Korg D3200 owner manual 153, Early Reflection, C/R Delay, Stereo/Cross Delay

EQ Trim	–15...+15dB
	Sets the equalizer trim level
LEQ Gain (Pre LEQ Gain)	–15...+15dB
	Sets the gain of Low EQ
HEQ Gain (Pre HEQ Gain)	–15...+15dB
	Sets the gain of High EQ
P.DlyThru (Pre Delay Thru)	0...100%
Sets the mix ratio of non-delay sound
Rev Level (Reverb Level)	0...100%
	Sets the reverberation level
ER Level	0...100%
	Sets the level of early reflections

: ER Level, : Reverb Level

These parameters set the early reflection level and reverb level. Changing these parameter values allows you to simulate the type of walls in the room. That is, a larger “ER Level” simulates a hard wall, and a larger “Reverb Level” simulates a soft wall.

7: Early Reflection

This effect is only the early reflection part of a reverberation sound, and adds presence to the sound. You can select one of the four decay curves.

Type	Sharp, Loose, Modulated, Reverse
Selects the decay curve for the early reflection
ER Time	10...800msec
	Sets the time length of early reflection
Predly (Pre Delay)	0...200msec

Sets the time taken from the original sound to the first early reflection

EQ Trim	–15...+15dB
	Sets the equalizer trim level
LEQ Gain (Pre LEQ Gain)	–15...+15dB
	Sets the gain of Low EQ
HEQ Gain (Pre HEQ Gain)	–15...+15dB
	Sets the gain of High EQ
Dry:Wet	Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

: Type

This parameter selects the decay curve for the early reflection.

8: L/C/R Delay

This multitap delay outputs three Tap signals to the left, right, and center respectively. You can also adjust the left and right spread of the delay sound.

L Time (L Delay Time)	0...2.730sec
	Sets the delay time of TapL
C Time (C Delay Time)	0...2.730sec
	Sets the delay time of TapC
R Time (R Delay Time)	0...2.730sec
	Sets the delay time of TapR
Dry:Wet	Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
L LevelL (Delay Level)	0...100%
	Sets the output level of TapL
C LevelC (Delay Level)	0...100%
	Sets the output level of TapC
R LevelR (Delay Level)	0...100%
	Sets the output level of TapR
Spread	0...100%
Sets the width of the stereo image of the effect sound
Fdback (C) (Feedback (C Delay))	–100...+100%

Sets the feedback amount of TapC

Fb.LoDamp (Feedback Low Damp)	THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
Fb.HiDamp (Feedback High Damp)	53Hz...20.0kHz, THRU
Sets the damping amount in the high range
In Level (Input Level)	0...100%

Sets the input level to the effect

: High Damp, : Low Damp

These parameters set the damping amount of high range and low range. The tone of the delayed sound becomes darker and lighter as it feeds back.

: Spread

This parameter sets the pan width of the effect sound. The stereo image is widest with a value of “50,” and the effect sound of both channels is output from the center with a value of “0.”

9: Stereo/Cross Delay

This is a stereo delay, and can by used as a cross-feedback de- lay effect in which the delay sounds cross over between the left and right by changing the feedback routing.

L Time (L Delay Time)	0...2.730sec
	Sets the left delay time
R Time (R Delay Time)	0...2.730sec
	Sets the right delay time
Type (Stereo/Cross)	Stereo, Cross
Switches between stereo delay and cross-feedback delay
Dry:Wet	Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
L Fdback (L Feedback)	–100...+100%
Sets the feedback amount for the left channel
R Fdback (R Feedback)	–100...+100%
Sets the feedback amount for the right channel
LoDamp (Low Damp)	THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp)	53Hz...20.0kHz, THRU
Sets the damping amount in the high range
Spread	0...100%
Sets the width of the stereo image of the effect sound
In Level (Input Level)	0...100%
	Sets the input level to the effect

10:St. Multitap Delay (Stereo Multitap Delay)

The left and right Multitap Delays have two taps respective- ly. Changing the routing of feedback and tap output allows you to create various patterns of complex effect sounds.

Tap1Time		0...2.730sec
		Sets the delay time of Tap1
Tap2Time		0...2.730sec
		Sets the delay time of Tap2
Type	Normal, CrossFdback, CrossPan1, CrossPan2
	Switches the left and right delay routing
Dry:Wet		Dry, 1:99...99:1, Wet
	Sets the balance between the effect and dry sounds
Tap1Level		0...100%
		Sets the output level of Tap1
Tap2Level		0...100%
		Sets the output level of Tap2
T1.Fdback (Tap1 Feedback)		–100...+100%
		Sets the Tap1 feedback amount
Spread		0...100%
	Sets the width of the stereo image of the effect sound

Algorithm list
Program list
Stereo type	Algorithm
Monaural type	Algorithm

Effect

153