Creating a fade-out

Fading-out the IN–OUT region of track 1

(1)Specify the region that you want to fade-out.

Set the following locations to specify the region where the fade-out will occur (p.69).

Set the IN point to specify the beginning of the region where the fade-out will occur.

Set the OUT point to specify the end of the region where the fade-out will occur.

(2)Select “FadeTrk.”

In the TRACK, “EditTrk” tab page, click the Edit Trk Type cell. In the Edit Trk Type dialog box, click “Fade- Trk” and click the OK button (or press the panel YES key).

(3)Select the fade-out curve.

Click the Mode button to display the Fade Mode dialog box.

A.B.C: Fade-in curve

D.E.F: Fade-out curve

For details on how these curves differ, refer to “Fade- Trk” (p.133).

For this example, select the type “D” curve and click the OK button (or press the panel YES key) to return to the “EditTrk” tab page.

(4)Select the track number that you want to fade-out.

Click the popup button of the Destination cell, and choose track “1” in the Destination Track dialog box. You can also click the cell to select this.

Check the IN and OUT locations. If you want to set the locations with more precision, click the Destina-

tion WAVE button, and use the Wave dialog box (p.128) to set the location.

(5)Execute the editing operation.

Click the Exec. button. Then in the FadeTrk dialog box, click the Yes button (or press the panel YES key) to exe- cute the operation.

When the operation is finished, the display will indicate “Completed.” Click the OK button (or press the panel YES key).

(6)Check the results of the editing operation.

Press the LOC 1/IN key, and play back from the IN loca- tion to verify that the operation has done correctly.

If you are not satisfied with the results, you can use Undo to return to the previous state. (p.141)

The length of the IN–OUT area specified will determine the amount of time it takes to complete the Fade operation.

Boosting the maximum volume to the specified level (Normalize: NormalizeTrk)

If the recorded level of a track is too low, you can use the Nor- malize operation to boost the overall level of the specified re- gion (IN–OUT) so that the maximum recorded level will equal the specified level.

You can normalize one track or simultaneously normalize the data of adjacent tracks.

If you boost data that was recorded at an extremely low level, any noise in that region will also be boosted.

Normalizing the IN–OUT region of track 1

(1)Specify the region that you want to normalize.

Set the following locations to specify the region for nor- malize (p.69).

Set the IN point to specify the beginning of the region to be normalized.

Set the OUT point to specify the end of the region to be normalized.

(2)Select “NormalizeTrk.”

In the TRACK, “EditTrk” tab page, click the Edit Trk Type cell. In the Edit Trk Type dialog box, click “NormalizeTrk” and click the OK button (or press the panel YES key).

(3)Specify the maximum level.

Click the Mode button to display the Normalize Mode dialog box. Set the “Normalize Gain Level” value, and click the OK button (or press the panel YES key).

(4)Select the track number that you want to normalize.

Click the popup button of the Destination cell, and choose track “1” in the Destination Track dialog box. You can also click the cell to select this.

Check the IN and OUT locations. If you want to set the locations with more precision, click the Destina-

tion WAVE button, and use the Wave dialog box (p.128) to set the location.

(5)Execute the editing operation.

Click the Exec. button. Then in the NormalizeTrk dialog box, click the Yes button (or press the panel YES key) to execute the operation.

When the operation is finished, the display will indicate “Completed.” Click the OK button (or press the panel YES key).

(2)

(4)

(3)

(5)

(6)Check the results of the editing operation.

Press the LOC 1/IN key, and play back from the IN loca- tion to verify that the data was normalize correctly.

If you are not satisfied with the results, you can use Undo to return to the previous state. (p.141)

The length of the IN–OUT area specified will determine the amount of time it takes to complete the Normalize operation.

 

Song,

Locate

 

Mixer

 

 

 

 

 

 

Effects

 

 

 

 

 

 

Session

Drums™

 

 

 

 

 

 

 

 

 

Recorder

 

 

 

 

 

 

 

Operation

 

 

 

 

 

CD

 

 

 

 

Data

 

 

 

 

 

 

Drive

 

 

 

 

 

 

USB

 

 

 

 

 

 

MIDI

 

 

 

 

 

 

Upgrading

the system

 

 

 

Recovery

CD

 

 

ClickPoint

calibration

 

 

 

 

 

77

Page 87
Image 87
Korg D3200 owner manual Creating a fade-out