Korg D3200 owner manual 162, Mono Wah, 49 Mn.Ring Modulator Mono Ring Modulator

Dry:Wet	Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Waveform (LFO Waveform)	Triangle, Sine, Saw
	Selects LFO Waveform
LFO Speed	0.02...20.00Hz
	Sets the LFO speed
LFO Step	0...256
	Selects the LFO step
Env.Resp (Envelope Response)	Slow, Medium, Fast
Selects the response speed of envelope control
Env.Sens (Envelope Sensitivity)	0...100%
Sets the sensitivity of envelope control

47: Mono Wah

Control (Control Source)		Envelope, LFO, Manual
		Switches the control source
Wah.Type	Y-CRY, RM-A, RM-B, J-CRY, VOX, M-VOX
		Selects the wah type
Env.Resp (Envelope Response)		Slow, Medium, Fast
	Selects the response speed of envelope control
Env.Sens (Envelope Sensitivity)		0...100%
	Sets the sensitivity of envelope control
Waveform (LFO Waveform)		Triangle, Sine, Saw
		Selects LFO Waveform
*LFO Speed		0.02...20.00Hz
		Sets the LFO speed
LFO Step		0...256
		Selects the LFO step
*Manual (Manual Control)		0...100
	Sets the control position manually
DirectMix (Direct Mix Level)		0...100%
	Adjusts the mix level of the direct sound
Wah Level		0...100
		Sets the wah level

Category: SFX&etc

SFX/Etc effects

48:Mn.Analog Record (Mono Analog Record)

RPM	33 1/3, 45, 78
	Sets the r.p.m. of a record
Wah (Wah Flutter)	0...100%
Sets the depth by which the record is warped
Bend	0...100%
Sets the width by which the record is warped
Dry:Wet	Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
ClickLevel (Click Noise Level)	0...100%
	Sets the level of click noise
ClickAngle (Click Angle)	0...100
Sets the angle of the scratch on the surface of the record
LoDamp (Low Damp)	THRU, 21Hz...8.00kHz
Sets the damping amount in the low range
HiDamp (High Damp)	53Hz...20.0kHz, THRU
Sets the damping amount in the high range
ClickPoint	0...100
Sets the distance of the scratch from the warped area
WhiteLevel (White Noise Level)	0...100%
	Sets the level of white noise

NoiseLoCut (Noise Low Cut)	THRU, 21Hz...8.00kHz
Sets the low-cut frequency for the noise
NoiseHiCut (Noise High Cut)	53Hz...20.0kHz, THRU

Sets the high-cut frequency for the noise

49:Mn.Ring Modulator (Mono Ring Modulator)

Oscillator (Oscillator Frequency)	0...12.00kHz
	Sets the oscillator frequency
*LFO Speed	0.02...20.00Hz
Sets the LFO speed of the oscillator frequency modulation
*LFO Depth	0...100%

Sets the depth of LFO modulation for the oscillator frequency

Dry:Wet	Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Delay (Delay Time)	0...2.730sec
	Sets the delay time
Feedback	–100...+100%
	Sets the feedback amount
HiDamp (High Damp)	53Hz...20.0kHz, THRU
Sets the damping amount in the high range
In Level (Input Level)	0...100%
	Sets the input level to the effect

50:Tube Pre Amp Sim (Tube PreAmp Simulator)

This effect simulates a vacuum tube preamp. You can make independent settings for two vacuum tubes connected in se- ries, producing a distinctive and warm sound.

Tube1.Gain	–24.0...+24.0dB
	Sets the gain of tube circuit 1
Tube1.Sat (Tube1 Saturation)	0...100%
Sets the amount of saturation for tube circuit 1
Tube2.Gain	–24.0...+24.0dB
	Sets the gain of tube circuit 2
Tube2.Sat (Tube2 Saturation)	0...100%
Sets the amount of saturation for tube circuit 2
Tb1.LoCut (Tube1 Low Cut)	THRU, 21Hz...8.00kHz

Sets the amount of low-frequency attenuation for tube circuit 1

Tb1.HiCut (Tube1 High Cut)53Hz...20.0kHz, THRU

Sets the amount of high-frequency attenuation for tube circuit 1

Tb2.LoCut (Tube2 Low Cut)THRU, 21Hz...8.00kHz

Sets the amount of low-frequency attenuation for tube circuit 2

Tb2.HiCut (Tube2 High Cut)53Hz...20.0kHz, THRU

Sets the amount of high-frequency attenuation for tube circuit 2

Tube1Bias	0...100%
	Sets the bias for tube circuit 1
Tb1.Phase (Tube1 Phase)	Normal, Inverted
	Sets the output phase of tube circuit 1
Tube2Bias	0...100%
	Sets the bias for tube circuit 2
Out Level (Output Level)	–48.0...0.0dB
	Sets the output level

162