ServerGuide TotalStorage TrademarksIBM Netfinity Netfinity Advanced System Management Netfinity Manager Appendix B. Getting help, service, and information Service support Before you call for service Getting customer support and service Getting help by telephone Appendix B. Getting help, service, and information 86 NAS 200 User’s Reference Power-on self-test POST Appendix C. Engine POST messagesPOST beep code descriptions No beeps Two short beeps Three short beepsRepeating short beeps One long and one short beep POST beep codes Table 15. POST beep codes 90 NAS 200 User’s Reference boot reset. See the Hardware Installation GuideTable 15. POST beep codes continued Symptom POST error messages Table 17. POST error messages continued 94 NAS 200 User’s Reference Error 96 NAS 200 User’s Reference Event/error logs POST diagnostic programs Starting the diagnostic programs Text messagesPassed User Aborted 2. Power on the NAS 200 and watch the screen Diagnostic error message tables Viewing the test log Error Code 102 NAS 200 User’s Reference Error Code 104 NAS 200 User’s Reference 405-XXX-00N Adapter in PCI slot N415-XXX-000 Cable 106 NAS 200 User’s Reference This glossary includes terms and definitions from IBM Glossary of Storage Networking TermsNumerics ASM see advanced system management ATM see asynchronous transfer mode BIOS see Basic Input/Output System AUI see attachment unit interfacebonded interface see bond group bps see bits per second CIFS see Windows networking CHAP see Challenge Handshake Authorization ProtocolCDDI see Copper Distributed Data Interface DDP see distributed data processing DHCP see Dynamic Host Configuration ProtocolCRC see cyclic redundancy check CRU see customer-replaceable unit DLR see dynamic link routine DMA see Direct Memory Access distributed data processing DDP. Synonym for distributed processingDNS see domain name system EIA see Electronic Industries Association ESD see electrostatic discharge ESM see environmental service monitor fiber optic cable see optical cable FIR see File Image Restore FIC see File Image CaptureFRU see field-replaceable unit FTP see File Transfer Protocol FVC see floating virtual connection IP see Internet Protocol HTTP see Hypertext Transfer ProtocolIETF see Internet Engineering Task Force LBG see load-balancing group LDAP see Lightweight Directory Access ProtocolLAN see local area network LS0H see Low-smoke zero halogen MES see miscellaneous equipment specificationLSFR0H see Low-smoke fire-retardant zero halogen NIS see network information services multicast address see LAN multicastN see Newton NDMP see network data management protocol PPS see per port switching PCI see Peripheral Component InterconnectPCNFS see personal-computer network file system PCNFSD see personal-computer NFS daemon RAM see random access memory PSM see Persistent Storage ManagerRAID see redundant array of independent disks SCSI see small computer system interface STP see shielded twisted pair SVN see switched virtual network SNMP see Simple Network Management ProtocolTCP see Transmission Control Protocol TCP/IP see Transmission Control Protocol/Internet Protocol TSM see Tivoli Storage Manager USB see universal serial busVLAN see virtual local area network VLUN see virtual logical unit WINS see Windows Internet Naming Service 124 NAS 200 User’s Reference Index A Page Page GA27-4263-01