Can’t use the expression pedal or MIDI to control an effect

In the SYSTEM/MIDI, “Control” tab page, is the effect selected by “Control Change Assign” enabled?

Go to the EFFECT, “EFFRouting” tab page and verify that the effect is enabled.

Are you using the correct device to control the effect?

Control the effect using the device specified by the

“Control Change Device” setting in the SYSTEM/ MIDI, “Control” tab page. (p.119)

Is the selected effect set to effect program number “000” (=NO EFFECT) or to an effect program number that does not include a control function?

If you are controlling via MIDI, does the MIDI channel number of the D3200 match the MIDI channel of the transmitting MIDI device? (p.124)

Is the effect program’s Ctrl setting turned on? (p.57)

Can’t apply external effect (AUX)

Is the external send level setting set to zero or nearly zero?

Go to the MIXER, SEND (EFF/AUX/REC), “AUX1 Send”/“AUX2 Send” tab page, and raise the external send level.

Is the output of your external effect connected to the INPUT 1–INPUT 12 jacks, and input to the mixer channels?

Go to the MIXER, CH INPUT/SubMixer, “Ch Assign” tab page and make the appropriate assignments.

Have sub input settings been made correctly? (p.44, 101)

Session Drums

Drum sound is not output

Is the DRUMS key turned off?

Is the DRUMS fader lowered?

Is the rhythm assign setting appropriate?

If the rhythm is assigned to a CH Input, input the rhythm to a mixer channel.

Is the recorder stopped?

Press the PLAY key to play back. The rhythm will sound while the recorder is recording or playing,

If you want to preview the rhythm while the recorder is stopped, go to the SESSION DRUMS, “SessionDr.” tab page and turn the RUN button on.

You may have selected a silent drum pattern. The session drum volume may be too low.

Use DRUMS fader to adjust the volume.

Can’t hear the drum

Is the DRUMS key off? (p.59)

A key does not function when pressed

Some keys do not function while the recorder is playing or recording.

Stop the recorder, and then perform the operation.

Some keys do not function while Scrub is on.

Turn off Scrub, and then perform the operation. (p.40, 146)

Is a dialog box open?

Click either the Yes, No button to close the dialog box.

The 1–16/17–32 key does not work

In the case of a 24-bit song, only sixteen channels are available, so this key will not function.

MIDI

MIDI sequencer won’t synchronize/MIDI control is not possible

Are the MIDI cables connected correctly? (p.11) A MIDI cable may be broken.

Can’t synchronize using MTC or MIDI Clock

Are the master and slave settings correct? (p.125) Does the synchronization signal being output by the D3200 match the synchronization signal your MIDI sequencer is receiving?

Go to the SYSTEM/MIDI, “MIDI/MMC” tab page and check the “MIDI Sync” setting. (p.125)

Are the synchronization settings of your MIDI sequencer appropriate?

Refer to the owner’s manual of your MIDI sequencer.

The D3200 doesn’t receive MMC

In the SYSTEM/MIDI, “MIDI/MMC” tab page, is “MMC Mode” set to “Receive”?

In the above page, is “MMC Device ID” set to match the MMC device ID setting of your MIDI sequencer? (p.125)

For some MIDI sequencers, the MMC device ID setting may differ.

Is your MIDI sequencer set to transmit MMC?

Refer to the owner’s manual of your MIDI sequencer.

Can’t use MIDI to control scenes

Do the MIDI channels of the D3200 and your MIDI sequencer match?

Go to the SYSTEM/MIDI, “MIDI/MMC” tab page and check the “Global Ch” setting. (p.125)

Are program changes turned off?

Check the settings in the SYSTEM/MIDI, “MIDI/ MMC” tab page. (p.124)

The D3200 does not synchronize as a slave

If the D3200 is set as an MTC slave, it may take several seconds for synchronization to occur.

Do the Frame Rate settings match? (p.125)

If you are using MTC to synchronize, the MIDI se- quencer to which you are synchronizing must support MTC.

Can’t control another device via MMC

In the SYSTEM/MIDI, “MIDI/MMC” tab page, is “MMC Mode” set to “Transmit”?

Is the MMC slave device set so that it will receive MMC? Does the D3200’s MMC Device ID match the external MIDI device’s MMC Device ID?

Can’t use MIDI to control mixer parameters

Is the device that is receiving the control changes set to record all MIDI channels 1–16?

Are control changes turned off?

Check the settings in the SYSTEM/MIDI, “MIDI/ MMC” tab page. (p.124)

166

Page 176
Image 176
Korg D3200 owner manual 166, Key does not function when pressed