To erase A and B that remain from the first take, and recover disk space

Execute the TRACK “EditTrk” tab page “OptimizeTrk” (op- timize) command on track 1 for the region between the be- ginning and end of the song.

When this is executed, only the audio data of the Intro, 2nd take of A (A’), 2nd take of B (B’), and the Break will be kept. This means that the 1st take of A and 1st take of B data will no longer occupy disk space.

Intro

A

B

Break

 

A'

B'

 

IN

 

“OptimizeTrack”

OUT

 

 

 

Intro

A'

B'

Break

 

 

3. You recorded A and B on track 1 as the first take. As the second take, you overwrite-recorded the Intro, A’, B’, and Break.

A B

1st take

1st take

2nd take

Intro

A'

B'

Break

In this case, the first take A and B remain “beneath” A’ and B’, but since the audio data of take 1 is not used at all once you finished recording take 2, there is no need to execute the optimize command.

Deleting the Undo data

Even if you use the drive space efficiently as described above ( ), the old data will be kept on the drive for use by the Undo function.

To delete this undo data, either click the Clear button in the “Undo/Redo” tab page (p.141), or put the D3200 in stand- by mode (shut down). After restarting, all undo data will be deleted, recovering free space on the drive.

Be aware that restarting the D3200 will delete the undo data of all the songs.

Sharing event data

If you use the Copy Track operation to copy track data to an- other track (e.g., virtual track) or another song, this audio data will be shared, so that the drive capacity will not de- crease. However if you execute the Optimize Track operation on the copy-destination or copy-source track, new audio data will be created, and this will mean that a greater amount of drive capacity will be used than before the operation was ex- ecuted.

In the case of 2 above, if you copy the first take to another track before you record the second time, then executing the Optimize Track operation will not delete the “A” and “B” re- gions of the first take, and new audio data for the “Intro” and “Break” regions will be created, meaning that a greater amount of drive capacity will be used.

8. PC drive

The PC drive is an area used to share data with your compu- ter. Its size may be set to 2, 4 or 8 GB (p.89 “1-2. Specifying the PC drive size”).

You can use the SYSTEM/MIDI, “PC File” tab page com- mand to check, rename, or delete files on the PC drive. The PC drive contains the following folders, which contain the following files.

BACKUP folder: backup files

WAV folder: audio files in WAV format

D3200 folder:

This folder contains system files for updating the system.

Checking, renaming, or deleting files

You can check the size, rename, or delete files that are on the PC drive.

(1)Access the SYSTEM/MIDI, “PC File” tab page.

To move to a lower level, select a folder and click the Open button.

To return to the next upper level, click the Close button.

(2)To rename a file, select the file, click the Rename but- ton, and rename the file (p.36).

For details on the file names you can use, refer to “More about drives and files” (p.171).

(3)To delete a file, select the file and click the Delete but- ton.

The display will ask “Are You Sure?” Click the Yes button (or press the panel YES key) to delete the file.

If you decide not to delete the file, click the No button (or press the panel NO key).

When the file has been deleted, the display will indi- cate “Completed.” Click the OK button (or press the panel YES key).

92

Page 102
Image 102
Korg D3200 owner manual PC drive, Checking, renaming, or deleting files, Deleting the Undo data, Sharing event data