Korg D3200 owner manual 164

Appendices

Troubleshooting

Power does not turn on

Is the power cable connected to an outlet? (→p.1)

Is the rear panel POWER ON (power supply) switch turned on? (→p.1)

Nothing appears in the display

Is the top panel power on key lit? (→p.1)

Is the contrast adjusted correctly? (→p.8)

Vertical lines are visible in the display

Depending on the content of the display, vertical lines may be visible in the display, but this is not a malfunction.

→If the screen is difficult to read, adjust the contrast (→p.8).

No sound

Is the power of the D3200 or a connected device turned off? (→p.1)

Is the MASTER fader, MONITOR LEVEL knob, or PHONES LEVEL knobs set to low?

Is the channel volume level set to low?

The actual volume level may not match the fader posi- tions if pairing has been used and then switched off, or after automation has been used.

→Go to the MIXER, FADER/PAN/AUTOMATION, “Fader Pan” tab page, and raise and lower the fader to match the fader position to the actual volume. Then adjust the fader to an appropriate level.

Is the Solo function activated?

→If Solo is being used, you will not hear channels that are not being soloed.

Can’t hear the playback

With the REC/PLAY key on, are the channel keys set to Play mode for the appropriate tracks? (→p.8)

With the CH ON key on, are the channel keys turned On? (→p.8)

Has solo been turned on, so that other tracks are not heard? (→p.8, 99)

If you have selected Cue, could the cue level of the channels be lowered?

→Access the MIXER, SOLO/MONITOR, “CueLevel” tab page and raise the cue level. (→p.48)

Could the Trim level be turned down in the EFFECT, “InsertEFF” tab page?

→If a channel is assigned to an insert effect, the volume of that channel is determined by the Trim setting even if the insert effect is set to NO EFFECT.

Is the 1–16/17–32key set correctly? (→p.8)

Input sound is inaudible or too soft

Is the TRIM knob raised to an appropriate level?

After connecting your audio source to an input jack, did you assign it to a mixer channel?

→In the MIXER, CH INPUT/SubMixer, “Ch Assign” tab page, assign the source to a mixer channel. (→p.42)

Verify that audio is being input.

→Press the METER key, and in “Meter/Track View,” set “Select Level Meter Position” to “CH-Input.”Watch

the meters to verify that audio is being input to each mixer channel (→p.43).

With the REC/PLAY key on, are the channel keys set to Record mode? (→p.8)

Are the monitor settings appropriate?

→In the MIXER, SOLO/MONITOR, “Monitor” tab page, select the signal that you want to monitor (nor- mally, turn “MasterLR” On). If you have turned

“Rhythm” or “Cue” “On,” raise their volume levels. (→p.47)

With the CH ON key on, are the channel keys turned On? (→p.8)

Is the PAD key on?

Are you using INPUT1 and GUITAR IN simultaneously?

→INPUT1 and GUITAR IN are shared. If a guitar is con- nected to GUITAR IN, you cannot use INPUT1.

If cue is selected, the cue level of each channel may have been lowered.

→In the MIXER, SOLO/MONITOR, “CueLevel ” tab page. (→p.48)

Is the 1–16/17–32key set correctly? (→p.8)

Could the Trim level be turned down in the EFFECT, “InsertEFF” tab page?

→If a channel is assigned to an insert effect, the volume of that channel is determined by the Trim setting even if the insert effect is set to NO EFFECT.

No sound from AUX OUT

“Can’t apply external effect (AUX)” (→p.166)

No drum sound

Session drums “Drum sound is not output” (→p.166)

Can’t hear scrub playback

The incorrect track may be selected in the scrub page.

→Select the correct track.

Faders don’t work

Fader does not work

If you switch pairing off after channels were paired, or if you recall a scene, the audio level of a channel may not match the position of the fader.

→Raise or lower the fader so that it matches the actual volume level.

164