Korg D3200 owner manual 125

These messages will be received only if Automation (→p.103) is turned off.

3. Global Ch [01…16]

This sets the Global MIDI Channel.

If you want to use program change messages to transmit and receive scene changes, use a MIDI cable to connect your external MIDI device to the D3200, and set the MIDI channel of your connected device to the same MIDI chan- nel as the D3200’s “Global Ch” so that MIDI messages can be transmitted and received.

4. MMC Device ID [000…127]

Specifies the device ID that will be used to transmit and receive MMC.

In order to transmit or receive MMC, you must use a MIDI cable to connect the D3200 and the external MIDI device, set the two devices to the same Device ID, and make the appropriate setting in “MMC Mode.”

If this is set to 127, the D3200 can transmit and receive MMC commands to and from units of any device ID setting.

5. Mode [Transmit, Receive, Off]

This sets the MMC transmission/reception mode.

Transmit: MMC will be transmitted. In this case, the MIDI Sync setting will automatically be set to MTC Slave.

Receive: MMC will be received. In this case, the MIDI Sync setting will automatically be set to MTC Master.

Off: MMC will not be used.

6.Frame Rate

This selects the frame rate that is used when MIDI Sync

is set to “MTC Master” or “MTC Slave.”

Set this to the same frame rate as used on the external device with which you are synchronizing.

30:30 fps (30 frames per second, non-drop) 29NDF: 29.97 fps (29 frames per second, non-drop) 29DF: 29.97 fps (29 frames per second, drop)

25:25 fps (25 frames per second, non-drop)

24:24 fps (24 frames per second, non-drop)

7.Time Code Offset [00:00:00.00F…23:59:59.29F] (for frame rate 30)

This specifies an offset value that will be reflected in the counter.

The offset value you specify here will be the starting value for the counter. This will apply when the counter is set to display frames and MTC/MMC is enabled.

8.MIDI Sync

[MIDIClockMaster, Off, MTC Master, MTC Slave]

This selects the synchronization mode used when syn- chronizing via the MIDI IN/OUT connectors.

MIDIClockMaster: MIDI clock data will be transmitted.

Off: Synchronization messages will not be transmitted or received.

MTC Master: The D3200 will operate as the master de- vice. At this time if the MMC Mode is set to Transmit, the Chase Mode setting will automatically be turned Off.

MTC Slave: The D3200 will operate as the slave device. At this time if the MMC Mode is set to Re- ceive, the Chase Mode setting will auto- matically be turned ON.

9. Chase Mode [ON, OFF]

This is available if “MIDI Sync” is set to “MTC Slave.”

ON: When MTC synchronization begins, playback will chase the MTC messages. After playback begins, if two seconds or more elapse without a MTC mes- sage being received, and there is a discrepancy of two seconds or more between the MTC messages and the current location of the D3200, playback will stop and wait for MTC synchronization to resume.

OFF: MTC messages will be chased during playback only when MTC synchronization begins. Once playback begins, it will continue even if the received time code no longer matches the internal time code or if time code stops arriving.

If you are synchronizing with a device other than the D3200 as the MTC master, incompatibilities between the devices may cause synchronization problems unless you play back from the beginning of the song.

Counter	Rename
METER
MIXER
CH	VIEW
EFFECT
SEND
EQ
PAN
SONG
SYSTEM	/MIDI
TRACK
CD

Reference
	UNDO
	TUNER
	SESSION	DRUMS
	STORE	SCENE
	MARK
	SCRUB
	1/IN ...	4/END
	LOC	LOC
	REC/PLAY	MODE
	Transport	keys

125