EQ remove | Klark Teknik DN9344E, DN9340E guide

Operation: DN9340E

EQ remove page

This page allows the currently selected PEQ section to be deleted entirely (as opposed to bypassed see IN/OUT below). The centre encoder is turned clockwise to remove the section, and then the right encoder is also turned clockwise to confirm.

6.3.2Touchstrip operation with Parametric equalisation

On the Parametric EQ page, the touchstrip can be used to select the currently active section of EQ as an alternative to using the encoder knobs. If you are not currently using the Freq/Level menu, the unit automatically switches to it when you press the touchstrip. Press either the upper or lower part of the strip below the centre frequency of the required section. The centre frequency will highlight to indicate the selection. Once selected, the frequency of the EQ section can be dragged up and down the display by pressing the touchstrip and sliding the point of contact to left and right. There is no difference between the upper and lower strips when in Parametric mode.

19

Image 29

Klark Teknik DN9344E, DN9340E specifications Touchstrip operation with Parametric equalisation, EQ remove

Contents

DN9340E/DN9344E Page Important Safety Instructions Page Declaration of Conformity Page Contents Setup Menu DN9340E Application Notes Page After Unpacking Safety WarningInstallation Considerations Page DN9340E Front Panel Quick Reference DN9344E Front Panel Key Features DN9340E & DN9344E Key FeaturesIntroducing the DN9340E/DN9344E Host Software Versions Space efficiency Remote control operationInterface to Midas consoles Store and Recall Parameters EQ Access and Displays Controls, Connectors, Indicators DN9340EFront Panel DN9340E Soft keys display Soft keys Selected channel both channels if linked. When aBypass, Channel Select, Soft Keys and Alphanumeric Display Touch Strip, Store and Recall, Home Setup and Data Entry PC Port, Metering and Power Mains Rear Panel DN9340EInputs a and B Word clock Input Signal Flow DN9340E Signal Flow DN9340E Operation DN9340E Operation DN9340EHome Home page sub-menus Touchstrip Operation on the Home Soft Key Functions Graphic Equalisation EQ Flat Automatic features Grouping Touchstrip operation with Graphic equalisation Parametric Equalisation EQ remove Touchstrip operation with Parametric equalisation Hi Threshold / Level Dynamic EqualisationLo Threshold / Level Time constants Touchstrip operation with Dynamic equalisation Filter Type Left Encoder Centre Encoder Right Encoder FiltersCreate Filter function Filter remove Filter settingsTouchstrip operation with Filters Metering Clear Down Sequence Setup Menu DN9340E Setup Menu DN9340ETo access the Set Up menu pages General To switch remote communications off Remote control via a PCComms channel To select a slave remote communications channel To select a master remote communications channel Using a DN9340E for master controlTo select a slave communications channel To remove the unit from the network To remove the Panel Lock Front Panel lockTo set a Panel Lock To change the input source Analogue/Digital Input Select To set a Presets lock Presets lockDigital Output Clock Select To select the output clock source Delay options LCD contrast adjustmentNaming Pages 7 To enter a name Ethernet IP Address Power-up LogoEthernet Settings Pages 11 To check and edit the Subnet Mask Ethernet Subnet Mask Setup To recall settings Using the DN9340E MemoriesTo store settings Connections Remote ControlAddresses Data model Getting started Setting the master unit on-lineOn a DN9340E On a DN9344E System naming To set up the namesOperation Solo Tracking operation To set up the assignmentCopy channel function Helix DN9340E/DN9344E unit interconnections Overview Connecting the Helix DN9340/DN9344E units in a daisy chain Ethernet connection standard Ethernet connection wireless optionEthernet Connection Configuring the DN9344E for Network Communication Configuring the DN9340E for Network Communication Serial connection details Connection and Configuration ProcedureSerial Connection Option Alphanumeric displays, SETUP, Metering and Power Controls, Connectors, Indicators DN9344EPress to step through the Set Up pages Power Switch Power on Power on indication Power indication Indicators Indicators, Up and Down Buttons, PC Port and Scribble Strips Mains inlet socket Rear Panel DN9344E1B, 2A and 2B Interface Signal Flow DN9344E Signal Flow DN9344E Remote Comms channels Operation DN9344EOperation DN9344E To select a remote communications channel To disable remote communications and relay operation To enable the Contact Closure Relay mode To set a password PasswordTo change the settings for Inputs 1A and 1B Analogue/Digital Input Select Pages 3 Digital Output Clock Select Pages 5 To change the settings for Output Subnet Mask Ethernet SettingsTo change the IP address To change the Subnet Mask Dynamic EQ Application Notes Application Notes Application Notes What do we mean by all these Q types? Constant Q Proportional Q Symmetrical Q What is AES/EBU? 17.1. DN9340E Technical Specification DN9340E Power Requirements 17.2. DN9344E Technical Specification DN9344E Relay Socket Pin D-type rear Power Pin IEC Replacement Service InformationBattery