LoDamp (Low Damp)

THRU, 21Hz...8.00kHz

Sets the damping amount in the low range

HiDamp (High Damp)

53Hz...20.0kHz, THRU

Sets the damping amount in the high range

 

 

In Level (Input Level)

0...100%

 

Sets the input level to the effect

: Type

The left/right panning of the delay can be modified by chang- ing the connections of the left and right delay. Be aware that dif- ferent sounds must be input to the left and right channels in order for this parameter to be effective.

11: St.Modulation Dly

(Stereo Modulation Delay)

This stereo delay uses an LFO to sweep the delay time. The pitch also varies. You will obtain a delay sound with swell and shimmering. You can also control the delay time using a modulation source.

L Time (L Delay Time)

0...2.500sec

 

Sets the left delay time

 

 

R Time (R Delay Time)

0...2.500sec

 

Sets the right delay time

*LFO Speed

0.02...20.00Hz

 

Sets the LFO speed

 

 

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

 

 

*L Depth

0...200

Sets the depth of the left LFO modulation

*R Depth

0...200

Sets the depth of the right LFO modulation

 

 

LFO Wave (LFO Waveform)

Triangle, Sine

 

Selects LFO Waveform

 

 

LFO Shape

–100...+100%

Determines how much the LFO waveform is changed

L Fdback (L Feedback)

–100...+100%

Sets the feedback amount of left delay

 

 

R Fdback (R Feedback)

–100...+100%

Sets the feedback amount of right delay

 

 

L Phase (L LFO Phase)

–180...+180deg

Sets the phase obtained when the left LFO is reset

R Phase (R LFO Phase)

–180...+180deg

Sets the phase obtained when the right LFO is reset

: L LFO Phase [degree], : R LFO Phase [degree]

“L LFO Phase” and “R LFO Phase” specify the phase differ- ence between the two LFO’s when they are reset. This allows the pitch change of the sweep to be set independently for left and right.

12:St.Dynamic Delay (Stereo Dynamic Delay)

This stereo delay controls the level of delay according to the input signal level. You can use this as a ducking delay that applies delay to the sound only when you input signals at a high velocity or only when the volume level is low.

L Time (L Delay Time)

0...2.730sec

 

Sets the left delay time

 

 

R Time (R Delay Time)

0...2.730sec

 

Sets the right delay time

Feedback

–100...+100%

 

Sets the feedback amount

 

 

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

 

 

Threshold

0...100

 

Adjusts the level at which compression

Attack

0...1.00sec

 

Sets the attack time of level control

Release

0...10.0sec

 

Sets the release time of level control

 

 

Offset

0...100%

 

Sets the offset of level control

 

 

Control (Control Target)

None, WetLevel, Feedback

Selects from no control, output, and feedback

LoDamp (Low Damp)

THRU, 21Hz...8.00kHz

Sets the damping amount in the low range

 

 

HiDamp (High Damp)

53Hz...20.0kHz, THRU

Sets the damping amount in the high range

 

 

Spread

0...100%

Sets the width of the stereo image of the effect sound

Polarity

[+]Plus, [–]Minus

 

Reverses level control

: Control Target

This parameter selects no level control, delay output control (effect balance), or feedback amount control.

: Polarity, : Threshold, : Offset, : Attack, : Release

The “Offset” parameter specifies the value for the “Control Target” parameter (when level control is not being applied), expressed as a ratio relative to the parameter setting.

If “Polarity” is set to [+] Plus, “Control Target” will be the value of the parameter multiplied by the “Offset” when the input signal is lower than the “Threshold,” or will be the value of the parameter when the input signal is above the “Thresh-

old.”

If “Polarity” is set to [–] Minus, “Control Target” will be the value of the parameter when the input signal is lower than the “Threshold,” or will be the value of the parameter multiplied by the “Offset” when the input signal is above the “Thresh-

old.”

The “Attack” and “Release” parameters specify attack time and release time of delay level control.

13: Auto Panning Delay

This stereo delay effect pans the delay sound left and right using the LFO.

L Time (L Delay Time)

0...2.730sec

 

Sets the left delay time

 

 

R Time (R Delay Time)

0...2.730sec

 

Sets the right delay time

*Speed (Panning Speed)

0.02...20.00Hz

 

Sets the panning speed

 

 

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

 

 

L Fdback (L Feedback)

–100...+100%

Sets the feedback amount for the left channel

R Fdback (R Feedback)

–100...+100%

Sets the feedback amount for the right channel

 

 

*Depth (Panning Depth)

0...100

 

Sets the panning width

 

 

L-R Phase (LFO L-R Phase)

–180...+180deg

Sets the LFO phase difference between the left and right

LoDamp (Low Damp)

THRU, 21Hz...8.00kHz

Sets the damping amount in the low range

 

 

HiDamp (High Damp)

53Hz...20.0kHz, THRU

Sets the damping amount in the high range

 

 

Waveform (LFO Waveform)

Triangle, Sine

 

Selects LFO Waveform

LFO Shape

–100...+100%

Determines how much the LFO waveform is changed

154

Page 164
Image 164
Korg D3200 owner manual 154, 11 St.Modulation Dly Stereo Modulation Delay, Auto Panning Delay