Korg D3200 156, Stereo Tremolo, Stereo Expander, 19 St.Pitch Shifter Stereo Pitch Shifter

Release	0...10.0sec
Sets the release time for level control
L-R Phase (LFO L-R Phase)	–180...+180deg
Sets the LFO phase difference between the left and right
Waveform (LFO Waveform)	Triangle, Sine
	Selects LFO Waveform
LFO Shape	–100...+100%

Determines how much the LFO waveform is changed

18: Stereo Tremolo

This effect modulates the volume level of the input signal. The effect is stereo, and offsetting the LFO of the left and right phases from each other produces a tremolo effect be- tween left and right.

*Speed (LFO Speed)	0.02...20.00Hz
	Sets the LFO speed
*Depth	0...100
	Sets the depth of LFO modulation

Waveform (LFO Waveform)

Triangle, Sine, Square, Saw up, Saw down

Selects LFO Waveform

Dry:Wet	Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
LFO Shape	–100...+100%
Determines how much the LFO waveform is changed
L-R Phase (LFO L-R Phase)	–180...+180deg

Sets the LFO phase difference between the left and right

: LFO Waveform

This parameter selects the LFO waveform.

: LFO Phase

This parameter determines the difference between the left and right LFO phases. A higher value will simulate the auto-pan effect in which the sound is panned between left and right.

19:St.Pitch Shifter (Stereo Pitch Shifter)

This is a stereo pitch shifter.

PitchShift	–24...+24/2tone
Sets the pitch shift amount in steps of a semitone
Fine	–100...+100cent
Sets the pitch shift amount in steps of one cent
Lo/Hi Cut (Low/High Cut)	Lo:–50%..., Flat, ...Hi:–50%
Sets the damping amount in the low/high range
Dry:Wet	Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Feedback	–100...+100%
	Sets the feedback amount
L Time (L Delay Time)	0...1.360sec
	Sets the left delay time
R Time (R Delay Time)	0...1.360sec
	Sets the right delay time
Fb.Position (Feedback Position)	Pre (Pitch), Post (Dly)
Switches the feedback connection
In Level (Input Level)	0...100%
	Sets the input level to the effect
Spread	–100...100%

Sets the width of the stereo image of the effect sound

: Feedback Position, : Feedback

If “Feedback Position” is set to Pre (Pitch), the output of the pitch shifter will be fed back into the input of the pitch shifter; this means that by raising the “Feedback” value you can create an effect in which the pitch of the feedback continues to rise (or fall) each time the feedback delay is repeated.

If “Feedback Position” is set to Post (Dly), the sound that is fed back will not be sent through the pitch shifter again; this means that if you raise the “Feedback” value, the pitch-shifted sound will repeat at that same pitch.

Category: Dynamics&Filter

Dynamics/Filter-type effects

20: Stereo Compressor

This effect compresses the input signal to regulate the level and give a “punchy” effect. This is a stereo compressor. You can link left and right channels, or use each channel separate- ly.

Threshold	–30.0...0.0dB
Sets the level at which compression begins to apply
Ratio	1.00:1...20.0:1
Sets the compression ration of the signal
Attack	0...1.00sec
	Sets the attack time
Release	0...10.0sec
	Sets the release time
Env.Select (Envelope Select)	L/R Mix, L/R Indiv

Switches the left/right channels between linked or independent operation

Response	Slow, Medium, Fast
	Selects the response speed
Tube Sat (Tube Saturation)	0...100
Sets the depth of vacuum tube distortion
Out Gain (Output Gain)	–24.0...+24.0dB
	Adjusts the output level gain

: Envelope Select

This parameter selects whether the left and right channels are linked to control both signals simultaneously, or whether each channel is controlled independently.

: Response

Adjusts the response speed at which the envelope is detected. Select the setting that is appropriate for the input material; choose Fast for brief sounds like percussion instruments, Medium for vocals, or Slow for long-sustaining sounds.

21: Stereo Expander

This effect attenuates input signals that are below a specified level, adding punch to the sound and improving the S/N ra- tio by reducing the level between performances.

Threshold	–48.0...0.0dB
Sets the level at which compression begins to apply
Ratio	1.00:1...20.0:1
Sets the compression ration of the signal
Attack	0...1.00sec
	Sets the attack time
Release	0...10.0sec
	Sets the release time
Env.Select (Envelope Select)	L/R Mix, L/R Indiv

Switches the left/right channels between linked or independent operation

Response	Slow, Medium, Fast
	Selects the response speed
Out Gain (Output Gain)	–24.0...+24.0dB
	Adjusts the output level gain

156