Korg D3200 owner manual Adjusting the cue level, Solo settings, Muting a channel

You can also turn “Drums” on by setting the SESSION

DRUMS, “DrmsMixer” tab page parameter Assign to Monitor.

(3)Adjust the monitor volume.

The monitor volume is adjusted by the MONITOR LEVEL knob for the MONITOR L/R jacks, and by the PHONES LEVEL knob and MONITOR LEVEL for the PHONES jacks.

3-8. Adjusting the cue level

Cue Level is a function that lets you adjust the monitor vol- ume and pan independently of the settings of the master bus. The cue signal is output from the MONITOR L/R jacks and the PHONES jacks.

(1)Select cue as the source for monitoring.

In the MIXER, SOLO/MONITOR, “Monitor” tab page, click the “Cue” and turn it on (highlighted).

If you have made “Solo” settings, defeat “Solo” before you select Cue.

(2)Adjust the cue level.

Access the MIXER, SOLO/MONITOR, “CueLevel” tab page.

If you click the “LEVEL” knob icon, you can use the Knob Matrix to adjust the volume of each channel.

If you click the “PAN” knob icon, you can use the Knob Matrix to adjust the pan of each channel.

Alternatively, you can click a channel icon and use the

buttons, value dial, or +/– keys to adjust the volume level and pan.

3-9. Solo settings

Use the Solo function when you want to listen to only a spe- cific channel(s) without affecting the signal being recorded or sent to the MASTER L/R bus. You can also use the solo when you want to listen to one of the Send signals or to one of the Return signals from one of the internal master effects. The solo signal is output from the MONITOR L/R jacks and the PHONES jacks.

Soloing just one channel

(1)Access the MIXER, SOLO/MONITOR, “Solo” tab page.

(2)Use the Mode radio buttons to click “Last.”

(3)Press the SOLO key to select SOLO mode. The channel keys of all channels will blink.

(4)Press the channel key for the channel you want to solo. The key of the selected channel will continue blinking, and the keys of the other channels will go dark.

(5)Listen to the soloed signal.

As an alternative to using the channel key to select solo, you can click a button in the MIXER, SOLO/MONITOR, “Solo” tab page. This method allows you to select a Send or Return signal for soloing, as well as the signal of a channel (→p.110).

Soloing more than one channel

(1)Access the MIXER, SOLO/MONITOR, “Solo” tab page.

(2)Use the Mode radio buttons to click “Mix.”

(3)Use steps (3) and (4) in “Soloing just one channel” (above) to select the channels that you want to solo.

Cancelling solo

(1)Access the MIXER, SOLO/MONITOR, “Solo” tab page, and click off the button(s) that you selected for soloing.

If you want to clear all solo settings, click the Clear All button.

You can defeat Solo by pressing the REC/PLAY, CH ON, SOLO, or CH SELECT keys.

(2)Verify the setting.

In the “Monitor” tab page, verify that Solo is now off.

Sending the soloed audio from the master bus

If you want to, you can send the soloed audio signal to the MASTER L/R jacks. Use this when you want to hear the solo- ed audio through the monitor system connected to the MAS- TER L/R jacks.

In the MIXER, SOLO/MONITOR, “Solo” tab page, click the Solo→Master button on (highlighted).

3-10. Muting a channel

You can turn the CH ON key on and use the channel keys to mute (silence) each channel.

(1)Turn on the CH ON key.

The channel keys of all channels will light.

(2)When you press the channel key of a channel, it will be muted (the key will be dark).

48