Manuals / Kodak / Computer Equipment / Scanner

Kodak 7520 manual Code, Message Displayed, Description/Action Required

Models: 7520

1 127

Download 127 pages 33.15 Kb

Page 63

Code	Message Displayed	Description/Action Required

E234	Press JOG to remove docs	When pressing Run, a document was detected
		under a document sensor. Press Jog to move all
		documents in the transport system, then press Run
		and rescan any documents that have not been
		scanned.

E235	Controlled power-down reqrd	This message is displayed along with a more detailed
		error message.
		∙ Turn the side panel switch off.
		∙ Turn the main power switch off.
		∙ Wait 5 to 10 seconds.
		∙ Turn the main power switch on.
		∙ Turn the side panel switch on.
		If the error repeats, call Service.

E241	Enter correct IA, re-scan	The patch document fed conflicts with the Level key
		pressed. Verify the current image level and image
		address. If necessary, alter the image level or image
		address using the Level keys or Next key or press
		Run and rescan the patch document.

E244	Enter correct IA, re-scan	The T-patch document was fed and then followed by
		a 2-patch or 3-patch document which conflicted with
		the level of the T-patch. Verify the current image level
		and image address. If necessary, alter the image
		level or image address using the Level keys, or Next
		key or press Run and rescan the T-patch,
		2-patch or 3-patch document.

E245	Enter correct IA, re-scan	Two T-patch documents were fed one right after the
		other. Verify the current image level and image
		address. If necessary, alter the image level or image
		address using the Level keys or Next key. Do not
		scan another T-patch document.

E246	Enter correct IA, re-scan	The T-patch document fed conflicts with the level of
		the image address entered. Verify the current image
		level and image address and if necessary, alter the
		image level or image address using the Level keys or
		Next key. Do not scan another T-patch document.

E250	Frnt illumination failure	A front lamp failure was detected while the front lamp
		was illuminated. Press Cal to calibrate the scanner. If
		the error persists, verify the optical path is free of
		obstructions, clean the imaging guides and replace
		the front and rear (duplex scanners) lamps.

A-61140 January 2000

6-7

Image 63

Kodak 7520 manual Code, Message Displayed, Description/Action Required

Contents

User’s Guide Document ScannerA-61140 Part No. 1E8149 IMPORTANT Equipment shall be installed by qualified personnel Taiwan Japan Acoustic EmissionElectroMagnetic Compatibility Statements United StatesFootswitch Workstation Endorser CongratulationsBar Code Reader Document Printer front and/or rear Patch Reader 1 Introduction Scanner featuresScanner options Front View - Document Scanner Scanner componentsFor European units only Rear View - Document ScannerStatus display Control panelFunction indicatorsKey/Indicator Operating keys andOperating keys and indicators Keys/IndicatorsFunction Turning on the scanner 2 Getting StartedSelecting the language display Calibrating the scanner Document sizes Preparing documents for scanningUnsuccessful calibration Document orientationgap semi-automatic feeder Adjusting the feed and separator roller4. Press Run Adjusting the separator roller to scan thick documents Adjusting the feed shelf position semi Adjusting the side guidesautomatic feeder only Adjusting the exit hopper side guides and end stop ∙ Standard position ∙ 10 from standard position Overview 3 Operating the ScannerSetting Levels Setting image levels Selecting a modeTemporary operating values Feeding documents using the semi- automatic feeder Feeding documents manually Feeding thick documents Feeding documents using the automatic feeder 4 Function Codes Using function codesIndex/Image Address SetupFunction code summary Application ModesFootswitch Bar Code ReaderDocument Printers Description Function code listingCode Function Code NameCode Function Code NameDescription Description EnterCode Function Code NameEnter CodeFunction Code Name DescriptionCleaning tasks Cleaning materials Replacement parts 5 MaintenanceCleaning the imaging guides Daily maintenance procedures6. Dry the imaging guides with a dry, lint-free cloth 10. Close the side access door CAUTION Open and close the doors slowly Cleaning the feed and separator rollers semi- automatic feeder6. Clean the surface of the feed roller assembly with a dry cloth To clean the feeder module and separator roller Cleaning the feeder module and separator roller automatic feederCleaning the separator roller To clean the paper path CAUTION Open and close the doors slowly Weekly maintenance proceduresVacuuming inside the scanner Vacuuming the horizontal transport areaPage 5-12 Vacuuming inside the side access door1. Turn the power off 2. Open the side access door 3. Open the upper access doorCleaning the cabinet Changing the lamps Replacement proceduresCAUTION Lamps are fragile. Do not force the lamp into place 10. Close the side access door Replacing the imaging guides 5. Grasp and hold the new lower imaging guide by the green handle and carefully slide it into place. Make sure the grooves fully engage the track 8. Close the side access door Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials Chapter 2, Getting Started Chapter 3, Operating the Scanner Chapter 7, TroubleshootingService Errors 6 Operator MessagesControlled power- down sequence Code Operator message listingMessage Displayed Description/Action RequiredCode Message DisplayedDescription/Action Required Code Message DisplayedDescription/Action Required Description/Action Required Document Image Manager referred to as SABRECode Message DisplayedCode Message DisplayedDescription/Action Required Code Message DisplayedDescription/Action Required Code Message DisplayedDescription/Action Required Probable Cause 7 TroubleshootingTrouble and remedy chart TroubleTrouble Probable CauseRemedy Trouble Clearing thedocument path The document pathClearing documents CAUTION Open and close the doors slowly The feeder areaHorizontal transport plate, lower belt module and lower turn areas CAUTION Open and close the doors slowlyA-61140 January 5. Remove all jammed documents 4. Remove all jammed documents Vertical transport plate and imaging guide areas1. Turn off the power switch 2. Open the side access door To clear the vertical transport plate and imaging guide areas Area B6. Close the side access door Removing non-jammed documents Document exit and upper turn roller areasSupply 8 AccessoriesSupplies Imaging Station LampsUnited States and Canada Parts and toolsPart/Tool Order NumberUsing the Bar Code Reader Code Type Bar code typesAvailable Start/StopBefore you begin Enabling bar code reading Enabling the bar code confirmation tone Performing a bar code test CAUTION Open and close the doors slowly Using the Evaluate option4. Lift the release bar to raise the front scan module Rear imaging guide Front imagingguide Vertical transport plateTransparent adhesive tape Document and surrounding textFront image guide surface facing the rear of the Bar code should face the front of the scanner11. Replace the imaging guide with the bar code attached to it BC Type = Not found MessageMessage BC Type = Please WaitReflectance Fields Grades A through F Dimensional Fields Pass or Faileither dimensional or reflectance fields Evaluating test resultsA Pass Table 1 - Bar Code GradesGrade FieldCode Made Easy, A-61099 Problem TypeTable 2 - Common Causes of Low Bar Code Ratings CauseMessage Using the Display optionBar code was not read MessageThis display gives the decoded value of the bar code read including the *, representing the start character is greater than 15. To see the remaining value, press Enter until all characters have been displayed MessageUsing the Read Rate option Action Using the FootswitchEnabling the confirmation tone Footswitch Pressed actions Footswitch PressedAction Footswitch Released actionsFootswitch Released Footswitch PressedPatch types Using the Patch ReaderPatch code placement Printing patches Patch Reading function codes CAUTION Open and close the doors slowly Cleaning the Patch ReaderChanging the horizontal read position IMPORTANT Do not remove the cable tie from the Patch ReaderUsing the Document Printer Rear Document Front and rear Document Printer overviewsFront and Rear Document Printer Mounting Plate Views Front DocumentChanging the vertical start print position Vertical start print positionCAUTION Open and close the lower access door slowly Horizontal print positionFront print positions IMPORTANT When repositioning the front Document Printer, be sure the cable magnet is secured to the front Document Printer mounting plate not on the Patch Reader mounting plate, so the printer flat cable does not interfere with the optical path between the front imaging guide and the front scan module Function codes Using the Print Test function Cleaning the ink cartridge Front Document PrinterCAUTION Open and close the doors slowly 6. Raise the holding bar up from the ink cartridge and carriage 13. Slide the ink cartridge back into the carriage Rear Document Printer 12. Slide the ink cartridge back into the carriage Replacing the ink cartridge Replacing the front Document Printer ink cartridgeCAUTION Open and close the doors slowly 6. Raise the holding bar Press spring clips Cable magnet not shown Replacing the rear Document Printer ink cartridgeMode Appendix A Basic ConceptsModes EnabledImage addresses Using the Next key Assigning an image addressEnter Using Function Code F92 Image address formats Indexing schemesSingle level indexing Page Two level indexingeach document is defined as follows Three level indexing Page…1-40 Three level offset indexing Controlling document level changes Checking the meters Special considerationsPrinted on recycled paper DOCUMENT I M A G I N GEASTMAN KODAK COMPANY Document Imaging Rochester, New York A-61140 2/2000 Eastman Kodak Company Printed in U.S.A